Download Print this page

Siemens CERBERUS FIT Series Operation (Short

Fire control panel
Hide thumbs

Advertisement

Quick Links

www.siemens.com/buildingtechnologies
Operation (short)
FC120
Fire control panel (NL)
ALARM Procedure
with Alarm Verification Concept (AVC)
Alarm Verification Concept (AVC) – suggested possible procedure – subject to local requirements
Fire alarm
Zone 1
Zone 1
Meeting room 1
3.
4.
5.
B
Action / Condition
1.
Press
on the PMI
(V1) runs out (Password required)
2.
Read time of top line right side on the display
top line right side on the display
3.
Read fire location on display.
4.
Go to the fire location.
5.
Decide:
MAJOR INCIDENT
MAJOR
INCIDENT:
A
Press
o
r actuate nearest manual call point.
B
Look at the LED indicator
'On: Fire brigade called'
'Off: Call fire brigade!'
(Remote transmission is switched off / not
Remote transmission is switched off / not
available or defective)
Minor
incident:
R
Press
(Password required)
6.
Press
7.
Press
Document ID: A6V10393200_a_en_--
2.
2:00
2:00
1/1
1/1
Go to the fire location.
the fire location.
Decide:
MAJOR INCIDENT or
MAJOR INCIDENT or
Minor incident
.
before allowed
before allowed reaction time
or
minor
minor incident
incident.
<alarm delay off>
<alarm delay off>
manual call point.
to reset the panel.
to reset the panel.
twice.
twice.
ALARM-Procedure
Switching off detector zones
Switching on detector zones
Procedure in case of Fault
1.
R
Consequence / Status
Buzzer is turned off, alarm is acknowledged.
Buzzer is turned off, alarm is acknowledged.
Countdown V2 for the investigation of the cause of alarm starts.
2 for the investigation of the cause of alarm starts.
Remaining time is shown as countdown before Fire Brigade call.
Remaining time is shown as countdown before Fire Brigade call.
Information on the cause of ALARM
Information on the cause of ALARM
If required, initiate suitable emergency measures.
If required, initiate suitable emergency measures.
The remote transmission for fire alarm is activated immediately.
The remote transmission for fire alarm is activated immediately.
ALARM is transmitted to fire brigade.
ALARM is transmitted to fire brigade.
Fire brigade must be called by phone!
No automatic transmission to fire brigade
No automatic transmission to fire brigade
Dial the following no.:
Fire detection system is in normal condition unless another event
Fire detection system is in normal condition unless another event
occurs. It may be necessary to vent the room before resetting is
occurs. It may be necessary to vent the room
possible. Elements that cannot be reset c
possible. Elements that cannot be reset can be switched off
temporarily.
the evacuation.
Stop
the evacuation.
Start
Edition: 2013-07-24
Siemens Switzerland Ltd
Industry Sector
Building Technologies Division
International Headquarters
Gubelstrasse 22
CH-6301 Zug
subject to local requirements
A
phone!
Page 1
Page 2
Page 3
Page 4
7.
6.
1 / 4

Advertisement

loading

  Related Manuals for Siemens CERBERUS FIT Series

  Summary of Contents for Siemens CERBERUS FIT Series

  • Page 1 Siemens Switzerland Ltd Industry Sector Building Technologies Division International Headquarters Gubelstrasse 22 www.siemens.com/buildingtechnologies CH-6301 Zug ALARM-Procedure Page 1 Operation (short) Switching off detector zones Page 2 FC120 Fire control panel (NL) Switching on detector zones Page 3 Procedure in case of Fault...
  • Page 2: Switching Off Detector Zones

    Switching off detector zones (password required) The following example represents a possible operation sequence: WARNING System parts that have been switched off make it impossible to acquire and process alarms or faults! Fire may spread unhindered. Deploy staff to monitor the deactivated area. You must switch deactivated parts of the 'Site' back on as soon as possible.
  • Page 3 Switching on detector zones (Password required) When there is no event with a higher priority, isolations (switched off) are directly indicated on the display. You may then directly proceed with Step 3 below. Step Result Menu Press the button to open the main menu. Event summary (Password required) Enable / disable...
  • Page 4: Procedure In Case Of Fault

    Procedure in case of Fault Step Result Buzzer on the panel is switched off. is switched off. Press on the PMI. Read message/fault location on the display. on the display. Information on type and place of the fault. Information on type and place of the fault. Go to the fault location and remedy the cause of Go to the fault location and remedy the cause of When the fault has been eliminated,...
  • Page 5: Alarm Procedure

    Siemens Switzerland Ltd Industry Sector Building Technologies Division International Headquarters Gubelstrasse 22 www.siemens.com/buildingtechnologies CH-6301 Zug ALARM-Procedure Page 1 Operation (short) Switching off zones Page 2 FC120 Fire control panel (NL) Switching on zones Page 3 Procedure in case of Fault...
  • Page 6 Switching off detector zones (password required) The following example represents a possible operation sequence: WARNING System parts that have been switched off make it impossible to acquire and process alarms or faults! Fire may spread unhindered. Deploy staff to monitor the deactivated area. You must switch deactivated parts of the 'Site' back on as soon as possible.
  • Page 7 Switching on detector zones (Password required) When there is no event with a higher priority, isolations (switched off) are directly indicated on the display. You may then directly proceed with Step 3 below. Step Result Menu Press the button to open the main menu. Event summary (Password required) Enable / disable...
  • Page 8 Procedure in case of Fault Step Result Buzzer on the panel is switched off. is switched off. Press on the PMI. Read message/fault location on the display splay. Information on type and place of the fault. Information on type and place of the fault. Go to the fault location and remedy the cause of Go to the fault location and remedy the cause of When the fault has been eliminated,...