Advertisement
Quick Links
©2018 Growers Supply
All Rights Reserved. Reproduction
is prohibited without permission.
Revision date: 06.27.18
GROWSPAN
Round Pro Greenhouses and Systems
Photo may show a different but similar model.
ROUND PRO GREENHOUSES AND SYSTEMS
™
GrowSpan
™
STK#
DIMENSIONS
104853
20' W x 10' 7" H x 20' L
104854
20' W x 10' 7" H x 24' L
104855
20' W x 10' 7" H x 36' L
104856
20' W x 10' 7" H x 48' L
1
Advertisement
Related Manuals for FarmTek Growers Supply GrowSpan Round Pro Series
Summary of Contents for FarmTek Growers Supply GrowSpan Round Pro Series
- Page 1 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ GrowSpan ™ Round Pro Greenhouses and Systems Photo may show a different but similar model. STK# DIMENSIONS 104853 20' W x 10' 7" H x 20' L 104854 20' W x 10' 7" H x 24' L 104855 20' W x 10' 7"...
-
Page 2: Safety Precautions
GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ LOCATION Choosing the proper location is an important step before you begin to assemble the structure. The following suggestions and precautions will help you determine whether your selected location is the best location. •... -
Page 3: Assembly Procedure
GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ ASSEMBLY PROCEDURE • Band Clamp: Clamp used to connect the end wall framing to the rafter pipe. In some cases, band Following the instructions as presented will help ensure clamps are also used to connect diagonal struts to the the proper assembly of your greenhouse. -
Page 4: Required Tools
GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ SPECIAL NOTE: Baseboards for Frame REQUIRED TOOLS These instructions describe installing a baseboard The following list identifies the main tools needed to (recommended) at ground level along each side of the assemble the shelter. Additional tools and supports may be frame. - Page 5 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ The following graphics and photos will help you identify the different parts and show you how they are used. (Some parts are not shown.) FA4482B CC6212 QH1402 103544 102569 102921B & FA4484B Tek Screw Fabric Clip Band Clamp Mounting Plate...
- Page 6 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ H-CHANNEL INSTALLATION INSTRUCTIONS The new H-channel design requires installation of the flat side facing out with channel side toward the building. Some diagrams and photos in this document show installation of original H-channel with channel side facing out.
- Page 7 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ GrowSpan ™ Round Pro Greenhouses and Systems OVERVIEW This section describes assembling your Round Pro Greenhouse. For details, please see section, Assembling the Round Pro Greenhouse Components. See illustration below to identify main parts of greenhouse. ATTENTION: Position purlins evenly during the frame assembly.
- Page 8 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ LAY OUT THE BUILDING SITE 3. Use a transit or line level to drive the second corner post to the same depth as the first ground post. After the site is prepared, lay out the building site. 4.
-
Page 9: Rafter Assembly
GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ ASSEMBLING THE ROUND PRO GREENHOUSE 2. Slide three (3) end purlin clamps over the rafter pipes. FRAME COMPONENTS After the site is prepared and an inventory of parts is complete, continue with the rafter assembly. NOTE: All rafter assemblies consist of rafter tubes and purlin clamps. -
Page 10: Frame Assembly
GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ RAFTER ASSEMBLY (continued) FRAME ASSEMBLY INTERIOR RAFTER ASSEMBLY After all ground posts are driven in place and rafters are assembled, assemble the frame. Complete the following steps for the interior rafters. 1. Select the pipes for the first interior rafter assembly and NOTE: The baseboards (strongly recommended) shown in position these on the ground as shown. - Page 11 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ FRAME ASSEMBLY (continued) 2. Secure the leg pipes to the ground posts using the 5/16" x 2 1/2" machine bolts and nuts. 4. From the location marked in the previous step, measure forty-eight inches (48") and make another Rafter mark on the assembled purlin.
- Page 12 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ FRAME ASSEMBLY (continued) 10. Move to the interior rafter and align the mark on the purlin with the center of the rafter to maintain the proper 5. As the second rafter is steadied, remove one section of rafter spacing.
- Page 13 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ FRAME ASSEMBLY (continued) BASEBOARD INSTALLATION (RECOMMENDED) 18. Secure each purlin pipe joint with a Tek screw. Gather the parts: 19. Repeat the above steps as needed to stand and secure • Treated or recycled plastic lumber (supplied by the remaining interior rafters and purlins to complete customer).
- Page 14 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ SIDE STRUT INSTALLATION 3. Attach the remaining end of the strut to the baseboard using a lag screw or nut and bolt (not included). See There are four (4) side struts for the shelter. These struts the diagram that follows for location.
- Page 15 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ END WALL INSTALLATION • DO NOT REPOSITION THE END WALL VERTICALS USED AT THE SEAM OF TWO (2) POLYCARBONATE The steps to install the end walls for the greenhouse PANELS. include the following: •...
- Page 16 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ END WALL INSTALLATION (continued) 9. Measure the distance between the top of the base tube and band clamp (Step 7) to determine the length of the 4. Secure the base tube between the legs of the end first vertical section of the door frame tube.
- Page 17 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ INSTALL THE END WALL FRAME (continued) 17. Using a level (or other means), verify that one vertical door frame tube is plumb and tighten the band clamp 15. Using the marks on the base tube for the rough bolt to lock the first door frame member in place.
