Pure Fun 9011TS Product Manual page 10

STEP 8
ASSEMBLY INSTRUCTIONS
Attach the R-Hooked Galvanized Spring (#8) with " R" Hook end to the Triangle-Ring on the mat as shown below.
HINT: Holding the spring at 45 degree in relation to the mat surface will be much easier to install into Triangle -Ring.
Hold the spring loading tool underhand and pull spring hook towards the point "ZERO" on the Top Rail frame as shown
FIGURE 8. Drop hook into frame hole until it latches on completely and tap it down if hook is not completely in the hole.
R-Hook
" R" HOOK END
STEP 9
Attach a spring at every 3 holes and corresponding Triangle-rings. For even distribution of tension and ease of assembly,
springs should be placed on opposite sides of the mat/frame.....i.e. 3 then 21, 33 then 15, etc. In addition to the previously
installed springs, you should have springs at 3, 9, 15, 21, 27, and 33 as shown in FIGURE 10.
C-Hook
1
12
11
(# 1)
(#1)
10
STEP 10
9
8
Then, attach the remaining 18 springs by using the same theory of counting equal holes as shown in FIGURE11.
STEP 10
Then, attach the remaining 18 springs by using the same theory of counting equal holes as shown in FIGURE11.
If you notice that you have miscount a hole and Triangle-rings connection, recount and remove or attach any springs
required to maintain the count of springs.
STEP 11
(# 1)
Flip down the Safety Pad stitched with the trampoline mat (#1). Pull tight the elastic straps over the frame as shown in
STEP 11
FIGURE 12 and make sure safety pad covers the frame.
Flip down the Safety Pad stitched with the trampoline mat (#1). Pull tight the elastic straps over the frame as shown in
FIGURE 12 and make sure safety pad covers the frame.
18
18
Perform a complete inspection of the trampoline to make sure all parts are assembled and attached properly.
Read this entire manual and make sure all jumpers completely understand all of the safety rules printed in the manual and
on the various warning signs. Instruct all jumpers in the basic bounces
!
Perform a complete inspection of the trampoline to make sure all parts are assembled and attached properly.
frame and all springs before using this trampoline. Do not use trampoline if even one spring or Triangle-ring is damaged or
missing.
Read this entire manual and make sure all jumpers completely understand all of the safety rules printed in the manual and
on the various warning signs. Instruct all jumpers in the basic bounces
!
10
IMPORTANT NOTICE: Make sure the safety pad is securely attached to the frame and completely covers the
frame and all springs before using this trampoline. Do not use trampoline if even one spring or Triangle-ring is damaged or
missing.
2
17
3
18
4
5
17
FIGURE 9
6
7
CAUTION:
(# 1)
(#1)
(# 1)
FIGURE 10 Trampoline Pad
(In lift-up position)
Trampoline Pad
(In lift-up position)
IMPORTANT NOTICE: Make sure the safety pad is securely attached to the frame and completely covers the
described
(# 1)
Step 9
Spring(#7)
SPRING (#8)
FIGURE 8
Opening
POINT ZERO
13
14
(# 1)
(#1)
15
16
18
18
FIGURE 11
FIGURE 11
Step 10
ELASTIC STRAP
Elastic Strap
FIGURE 12
ELASTIC STRAP
described in the manual. FIGURE 12
in the manual.
GQBrands.com
19
in
STEP 9:
Attach all 36 Springs Hook ends (Part #7) using
the Spring Loading Tool (Part #16) to all Top Rail
Openings by following the correct placement
order. The R-Hook end should be attached to
SPRING LOADING TOOL(#9)
FIGURE 9
Trampoline Mat, and C-Hook to Top Rail.
For even distribution of tension and ease of
assembly, springs should be placed on opposite
sides of the mat/frame. Attach springs 1-18 in
the correct numerical order to properly distribute
tension of the mat.
Once the first 18 springs have properly attached
to all Top Rails, install the remaining springs to
complete the installation of the trampoline mat
onto the foundation.
FIGURE 10
STEP 10:
Tie down the all elastic straps attached to the
trampoline pad into the top rails tightly.
CustomerService@GQBrands.com 1-866-498-5269