Advertisement
Enable Synch
Light Synch
Aux Synch
Stpt Shift Sync
Use Remote Disp
SETPOINT STATUS Set point status
LIGHTS OUTPUT
DEFROST END
PROBE 1 TEMP
PROBE 2 TEMP
PROBE 3 TEMP
PROBE 4 TEMP
FAN PROBE
DIGITAL INPUT 1
DIGITAL INPUT 2
DIGITAL INPUT 3
COMPRESSOR 1
COMP 1 SAFETY
Document Part # 026-4275 Rev 0
©2019 Emerson Climate Technologies Retail Solutions, Inc. This document may be photocopied for personal use.
Visit our website at http://www.emerson.com for the latest technical documentation and updates.
LOF - LAN enable input
synchronization
Lli - LAN light output
synchronization
LAU - LAN aux output
synchronization
LES - LAN setpoint shift
synchronization
LSd - Use display from LAN Not used.
Reports light relay output
status
Defrost End State
dP1 - Probe 1 temperature Reports temperature probe 1 status on application status screen. Update
dP2 - Probe 2 temperature Reports temperature probe 2 status on application status screen. Update
dP3 - Probe 3 temperature Reports temperature probe 3 status on application status screen. Update
dP4 - Probe 4 temperature Reports temperature probe 4 status on application Status screen. Update
Evaporator Fan Probe
Value
Reports digital input state
1
Reports digital input state
2
Reports digital input state
3
Reports comm 1 relay
output status
Reports status if comp 1
safety dig input
Table 2 - XM670K_50 Property Help Explanations
Not used.
Not used.
Not used.
Not used.
Reports active setpoint status on application Status screen. Update rate:
10 - 30 seconds. Can be pointed to for use in other applications. Logging
set by default. User can disabled logging.
Reports light relay output status on application Status screen. Update
rate: 10 - 30 seconds. Can be pointed to for use in other applications.
Logging set by default. User can disable logging.
Reports active setpoint status on application Status screen. Update rate:
10 - 30 seconds. Can be pointed out for use in other applications. Logging
set by default. User can disable logging.
rate: 10 - 30 seconds. Can be pointed out for use in other applications.
Logging set by default. User can disable logging.
rate: 10 - 30 seconds. Can be pointed out for use in other applications.
Logging set by default. User can disable logging.
rate: 10 - 30 seconds. Can be pointed out for use in other applications.
Logging set by default. User can disable logging.
rate: 10 - 30 seconds. Can be pointed out for use in other applications.
Logging set by default. User can disable logging.
Reports configured fan probe value. If not set, a reading of
-32768 will log. Can be pointed out for use in other applications. Logging
set by default. User can disable logging.
Reports digital input 1 status on application Status screen. Update rate: 10
- 30 seconds. Can be pointed out for use in other applications. Logging set
by default. User can disable logging.
Reports digital input 2 status on application Status screen. Update rate: 10
- 30 seconds. Can be pointed out for use in other applications. Logging set
by default. User can disable logging.
Reports digital input 3 status on application Status screen. Update rate: 10
- 30 seconds. Can be pointed out for use in other applications. Logging set
by default. User can disable logging.
Reports compressor 1 relay output status on application Status screen.
Update rate: 10 - 30 seconds. Can be pointed out for use in other
applications. Logging set by default. User can disable logging.
Reports compressor 1 safety digital input status on application Status
screen. Update rate: 10 - 30 seconds. Can be pointed out for use in other
applications. Logging set by default. User can disable logging.
Page 20 of 23
Advertisement