- Page 18 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ INSTALL THE END WALL FRAME (continued) 26. With the square-to-round tube connect bracket attached to the top of the frame member, place a 22. Using the end frame diagrams (Quick Start section), square tube fitting on the bottom of the frame member. measure and mark (on the base tube) the locations of the remaining vertical end wall supports.
- Page 19 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ INSTALL THE END WALL FRAME (continued) TAPE SHARP EDGES AND CONNECTORS After the frame is assembled, check the frame for sharp INSTALL THE BACK END WALL FRAME edges that could damage the cover or end panel, and file these smooth or tape over them using the supplied duct The end wall framing for the back of the greenhouse is tape.
- Page 20 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ END PANEL INSTALLATION Secure all polycarbonate panels as shown in the diagrams and photos below, unless otherwise noted. After end wall framing is installed, attach polycarbonate panels to end wall framing. Steps that follow describe one way to complete panel installation.
- Page 21 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ END PANEL INSTALLATION (continued) 4. Place panel in position, attach it to end wall framing using FA4484B Tek screws. Complete the following general steps to install end wall panels. H-channel here – outer edge of panel. 1.
- Page 22 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ END PANEL INSTALLATION (continued) a. Cut angled notches from profile to allow bending. 6. Working towards other edge of same end wall, secure next panel in place. Cut and attach the correct profile to the proper edges.
- Page 23 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ 5. Measure, cut and install U-channel profile (104213) to DOUBLE DOOR ASSEMBLY all edges of the panel. The materials and parts needed to assemble the doors include: Photo shows panel attached to the outside of the door frame and finished with U-channel.
- Page 24 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ DOUBLE DOOR ASSEMBLY (continued) a. Photo shows end cap as attached to door frame tube. View shows assembly from the outside. 8. Next, with assistance, lift door and attach to end wall frame using the long Tek screws. b.
- Page 25 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ DOUBLE DOOR ASSEMBLY (continued) 11. Next, install another section of end cap on the inside Space below is reserved for customer notes. frame of the door that includes the chain latch. NOTE: This length of end cap will act as a stop for the remaining door of the double door when both doors are closed.
- Page 26 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ INSTALL POLY LATCH U-CHANNEL 3. Continue to attach the U-channel sections to the rafters (or ribbon board if used) and work toward the other end Gather the parts: of the frame. Cut the last section of U-channel to the required length so that it is flush with the end wall panel (if needed).
- Page 27 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ INSTALL POLY LATCH U-CHANNEL (continued) 3. After tying the ropes to the main cover, throw the ropes over the top of the greenhouse and pull the covers into The steps that follow describe one way to complete this place.
- Page 28 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ INSTALL MAIN COVER (continued) 12. Once the first cover is stretched and secure, install the inflation fan kit in the desired location and according to 6. The rope can remain in place to temporarily secure the the instructions sent with the kit.
- Page 29 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ INSTALL MAIN COVER (continued) ATTACH CONDUIT TO MAIN COVER ROLL-UP SIDE Gather the parts: ASSEMBLE THE ROLL-UP SIDE CONDUIT Gather the Parts: • Assembled conduits • Pipe 1.315'' x 75'' swaged 17 GA (#131S0075) •...
- Page 30 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ TWIST-OF-THE-WRIST ASSEMBLY 3. Select the aluminum channel and drill a 3/8" hole through the channel approximately 2" from the end and Gather the parts: attach a threaded rod using a 3/8" nut on each side of the channel.
- Page 31 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ TWIST-OF-THE-WRIST ASSEMBLY (continued) 11. Using a carriage bolt, attach the square shaft to a tubing adapter. 6. Select the bearing bracket and attach the bearings as needed. (In some instances, the bearings may come already attached.) Assemble as follows: NOTE: Single bearings are attached to the sides of the bracket and double bearings to the middle portion...
- Page 32 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ TWIST-OF-THE-WRIST ASSEMBLY (CONTINUED) ATTENTION: If no wood baseboard is present as required, additional steps must be take to anchor 15. Attach the rolled conduit to the square shaft of the the lower portion of the anti-billow ropes. (Contact assembly by inserting a carriage bolt through the hole Customer Service at 1-800-245-9881 to purchase in the conduit and tubing adapter.
- Page 33 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ INSTALL ANTI-BILLOW ROPES (CONTINUED) SHELTER CARE AND MAINTENANCE INSTALL ANTI-BILLOW ROPES (CONTINUED) Proper care and maintenance of the shelter is important. 6. Cut the rope and tie one end to the eyebolt. Check the following items periodically to properly maintain 7.
- Page 34 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ 10'-3 5/16" Height QUICK START GUIDE 20' Round Pro Greenhouse 20'-0 5/8" Width FRONT Grid Represents 12" Squares Ground Level Frame shown may differ in length from actual frame. Revision date: 06.27.18...
- Page 35 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ Revision date: 06.27.18...
- Page 36 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ Revision date: 06.27.18...
- Page 37 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ Revision date: 06.27.18...
- Page 38 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ Revision date: 06.27.18...
- Page 39 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ Revision date: 06.27.18...
- Page 40 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ Revision date: 06.27.18...
- Page 41 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ Revision date: 06.27.18...
- Page 42 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ Revision date: 06.27.18...
- Page 43 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ Revision date: 06.27.18...
- Page 44 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ Revision date: 06.27.18...
- Page 45 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ Revision date: 06.27.18...
- Page 46 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ Revision date: 06.27.18...
- Page 47 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ Space below is reserved for customer notes. Revision date: 06.27.18...