Table of Contents
Advertisement
P R E-O P E R AT I O N C H E C K L I S T
5.13
Check for missing or loose bolts. Tighten loose bolts and
replace missing bolts before operating machine. Verify that belt and
blade guards are in place. Never operate a MARK III without guards in
place. See Figure 14 and Figure 15.
4.0
5.14
WARNING: If you can see the drive belt or diamond blade,
the guards are not in place. Never operate a MARK III without guards
in place. The proper position for the belt guard is bolted with four bolts
to the chassis. The proper position for the blade guard is down with the
Read and understand
operator's manual before
white guard dust brush touching the horizontal surface. See Figure 14
using this machine.
and Figure 15.
Failure to follow operating
Instructions could result
5.15
Dress properly. Wear ear and eye protection. See sections 4.3
in injury or damage to
equipment.
through 4.7. See Figure 16
WARNING
5.16
WARNING: TO PREVENT SERIOUS INJURY DO NOT OPERATE SAW
WITHOUT PROPER TRAINING.
Avoid injury.
Do NOT operate with
guard removed.
Replace guard before
Avoid injury.
Figure 6 - Warning label - do not operate with
operating machine.
Do NOT operate with
guard removed.
Replace guard before
operating machine.
4.0
Rules for safer operation
Rotating blade
hazard.
Do NOT operate with
guard up.
Read and understand
Keep hands and feet
operator's manual before
away.
using this machine.
Failure to follow operating
Instructions could result
Figure 7 - Warning label - do not operate with guard
in injury or damage to
equipment.
This product can expose you to chemicals, including NICKEL. When used, serviced, cleaned, or maintained equipment could generate particulates
This product can expose you to chemicals, including NICKEL. When used, serviced, cleaned, or maintained equipment could generate particulates
that contain chemicals, including silica. These chemicals are known to the state of California to cause cancer and birth defects or other
hat contain chemicals, including silica. These chemicals are known to the state of California to cause cancer and birth defects or other
reproductive harm. For more information, visit
eproductive harm. For more information, visit
WARNING
Flying debris
and loud noise
hazards. Wear
ear and eye
protection
Figure 8 - Warning label - wear proper clothing, ear and eye protection
Read and understand
operator's manual before
using this machine.
Failure to follow operating
Instructions could result
in injury or damage to
equipment.
WARNING
Rules for safer operation
5400 MAX. RPM
C1 hazard Communication Sywems. L L L L C C
Rotating blade hazard.
Do NOT operate with guard up.
Keep hands and feet away.
To avoid injury:
Always inspect saw
blades before use.
Replace all cracked or damaged
To avoid injury:
blades.
guard removed
Always inspect saw
blades before use.
Replace all cracked or damaged
blades.
AVOID INJURY.
Rotating blade
hazard.
Do NOT operate with guard removed.
Replace guard before operating
Do NOT operate with
machine.
guard up.
Keep hands and feet
Use only diamond blades (steel
away.
centered diamond cutting-off
wheels) with this machine. RPM
rating on blade must exceed
machine max rpm rating. The use
of any other blade could result in
up
death or serious injury.
www.P65Warnings.ca.gov
www.P65Warnings.ca.gov
Wear appropriate clothing
5400 MAX. RPM
C1 hazard Communication Sywems. L L L L C C
M M O O - - 7 7 4 4 6 6 - - 0 0 2 2 4 4 1 1
Surface Prep
Division
Use only diamond blades (steel
centered diamond cutting-off
wheels) with this machine. RPM
rating on blade must exceed
machine max rpm rating. The use
of any other blade could result in
death or serious injury.
WARNING: Recommended accessories for this tool including blades are
listed in this manual or are available by calling customer service. The use of
any other attachment or accessory might be hazardous
5.17
MARK III premium dry cut diamond blades, medium bond
5400 MAX. RPM
Use only diamond blades (steel
DEPTH OF
centered diamond cutting-off
wheels) with this machine. RPM
JOINT
C1 hazard Communication Sywems. L L L L C C
M M O O - - 7 7 4 4 6 6 - - 0 0 2 2 4 4 1 1
rating on blade must exceed
machine max rpm rating. The use
of any other blade could result in
Up to 2"
death or serious injury.
Deep
Up to 3"
Deep
M M O O - - 7 7 4 4 6 6 - - 0 0 2 2 4 4 1 1
DEPTH OF
JOINT
Up to 2"
Deep
Up to 3"
Deep
Engine exhaust
DEPTH OF
contains poisonous
JOINT
c c a a r r b b o o n n m m o o n n o o x x i i d d e e g g a a s s . .
Engine exhaust
Breathing it could cause
Up to 2"
contains poisonous
death.
c c a a r r b b o o n n m m o o n n o o x x i i d d e e g g a a s s . .
Deep
Breathing it could cause
Operate machine in well
death.
ventilated area.
Operate machine in well
ventilated area.
Up to 3"
Deep
(* All blades listed are designed with MARK III drive pin holes and
JOINT WIDTH (INCHES)
SIZE
1/8 - 3/16
3/16 - 3/8
8"
.095
.125
.187
.187
HARD
HARD
.095
.125
.187
10"
.187
HARD
JOINT WIDTH (INCHES)
SIZE
1/8 - 3/16
3/16 - 3/8
8"
.095 x 8
.187 x 8
.125 x 8
.250 x 8
.187 x 8
.375 x 8
MEDIUM
MEDIUM
10"
.095 x 10
.187 x 10
.125 x 10
.250 x 10
.187 x 10
.375 x 10
MEDIUM
MEDIUM
JOINT WIDTH (INCHES)
SIZE
1/8 - 3/16
3/16 - 3/8
8"
.095 x 8
.187 x 8
.125 x 8
.250 x 8
.187 x 8
.375 x 8
SOFT
SOFT
10"
.095 x 10
.187 x 10
.125 x 10
.250 x 10
.187 x 10
.375 x 10
SOFT
SOFT
Table 6 - Dry cut diamond blade list
1" diameter arbor holes.)
P: 877-817- 6687 F: 813-621-7125
Visit us at www.ussaws.com
sales@ussaws.com
3/8 - 1/2
1/2 or more
.250
.375
.500
.095 +
.375
spacers
HARD
HARD
.250
.375
.500
.095
plus
spacers
.375
HARD
HARD
3/8 - 1/2
1/2 or more
.375 x 8
.095 + .060
.500 x 8
spacer x 8
.
MEDIUM
MEDIUM
.375 x 10
.095 + .060
.500 x 10
spacer x 10
MEDIUM
MEDIUM
3/8 - 1/2
1/2 or more
.375 x 8
.095 + .060
.500 x 8
spacer x 8
SOFT
SOFT
.375 x 10
.095 + .060
.500 x 10
spacer x 10
SOFT
SOFT
8
Advertisement
Table of Contents
