Technical Data - Graco Series B Instructions-Parts List Manual

Maximum working pressure
Pump air requirements
Pump air consumption
Maximum recommended pump speed
Agitator air consumption
Pump cycles per gallon (liter)
Wetted parts
Air Inlet Size
Fluid Outlet Size
Fluid Return Port Size
Fluid Intake Size
Not all ECO changes made to part number 225815 have been implemented in the body of this manual. Changes
requested on ECOs are described in the table below along with a description of how the request was handled at
this time.
ECO for Change to Part Number(s)
Revision Level Affected
V2982 204456
Rev. M
V3126 204482
Rev. N
V5263
Rev. P

TECHNICAL DATA

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . 2 cfm per gallon pumped (0.9 m#/hour/liter)
with pump operated within recommended range
. . . . . . . . . . 2–4 cfm (5.4–6.8 m#/hr) for continuous duty
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . Steel, Aluminum, Leather, Iron, Nitrile Rubber,
Acetal homopolymer, Ultra High Molecular Weight Polyethylene,
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Thiokolr is a registered trademark of the Thiokol Chemical Corporation.
IMPORTANT INFORMATION
Description of Change
Revise plumbing on air control to use inlet/outlet ports.
Solution: See notes on illustration on page 12 describing changes to
the configuration of the plumbing on the air control. The following
changes were made to the parts list on page 13:
Item 55 100628 – deleted
Item 56 100721 – quantity changed to 2
Item 58 100361 changed to 162449
Change screws on agitator, current screws are too short.
1. Change 100014 (1/4–20x5/8") to 100058 (1/4–20x3/4")
2. Change 100270 (1/4–20x1–1/4") to 100022 1/4–20x1–1/2")
Solution: Part numbers changed on item numbers 85 and 88 on page 15
The illustration of the agitator (204482) on page 14 shows a bearing that
is not on the print.
Solution: Bearing has been eliminated from the illustration on page 14.
40 –180 psi (3 – 12 bar)
. . . . . . . . . . . . . . . . . 100 cycles per minute
2 gpm (7.6 liter/min)
PTFE, Leather/Thiokolr
360 psi (25 bar)
54 (14)
1/4 npt(f)
1/2 npt(f)
3/8 npt(f)
3/4 npt(f)
306560 17