Table of Contents
Advertisement
Temperature Sensor(s) - Hood Mounting,
3 . Place the J-box plate inside of the octagon extension
ring and place over the hole .
4 . Disassemble the compression seal and place through
CAD Drawing from Tyler Schilling
hole and J-box plate as shown . Tighten the nut inside
Emailed to Barb on March 22, 2011
the octagon extension ring .
Updated the PN of the Resistive Temperature Detector to 384925 as provided in edits from Aaron Van Krey - October 18, 2012
Compression Seal
Updated the for the Digital Temperature Interlock IOM - edits provided by Aaron Van Krey - November 20, 2016
PN 463570
Gasket
Exploded View (Components)
CUT A 0.75" - 0.875" HOLE IN THE FLAT SPOT OF THE
1
PLACE THE J-BOX PLATE INSIDE OF THE OCTAGON EXTENSION
5 . Place the temperature sensor through the
CAPTURE TANK OF THE HOOD. KEEP 12" AWAY FROM
RING, AND PLACE OVER HOLE.
ANY LIGHT FIXTURE.
compression seal and tighten the compression fitting
DISASSEMBLE THE COMPRESSION SEAL AND PLACE THROUGH
THROUGH HOLE AND J-BOX PLATE AS SHOWN. TIGHTEN THE NUT
to 35 ft .-lbs . (47 .5 Nm) .
INSIDE THE OCTAGON EXTENSION RING.
0.75 to 0.875 inch
(19.0 to 22.2 mm)
diameter hole
Exhaust Area
Sensor Install
(cutout area)
Supply Area
Additional Octagon Extension
(optional)
1
CUT A 0.75" - 0.875" HOLE, CENTERED LEFT TO RIGHT
(Optional)
TITLE
AND 2" FROM THE BOTTOM.
PN 830125
HOOD PLAN VIEW
1.
PLACE THE THERMOSTAT THROUGH THE COMPRESSION
6 . Wire the sensor . Refer to Electrical Connections
3
COMPRESSION SEAL AND TIGHTEN THE COMPRESSION FITTING.
section for instructions on wiring the temperature
2.
INSTALL THE COVER FOR THE OCTAGON BOX.
sensor .
7 . Place octagon cover onto J-box and fasten it .
Sensor
PN 384925
1.
PLACE THE THERMOSTAT THROUGH THE
COMPRESSION SEAL AND TIGHTEN THE
COMPRESSION FITTING.
2.
INSTALL THE COVER FOR THE OCTAGON BOX.
4
Kitchen Fan Control Center
Octagon Extension
PN 830125
J-Box Plate
PN 732396
0.75 to 0.875 inch
(19.0 to 22.2 mm)
diameter hole
Hood Surface
3 inch air space
2 inches
(76.2 mm)
(50.8 mm)
Temperature Sensor
2 inch typical
PN 384925
(50.8 mm)
Hood Exhaust Collar
Front Side
DRAWN BY
MROCZENSKI_L
DATE
P.O.BOX 410 SCHOFIELD, WISCONSIN 54476-0410
12/02/2009
SUPERSEDES
INSTR, ADJ. TEMP
Octagon Cover
SCALE
INTERLOCK IN FLAT
PN 380926
CAD DRAWING NO.
SPOT
Octagon Cover
PN 380926
Additional Octagon
Extension
(Optional)
PN 830125
Temperature Sensor(s) - Duct Collar Mounting
continued
1 . Locate the exhaust duct on top of the hood . Find a
spot to mount the sensor where it will not interfere
CAD Drawing from Tyler Schilling
with fire suppression nozzles or other items installed
Emailed to Barb on March 22, 2011
in the ducts . If an exhaust fire damper is present in
Updated the PN of the Resistive Temperature Detector to 384925 as provided in edits from Aaron Van
the hood exhaust collar, it must be removed prior
Updated the for the Digital Temperature Interlock IOM - edits provided by Aaron Van Krey - November
to temperature sensor installation . A 3/4 to 7/8-inch
(19 .0 to 22 .2 mm) diameter hole must be cut into the
duct 2 inches (50 .8 mm) above the hood top .
0.75 to 0.875 inch
(19.0 to 22.2 mm)
diameter hole
Lock Washer
Nut
2 . Place the J-box plate inside of the octagon extension
1
CUT A 0.75" - 0.875" HOLE, CENTERED LEFT TO RIGHT
ring and place over the hole in the exhaust collar .
