Table of Contents
Advertisement
Available languages
Available languages
Secure the Drain Hose
1. Drape the power cord over the washer top.
2. Secure the drain hose to the laundry tub leg or standpipe with
the beaded strap provided. (See illustrations 1 and 2.)
1
If the washer faucets and the drain standpipe are recessed
(see illustration 3), put the hooked end of the drain hose in the
standpipe. Tightly wrap the beaded strap around the water
inlet hoses and the drain hose.
Do not force excess drain hose into the standpipe.
Level the Washer
Properly leveling your washer prevents excessive noise and
vibration.
1. Check the levelness of the washer by placing a level on the
top edge of the washer, first side-to-side, then front-to-back.
If the washer is against a wall, move the washer out slightly
before tipping back. If the washer is not level, first prop the
front with a wood block (2" x 4") and adjust the feet as
necessary; then prop the back and adjust feet as necessary.
Repeat this step until washer is level.
2. After the washer is level, use a
wrench to turn the nuts on the feet tightly against the washer
cabinet.
All 4 feet must be tightened. If the nuts are not tight against
the washer cabinet, the washer may vibrate.
3. Slide the washer to its final location.
4. Confirm the levelness of the washer.
8
2
3
in. (17 mm) open-end
Complete Installation
1. Check the electrical requirements. Be sure that you have the
correct electrical supply and the recommended grounding
method. (See "Electrical Requirements.")
2. Check to be sure all parts are now installed. If there is an
extra part, go back through the steps to see which step was
skipped.
3. Check to be sure you have all of your tools.
4. Dispose/recycle all packaging materials.
5. Check to be sure the water faucets are on.
6. Check for leaks around faucets and inlet hoses.
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in
death, fire, or electrical shock.
7. Plug into a grounded 3 prong outlet.
8. Read "Washer Use."
9. To test and to clean your washer, measure
recommended amount of powdered or liquid High Efficiency
(HE) detergent or ¼ the normal recommended amount of
regular powdered or liquid detergent. Pour the detergent into
the detergent dispenser. Select NORMAL/CASUAL, and then
select HOLD TO START. Allow the washer to complete one
whole cycle.
the normal
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the duet Front-Load Washer and is the answer not in the manual?
Questions and answers
where is and how to clean lint trap whirlpool duet frontend loader
How to use the spin cycle only
To use the spin cycle only on a Whirlpool Duet Front-Load Washer, follow these steps:
1. Select PAUSE/CANCEL to stop any current cycle.
2. Select DRAIN/SPIN on the control panel.
3. Press and hold HOLD TO START for about 1 second to begin the spin cycle.
4. When the spin is complete, the door will unlock, and you can remove the items.
If needed, you can reduce the spin speed by selecting the desired speed from the SPIN SPEED modifier.
This answer is automatically generated
is there a way to have a shorter cycle than 27 minutes? Please instruct.
The Whirlpool Duet Front-Load Washer has a Quick Wash cycle designed for loads that are needed in a hurry. This cycle combines fast-speed tumbling, a shortened wash time, and high-speed spin to shorten drying time. However, the exact duration of the Quick Wash cycle is not specified in the provided information. If the Quick Wash cycle is shorter than 27 minutes, then the washer can have a shorter cycle.
This answer is automatically generated