Advertisement
INSTALLATION GUIDELINE
1. Prepare the Site :-
• Rough-in the supplies & the drain piping. For dimensions, Refer Fig.#2.
• Install 1/2" water supply lines & 1-1/4" drain piping according to the roughing-in information.
• Install sufficient backing behind the finished wall to provide a secure material for the anchoring devices.
NOTE :- The Angle-Valve handles cannot extend more than 76mm (3") from the finished wall when in open position. This will
ensure the handles will not touch the pedestal when fully open.
2. Installation of the Lavatory :-
WALL-MOUNT
• Drill two
14mm Anchor holes on the wall as
Ø
shown in the Rough-in diagram.
• Insert the plastic anchors (provided) in two
holes.
• Insert the metal studs (provided) into these
plastic anchors using an adjustable wrench.
• Ensure that at least 70 mm (approx.) of each
stud should remain exposed from the wall.
Refer Fig. #3
• Install the faucet & drain to the lavatory
according to the manufacturer's instructions.
NOTE :- Do not fully tighten slip-joint drain
connections at this time.
Refer Fig. #4
• Carefully place the lavatory against the wall,
so the metal studs extend through the
lavatory holes.
• Level the lavatory.
• Install the plastic washer & nut (provided)
& tighten suitably.
CAUTION : Risk of product damage.
Do not over tighten the nut. Over tightening
may cause damage to the product.
*
U se wrench to tighten 8-10 N-m/ 6-9 turns.
(1 turn = 45°) past finger tight.
Refer Fig. #5
• Connect & tighten the bottle trap as per
manufacturer's instructions. Connect the
hot & cold water supplies to the faucet.
• Evenly p
ut the sealant around the mounting
surface of the lavatory touching the wall.
• Clean the lavatory top.
Refer Fig. #6
* Installation doesn't allow use of any tool other than standard wrench.
For this reason, split turns have been mentioned rather than full turns.
SERVICE PARTS
A. Hardware Kit 1213117
B. Levelling Pads 63069
Important Notice for Care, Cleaning & Daily use
To keep your lavatory looking new, make sure you rinse it out thoroughly after each use.
DO NOT USE ABRASIVES on this product, as they will scratch & ruin the surface.
Stubborn stains, paint, or tar can be removed with turpentine or paint thinner.
1213118-IN01-C
3
Plastic Anchors
Metal Studs
4
5
Metal Studs
Plastic Washer
6-9 turns (45
° each
) allowed past finger tight
6
(Supplied with the Product)
FULL-PEDESTAL
• Apply two self-adhesive levelling pads (provided)
to each of the three ridges in the bottom recess of the
lavatory. Refer Fig. #7
• Mark the centerline on the floor with a pencil.
• Position the pedestal on the floor centerline location.
Refer to the roughing-in dimensions for correct
placement.
• Carefully set the lavatory on the pedestal.
• Move the pedestal as required to ensure proper
fit in the desired location.
• Level the lavatory. Use additional self-adhesive
levelling pads as required to level the lavatory.
NOTE :-The lavatory must be supported by the
pedestal.
• Check the lavatory placement.
• Mark the center of each anchoring hole on the wall.
• Carefully remove the lavatory from the pedestal. Then
move the pedestal from the area.
Refer Fig. #8
Drill two
14mm Anchor holes at the marked location
•
Ø
on the wall.
• Insert the plastic anchors in two holes.
• Insert the metal studs (provided) into these plastic
anchors using an adjustable wrench.
• Ensure that at least 70 mm (approx.) of each stud
should remain exposed from the wall.
Refer Fig. #9
Lavatory
Install the faucet & drain to the lavatory according
•
to the manufacturer's instructions.
NOTE :- Do not fully tighten slip-joint drain
Nut
connections at this time.
Refer Fig. #10
Place the pedestal to its original location.
•
Set the lavatory on the pedestal so the metal
•
studs extend through the lavatory holes.
45°
• Level the lavatory.
• Install the washer & nut & tighten suitably.
CAUTION : Risk of product damage.
Do not over tighten the nut. Over tightening
may cause damage to the product.
*
Use wrench to tighten 8-10 N-m/ 6-9 turns.
(1 turn = 45°) past finger tight.
Refer Fig. #11
Connect & tighten the trap as per manufacturer's
•
instructions. Connect the hot & cold water supplies
to the faucet.
Evenly put the sealant around the mounting
•
surface of the lavatory touching the wall.
• Clean the lavatory top.
Refer Fig. #12
-2-
7
8
Pedestal
Mark Floor
Here
Center of
Anchoring Holes
9
Plastic
Anchors
Metal Studs
10
11
Metal Studs
Lavatory
Plastic Washer
6-9 turns (45
° each
) allowed past finger tight
12
Toll Free 1800 103 2244
Nut
45°
in
Advertisement
