Advertisement
Quick Links
*Photo shows a 2' x 8' system. Actual system is 2' x 4'. Some components shown are not included with kit. Actual system differs.
©2020 FarmTek
®
All Rights Reserved. Reproduction
is prohibited without permission.
Revision date: 01.27.20
115554
Ebb & Flow System*
ATTENTION: ACTUAL TRAY IS BLACK. ORIGINAL
WHITE TRAY IS NO LONGER AVAILABLE.
115554
2' x 4' System
1
Advertisement
Related Manuals for FarmTek Growers Supply 115554
Summary of Contents for FarmTek Growers Supply 115554
- Page 1 ATTENTION: ACTUAL TRAY IS BLACK. ORIGINAL WHITE TRAY IS NO LONGER AVAILABLE. *Photo shows a 2' x 8' system. Actual system is 2' x 4'. Some components shown are not included with kit. Actual system differs. ©2020 FarmTek ® All Rights Reserved. Reproduction is prohibited without permission.
- Page 2 Important Information READ THIS DOCUMENT BEFORE YOU BEGIN Thank you for purchasing the 115554 Ebb & Flo system. When properly assembled and maintained, this system will provide years of reliable service. These instructions include helpful hints and important information needed to safely assemble the system. Please read and understand these instructions before you begin.
- Page 3 Attach Leg Tubes ATTACH LEG TUBES 115554H Assemble frame on a flat, level surface. 115554L Bottom 112838 of Leg Tek Screw Tube FAME51B Washer 112477 115554L FALB34B FAG338B Hex Bolt FALB34B 5. Secure leg tubes to 115554H tubes using FAG338B flat head Locknut bolts and FAME51B washers.
- Page 4 Assemble Main Frame STEP 2 ASSEMBLE MAIN FRAME Assemble frame on a flat, level surface. 112770 STEP 1 115554C 115554C FAME51B FAG338B 1. Use the FAG338B (5/16" x 3") hex head bolts and FAME51B flat washers to complete the frame assembly. Tighten all connections until snug. 2.
- Page 5 Prepare Propagation Tray ATTENTION: ACTUAL TRAY IS BLACK. ORIGINAL PREPARE 111104 PROPAGATION TRAY (2' x 4') WHITE TRAY IS NO LONGER AVAILABLE. Actual tray design may differ from example shown. Complete these steps to drill the holes in the propagation tray. 1.
- Page 6 Install Bulkhead Fittings INSTALL BULKHEAD FITTINGS System is equipped with two (2) 111301 bulkhead fittings which are used to connect the tray to the lower reservoir. Gather these parts and install the fittings: • 111301 Bulkhead fittings (2) 1. Flip tray over so inside is facing 2.
- Page 7 Assemble In-Line Valves ASSEMBLE IN-LINE VALVES 2. Cut two (2) three inch (3") pieces 3. Secure each connection using of 3/4" tubing (111627) and slide one 111698 ratchet clamp. one onto each AC2804 in-line Gently squeeze clamp until it valve. clicks indicating clamp is tight.
- Page 8 Install Pump and Attach Supply and Drain Tubes INSTALL PUMP AND SUPPLY TUBE 1. Slide lid back and set pump in 2. Cut a section of 3/4" tube to 3. Take pump and slide supply tube reservoir. Center pump under length and check fit.
- Page 9 Install Pump and Attach Supply and Drain Tubes INSTALL PUMP AND SUPPLY LINE AND DRAIN TUBE—continued 10. Take the remaining valve 11. Slide assembly onto remaining 12. Measure from valve to top of 8. Secure connection using pliers to squeeze ratchet clamp. assembly and slide a ratchet bulkhead fitting and secure lid and add 2"-3"...
- Page 10 Prepare Porthole Cover PREPARE PORTHOLE COVER The porthole cover protects tank contents from light and debris, which helps prevent algae growth. During system operation keep this cover in place at all times. The steps that follow describe one way to prepare porthole cover. 1.
- Page 11 Adjust Levelers Actual system may differ ADJUST LEVELERS from what is shown. Use the lower photos to determine how to set the slope of the frame. After adjusting each leveler as needed, use photos 1-4 to lock leveler in place. A 9/16" wrench is needed. Adjust levelers so tray is level side- Adjust levelers so tray slopes to-side.
- Page 12 Install Bulkhead Screen and Extensions INSTALL BULKHEAD SCREENS AND EXTENSIONS Bulkhead screens and extensions allow you to manage nutrient solution level in the tray. Screens can be used with or without extensions. Depending on the application, extensions can be used with one screen on the drain tube to increase and maintain the nutrient solution level in the tray.
- Page 13 Sample System Photo ATTENTION: ACTUAL TRAY IS BLACK. ORIGINAL WHITE TRAY IS NO LONGER AVAILABLE. ATTENTION: Actual system may differ. Photo shows a 2' x 8' tray and frame. Plumbing and assembly are the same. Some components shown are not included with ebb & flow kit. Revision date: 01.27.20 115554...