Table of Contents
Advertisement
Installation
Control Box Mounting
Control box may be factory mounted . If so, continue
to the next section .
CUT A 0.75" - 0.875" HOLE IN THE FLAT SPOT OF THE
1
Locate an area with enough space to mount the control
CAPTURE TANK OF THE HOOD. KEEP 12" AWAY FROM
ANY LIGHT FIXTURE.
box and fasten to the wall . Use appropriate type
fasteners depending on the mounting location . Avoid
installing the control box in environments with high
magnetic and/or radio frequency interference .
Switch Mounting
If the switches were NOT shipped loose, provided in a
separate junction box, continue to the next section .
Locate an area with enough space to mount the
switches junction box and fasten to the wall .
Additional Octagon Extension
(Optional)
PN 830125
1.
PLACE THE THERMOSTAT THROUGH THE COMPRESSION
3
COMPRESSION SEAL AND TIGHTEN THE COMPRESSION FITTING.
2.
INSTALL THE COVER FOR THE OCTAGON BOX.
®
0.75 to 0.875 inch
(19.0 to 22.2 mm)
diameter hole
NOTE
Hood Surface
Temperature Sensor
NOTE
PN 384925
Octagon Cover
PN 380926
3
Temperature Sensor(s) - Hood Mounting
Temperature sensor(s) will be provided only if the
digital temperature interlock option was configured/
ordered with the unit . If it wasn't, continue to the next
section .
Temperature sensor(s) may be factory installed . If so,
1.
PLACE THE J-BOX PLATE INSIDE OF THE OCTAGON EXTENSIO
2
RING, AND PLACE OVER HOLE.
continue to the next section .
2.
DISASSEMBLE THE COMPRESSION SEAL AND PLACE THROUG
THROUGH HOLE AND J-BOX PLATE AS SHOWN. TIGHTEN THE
1 . Locate flat area(s) at the top interior of the hood in
INSIDE THE OCTAGON EXTENSION RING.
front of the filters, towards the front of the hood .
19.525 inches
(495.9 mm)
Top View of Exhaust Hood
CAD Drawing from Tyler Schilling
2 . Find a spot for the sensor in the flat space that will
Emailed to Barb on March 22, 2011
not interfere with the fire suppression nozzles and
Updated the PN of the Resistive Temperature Detector to 384925 as provided in edits from A
that is not within 12 inches (304 .8 mm) of any light
Updated the for the Digital Temperature Interlock IOM - edits provided by Aaron Van Krey - N
fixtures . Cut a 3/4 to 7/8-inch (19 .0 to 22 .2 mm)
diameter hole in the flat spot of the capture tank .
Hood Surface
CUT A 0.75" - 0.875" HOLE IN THE FLAT SPOT OF THE
1
CAPTURE TANK OF THE HOOD. KEEP 12" AWAY FROM
ANY LIGHT FIXTURE.
Additional Octagon Extension
(Optional)
PN 830125
Octagon Cover
PN 380926
1.
PLACE THE THERMOSTAT THROUGH THE COMPRESSION
COMPRESSION SEAL AND TIGHTEN THE COMPRESSION FITTING.
2.
INSTALL THE COVER FOR THE OCTAGON BOX.
NOTE
Exhaust Area
Sensor Install
(cutout area)
Supply Area
(optional)
TITLE
HOOD PLAN VIEW
0.75 to 0.875 inch
(19.0 to 22.2 mm)
diameter hole
Temperature Sensor
PN 384925
Kitchen Fan Control Center
3 inch air space
(76.2 mm)
2 inch typical
(50.8 mm)
P.O.BOX 410 SCHOFIELD, WISCONSIN 54476-041
INSTR, ADJ. TEMP
INTERLOCK IN FLAT
SPOT
1.
PLACE THE J-BO
2
RING, AND PLAC
2.
DISASSEMBLE T
THROUGH HOLE
INSIDE THE OCT
19.525 inches
(495.9 mm)
Exhaust Area
Sensor Install
(cutout area)
Supply Area
(optional)
HOOD PLAN VIE
3
Advertisement
Table of Contents