AND 2" FROM THE BOTTOM.
3 . Disassemble the compression seal and place through
hole in duct collar and J-box plate as shown . Tighten
CAD Drawing from Tyler Schilling
1.
PLACE THE J-BOX PLATE INSIDE OF THE OCTAGON EXTENSION
2
the nut inside the octagon extension ring .
RING, AND PLACE OVER HOLE.
Emailed to Barb on March 22, 2011
2.
DISASSEMBLE THE COMPRESSION SEAL AND PLACE THROUGH
Updated the PN of the Resistive Temperature Detector to 384925 as provided in edits
THROUGH HOLE AND J-BOX PLATE AS SHOWN. TIGHTEN THE NUT
INSIDE THE OCTAGON EXTENSION RING.
Updated the for the Digital Temperature Interlock IOM - edits provided by Aaron Van K
19.525 inches
(495.9 mm)
Exhaust Area
Sensor
PN 384925
ECO
Sensor Install
IAN29890
(cutout area)
ENG. REF.
1.
PLACE THE THERMOSTAT THROUGH THE
3
1/4
COMPRESSION SEAL AND TIGHTEN THE
B
COMPRESSION FITTING.
2.
INSTALL THE COVER FOR THE OCTAGON BOX.
4 . Place the temperature sensor through the
HOOD PLAN VIEW
compression seal and tighten the compression fitting
1
to 35 ft .-lbs . (47 .5 Nm) .
1.
PLACE THE J-BOX PLATE INSIDE OF THE
2
OCTAGON EXTENSION RING, AND PLACE OVER
HOLE IN THE EXHAUST COLLAR.
2.
DISASSEMBLE THE COMPRESSION SEAL AND PLACE
THROUGH HOLE IN DUCT COLLAR AND J-BOX
PLATE AS SHOWN. TIGHTEN THE NUT INSIDE THE
OCTAGON EXTENSION RING.
5 . Wire the sensor . Refer to Electrical Connections
3
section for instructions on wiring the temperature
sensor .
6 . Place octagon cover onto J-box and fasten it .
Compression Seal
PN 463570
Gasket
2 inches
(50.8 mm)
Hood Exhaust Collar
Front Side
Octagon Cover
PN 380926
1/4-inch Compression Seal
PN 463570
Additional Octagon
Octagon Extension
Extension
PN 830125
(Optional)
Quik Seal
3 inch air space
PN 830125
Gasket
(76.2 mm)
2 inch typical
0.75 to 0.875 inch
(50.8 mm)
(19.0 to 22.2 mm)
diameter hole
Supply Area
(optional)
TITLE
Exploded View (Components)
INSTR, ADJ. TEMP
INTERLOCK IN FLAT
CUT A 0.75" - 0.875" HOLE, CENTERED LEFT TO RIGHT
AND 2" FROM THE BOTTOM.
Additional Octagon
Extension
(Optional)
PN 830125
P.O.BOX 410 SCHOFIELD, WISCONSIN 54476-0410
TITLE
INSTR, ADJ. TEMP
Sensor
PN 384925
INTERLOCK IN DUCT
COLLAR
1.
PLACE THE THERMOSTAT THROUGH THE
COMPRESSION SEAL AND TIGHTEN THE
COMPRESSION FITTING.
2.
INSTALL THE COVER FOR THE OCTAGON BOX.
Octagon Extension
PN 830125
J-Box Plate
PN 732396
Lock Washer
Nut
1.
PLACE THE J-B
2
OCTAGON EXTE
HOLE IN THE EX
2.
DISASSEMBLE
THROUGH HOL
PLATE AS SHOW
J-Box Plate
OCTAGON EXTE
PN 732396
2 inches
Lock Washer
(50.8 mm)
Nut
DRAWN BY
MROCZENSKI_L
DATE
P.O.BOX 410 SCHOFIELD, WISCONSIN 54476-0410
12/02/2009
Hood Exhaust Collar
SUPERSEDES
Front Side
SCALE
1/4
CAD DRAWING NO.
SPOT
Octagon Cover
PN 380926
DRAWN BY
ECO
MROCZENSKI_L
IAN29890
DATE
ENG. REF.
12/02/2009
SUPERSEDES
SCALE
1/4
CAD DRAWING NO.
B
®
ECO
IAN29890
ENG. REF.
B
1
2
2
Advertisement
Table of Contents
