Table of Contents
Advertisement
Quick Links
Arc
CBS
Safe
®
A Group CBS Company
U S E R S M A N UA L
RSK-ABL1
Remote Operator for Allen Bradley Centerline
Motor Control Center Units
WE
WHAT STANDS
BETWEEN YOU
DO.
AND ARC-FLASH
DANGER ?
CBSArcSafe.com |
Email: info@CBSArcSafe.com
| 877-4-SAFETY |
Fax: 940-382-9435
Rev. August 2019
Advertisement
Table of Contents
Related Manuals for CBS ArcSafe RSK-ABL1 Series
Summary of Contents for CBS ArcSafe RSK-ABL1 Series
- Page 1 Safe ® A Group CBS Company U S E R S M A N UA L RSK-ABL1 Remote Operator for Allen Bradley Centerline Motor Control Center Units WHAT STANDS BETWEEN YOU AND ARC-FLASH DANGER ? CBSArcSafe.com | Email: info@CBSArcSafe.com | 877-4-SAFETY | Fax: 940-382-9435 Rev.
- Page 2 Safe ® A Group CBS Company User’s Manual for the following RSK models: RSK-ABL1-C and RSK-ABL1-W • 1.0 Introduction • 2.0 General Safety Information 2.1 Arc-Blast Hazards 2.2 Battery Hazards 2.3 Magnet Hazards 2.4 Pinch Point Hazards 2.5 Radio Frequency •...
- Page 3 Do not ship damaged lithium batteries. OR ARC FLASH Please contact CBS ArcSafe at the address in Section 8.0 • This equipment must only be installed by if you need more information on the battery pack.
-
Page 4: Radio Frequency
Safe ® A Group CBS Company • Do not attempt to service the magnets. There are no user • Turning the magnets to the “ON” position prior serviceable parts inside the device. to installing the RSK-ABL1 could cause a quick uncontrollable attraction to ferromagnetic materials in •... - Page 5 Both types of battery packs are custom designed to work with the RSK-ABL1 and are only available through CBS ArcSafe. Use only approved battery packs. CBS ArcSafe can provide assistance to assure that you order the correct battery. See Section 8.0 for information to contact CBS ArcSafe.
- Page 6 Safe ® A Group CBS Company STEP 3: Disconnect battery at connector. STEP 6: Replace battery cover. STEP 4: Plug new battery into the connector and slide 3.2 Replacing the Battery in battery into place. NOTE: The battery will only go in Wireless Remote Transmitter one way.
- Page 7 Safe ® A Group CBS Company 4.0 Use and Operation of the RSK-ABL1 The RSK-ABL1 can be installed over the MCC operating handle regardless of the position of the handle (whether it is in the ON or OFF position). Care must be taken when installing RSK-ABL1 that the MCC handle is not inadvertently operated. The RSK-ABL1 is designed to work without modification on the three different types of operating handles shown below.
- Page 8 Safe ® A Group CBS Company STEP 3: With actuator now flush against the MCC STEP 2: While standing at a safe distance, press and hold door, twist each magnet lever one-half turn clockwise the ENABLE button on the hand-held controller. The yellow to lock the magnets and actuator in place.
-
Page 9: Specifications
Safe ® A Group CBS Company 5.0 Storage 7.0 Specifications The RSK-ABL1 is provided with a heavy duty carrying case Voltage RSK-ABL1 – 22.5VDC and 3.0VDC (custom that can be used to conveniently store the actuator and its designed battery available in Lithium or Alkaline. - Page 10 ® A Group CBS Company Worldwide Headquarters & U.S. Sales U.K. /Europe Office CBS ArcSafe, Inc. A Group CBS Company 27 Cressey Avenue | Shenley Brook End 2616 Sirius Road | Denton, TX 76208 Milton Keynes, Buckinghamshire Ph: 877-4-SAFETY | Ph: 940-382-4411 | Fx: 940-382-9435...