Advertisement
Quick Links
LCD PROJECTOR
LENS REPLACEMENT AND INSTALLATION PROCEDURES
When installing or replacing the Projection Lens, refer to this manual. For
installation of the lens, use the parts designated in the manual. Do not use the
installation manual and Light-Block Sheets in the lens package.
Check the following parts supplied to this projector.
AVAILABLE LENS
This projector applies the Projection Lenses listed below. Use the suitable lens for
where the projector is used.
Model NO.
38-809036-02
38-809041-02
38-809042-02
38-809037-02
38-809043-02
38-809040-02
38-809038-02
38-809039-02
38-809044-02
Lens installation and replacement should be made by the qualified service
personnel.
Be sure to install the lens following this procedure precisely.
Do not touch or remove any parts except the lens and related parts. It may
result in malfunctions, electrical shock, fire hazard or other accidents.
Before installing or replacing the lens, check that the Model No. of the
Projection Lens matches to the projector.
When moving or setting up the projector, be sure to replace the Lens Cover
to protect the surface. And be careful not to hold or subject the lens to
strong forces. It may damage the lens, cabinet, or mechanical parts.
For details of the lens and installation, contact the sales dealer where you
purchased the projector.
1AA6P1P3900-- (MC7K)
CAUTION
LIGHT-BLOCK SHEETS
LENS ATTACHMENT (01) 1 pce.
LENS ATTACHMENT (02) 1 pce.
Type
Fixed Short Throw Lens
Fixed Long Throw Lens
Long Throw Zoom Lens
Short Throw Zoom Lens I
Short Throw Zoom Lens II
Semi-Long Throw
Zoom Lens
Standard Zoom Lens I
Standard Zoom Lens II
Standard Zoom Lens III
NOTES ON LENS INSTALLATION
- 1 -
6 pcs.
Zoom
Focus
Fixed
Manual
Fixed
Manual
Motor Driven
Motor Driven
Motor Driven
Motor Driven
Fixed
Manual
Motor Driven
Motor Driven
Motor Driven
Motor Driven
Motor Driven
Motor Driven
Motor Driven
Motor Driven
Advertisement
Related Manuals for Christie LX1500
Summary of Contents for Christie LX1500
- Page 1 LCD PROJECTOR LENS REPLACEMENT AND INSTALLATION PROCEDURES CAUTION When installing or replacing the Projection Lens, refer to this manual. For installation of the lens, use the parts designated in the manual. Do not use the installation manual and Light-Block Sheets in the lens package. Check the following parts supplied to this projector.
-
Page 2: Cover Plate
LENS REPLACEMENT AND INSTALLATION PROCEDURE NOTE : The installation procedure and needed parts for lens installation depend on the type of the Projection Lens. Check the Model No. of the Projection Lens and be sure to install or replace the lens following procedure below. -
Page 3: Lens Attachment
Replace Lens Cap on the rear (mounting side) of Projection Lens and mount Lens on the lens Attachment with 4 Screws. (Use screws attached on lens.) Connect the Lens Motor Lead connector to the socket on the right-top of the lens attachment. (Motor Driven Lens only.) See Fig. - Page 4 This projector has 6 Light-Block Sheets. Use 2 Light-Block Sheets corresponding with lens. (Refer to the list below.) Use 1 Light-block Sheet for MODEL 38-809043-02 Set 2 Light-Block Sheets through the lens. Make sure the shape of the Light-Block Sheets are correct and be sure to set them as shown in the Fig. 8. NOTE: Be sure to set each Light-Block Sheet as shown in Fig-8.
- Page 5 Adjust focus of the Projection Lens. (38-809036-02, 38-809041-02 and 38-809043-02 only.) Set up the projector and project image on the screen. Loosen Focus Lens Lock Screw and rotate Projection Lens to obtain proper focus. After adjusting focus, be sure to lock Projection Lens with Focus Lens Lock Screw securely.
- Page 6 FOCUS ADJUSTMENT (For Model 38-809043-02) Set up the projector and project image on the screen. 1. Loosen the Focus Lock Screw on the projection lens. mark (yellow) 2. Rotate the projection lens to obtain proper focus on center area of the screen. When the distance of the screen and lens is 1 meter, mark (yellow) of the lens on Focus Lock Screw position.
- Page 7 - 7 -...