Gardena EasyClean Li Operator's Manual page 4

d) Operate the machine in a recommended position and
only on a firm, level surface.
e) Do not operate the machine on a paved or gravel sur-
face where ejected material could cause injury.
f) Before using, always visually inspect to see, that the
shredding means, shredding means bolts and other
fasteners are secure, the housing is undamaged and
that guards and screens are in place. Replace worn
or damaged components in sets to preserve balance.
Replace damaged or unreadable labels.
g) Before use, check the supply and extension cord for
signs of damage or aging. If the cord becomes dam-
aged during use, disconnect the cord from the supply
immediately. DO NOT TOUCH THE CORD BEFORE
DISCONNECTING THE SUPPLY. Do not use the
machine if the cord is damaged or worn.
h) Never operate the machine while people, especially
children, or pets are nearby.
3. Operation
a) Before starting the machine, make certain that the
feeding chamber is empty.
b) Keep your face and body away from the feed intake
opening.
c) Do not allow hands or any other part of the body or
clothing inside the feeding chamber, discharge chute,
or near any moving part.
d) Keep proper balance and footing at all times. Do not
overreach. Never stand at a higher level than the
base of the machine when feeding material into it.
e) Always stand clear of the discharge zone when
operating this machine.
f) When feeding material into the machine be extremely
careful that pieces of metal, rocks, bottles, cans or
other foreign objects are not included.
g) If the cutting mechanism strikes any foreign objects
or if the machine should start making any unusual
noise or vibration, immediately shut off the power
source and allow the machine to stop. Disconnect
the machine from the supply and take the following
steps before restarting and operating the machine:
– inspect for damage;
– replace or repair any damaged parts;
– check for and tighten any loose parts.
h) Do not allow processed material to build up in the
discharge zone; this may prevent proper discharge
and can result in kickback of material through the
intake opening.
i) If the machine becomes clogged, shut-off the power
source and disconnect the machine from supply
before cleaning debris.
j) Never operate the machine with defective guards or
shields, or without safety devices.
k) Keep the power source clean of debris and other
accumulations to prevent damage to the power source
or possible fire.
l) Do not transport this machine while the power source
is running.
m) Stop the machine, and remove plug from the socket.
Make sure that all moving parts have come to a com-
plete stop
12
– whenever you leave the machine,
– before clearing blockages or unclogging chute,
– before checking, cleaning or working on the
machine.
n) Do not tilt the machine while the power source is
running.
4. Maintenance and storage
a) When the machine is stopped for servicing, inspection,
or storage, or to change an accessory, shut off the
power source, disconnect the machine from the sup-
ply and make sure that all moving parts are come to
a complete stop. Allow the machine to cool before
making any inspections, adjustments, etc. Maintain
the machine with care and keep it clean.
b) Store the machine in a dry place out of the reach of
children.
c) Always allow the machine to cool before storing.
d) When servicing the shredding means be aware that,
even though the power source is switched off due
to the interlock feature of the guard, the shredding
means can still be moved.
e) Replace worn or damaged parts for safety. Use only
genuine replacement parts and accessories.
f) Never attempt to override the interlocked feature of the
guard.
Additional safety warnings
Battery safety
DANGER! Fire risk!
The battery product to be charged must be placed
on a nonflammable, heat resistant and non-conduc-
tive surface while charging.
Keep corrosive, flammable and easily combustible
objects clear of the battery charger and the battery
product.
Do not cover the battery charger and the battery
product while charging.
Disconnect the battery charger immediately in the event
of smoke formation or fire.
Only use the original GARDENA Charger to charge the
battery. The use of other battery chargers may damage
the batteries irreparably and even cause a fire.
Do not charge any third-party batteries. There is a risk
of fire and explosion!
If you notice fire: Extinguish the flames with oxygen
reducing materials.
DANGER! Risk of explosion!
Protect battery products from heat and fire. Do not
leave on radiators or expose to strong sunshine for
long periods.
Do not operate in explosive atmospheres, such as
in the presence of flammable liquids, gases, or dust.
Battery products may create sparks which could
ignite the dust or fumes.