Festo DGCI Series Operating Instructions Manual

Festo DGCI Series Operating Instructions Manual

Linear drive with measuring system
Hide thumbs Also See for DGCI Series:
Table of Contents
  • Deutsch

    • Table of Contents
    • Bedienteile und Anschlüsse
    • Funktion und Anwendung
    • Transport und Lagerung
    • Voraussetzungen für den Produkteinsatz
    • Einbau
      • Einbau, Mechanisch
      • Einbau, Pneumatisch
      • Einbau, Elektrisch
    • Inbetriebnahme
      • Inbetriebnahme Gesamtanlage
      • Inbetriebnahme DGCI
    • Bedienung und Betrieb
    • Wartung und Pflege
    • Reparatur
    • Zubehör
    • Störungsbeseitigung
    • Technische Daten
  • Español

    • Conexiones y Elementos Operativos
    • Función y Aplicación
    • Transporte y Almacenamiento
    • Requisitos Previos para Poder Utilizar el Producto
    • Montaje
      • Instalación Mecánica
      • Instalación Neumática
      • Montaje de Los Componentes Eléctricos
    • Puesta a Punto
      • Puesta a Punto de todo el Sistema
      • Puesta a Punto del DGCI
    • Manejo y Funcionamiento
    • Cuidados y Mantenimiento
    • Accesorios
    • Reparación
    • Solución de Averías
    • Especificaciones Técnicas
  • Français

    • Organes de Commande Et Raccordements
    • Fonctionnement Et Application
    • Transport Et Stockage
    • Conditions de Mise en Œuvre du Produit
    • Montage
      • Montage Mécanique
      • Montage Pneumatique
      • Montage Électrique
    • Mise en Service
      • Mise en Service de L'installation Complète
      • Mise en Service du DGCI
    • Conditions D'utilisation
    • Maintenance Et Entretien
    • 11 Dépannage
    • Accessoires
    • Réparation
    • Caractéristiques Techniques
  • Italiano

    • Elementi Operativi E Attacchi
    • Funzionamento E Applicazione
    • Trasporto E Stoccaggio
    • Presupposti Per L'impiego del Prodotto
    • Montaggio
      • Montaggio Delle Parti Meccaniche
      • Montaggio Delle Parti Pneumatiche
      • Montaggio Delle Parti Elettriche
    • Messa in Funzione
      • Messa in Servizio Dell'impianto Completo
      • Messa in Funzione del DGCI
    • Uso E Funzionamento
    • Manutenzione
    • Accessori
    • Eliminazione Anomalie
    • Riparazione
    • Dati Tecnici

Advertisement

Available languages
  • EN

Available languages

  • ENGLISH, page 25

Quick Links

Linearantrieb mit Wegmess-
system
Linear drive with measuring
system
DGCI
(de) Bedienungs-
anleitung
(en) Operating
instructions
(es) Instrucciones
de utilización
(fr) Notice
d'utilisation
(it) Istruzioni
per l'uso
(zh)
8005076
1207b

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DGCI Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Festo DGCI Series

  • Page 1 Linearantrieb mit Wegmess- system Linear drive with measuring system DGCI (de) Bedienungs- anleitung (en) Operating instructions (es) Instrucciones de utilización (fr) Notice d’utilisation (it) Istruzioni per l’uso (zh) 8005076 1207b...
  • Page 2 ........... Festo DGCI-…-Z6 1207b...
  • Page 3: Table Of Contents

    ..........Festo DGCI-…-Z6 1207b Deutsch...
  • Page 4: Bedienteile Und Anschlüsse

    Druckluftanschluss (Bewegung nach rechts) Messsystem-Anschluss Schmiernippel für Wälzlager Erdungslasche für Messsystem Schlitten LED-Anzeige (grün: Power, rot: Error) Messsystem Befestigungsgewinde für Nutzlast Messmagnet Zentrierbohrungen für Nutzlast Führungsschiene Anschlagbolzen Befestigungsgewinde für Antrieb Druckluftanschluss (Bewegung nach links) Fig. 1 Festo DGCI-…-Z6 1207b Deutsch...
  • Page 5: Funktion Und Anwendung

    Händen zu berühren. Sonst schädigen Sie die Fettschicht. Berücksichtigen Sie das Gewicht des DGCI. Je nach Ausführung wiegt der DGCI über 72 kg. Sorgen Sie für Lagerbedingungen wie folgt: – kurze Lagerzeiten, – kühle, trockene, schattige korrosionsbeständige Lagerorte, – frei von starken Magnetfeldern. Festo DGCI-…-Z6 1207b Deutsch...
  • Page 6: Voraussetzungen Für Den Produkteinsatz

    Verschlusselemente an Druckluftanschlüssen (Verschmutzungsgefahr). Die Verpackungen sind vorgesehen für eine Verwertung auf stofflicher Basis (Ausnahme: Ölpapier = Restmüll). Sorgen Sie für Druckluft mit ordnungsgemäßer Aufbereitung ( Technische Daten). Lesen Sie auch die Dokumentation zu Ihrem Controller (z. B. SPC200). Festo DGCI-…-Z6 1207b Deutsch...
  • Page 7: Einbau

    Sie in dieser Anleitung nicht dazu aufgefordert werden. Vermeiden Sie, dass das Bandsystem beschädigt oder stark verschmutzt wird. Beschädigungen führen zu Leckage und mindern die Leistungsfähigkeit des DGCI. Fig. 3 Achten Sie auf einen Einbau ohne Verspannungen und Biegungen. Fig. 4 Festo DGCI-…-Z6 1207b Deutsch...
  • Page 8 Die Anzahl unterscheidet sich von den Angaben zum Linearantrieb DGC. S Stellen Sie sicher, dass die Platten wie folgt ausgerichtet sind: – exakt fluchtend (z. B. mit einem Lineal). – gleichmäßig verteilt über die gesamte Antriebslänge. Festo DGCI-…-Z6 1207b Deutsch...
  • Page 9 Fig. 8 7. Stellen Sie sicher, dass sich die Profil- befestigungen außerhalb des Verfahr- bereichs des Schlittens 3 befinden (insbesondere bei seitlicher Befestigung). Schieben Sie den Schlitten 3 hierfür einmal über die gesamte Verfahrstrecke. Fig. 9 Festo DGCI-…-Z6 1207b Deutsch...
  • Page 10 Bei Nutzlasten mit eigener Führung: Justieren Sie die Führungen von Nutzlast und DGCI exakt parallel. Nur so vermeiden Sie Überlastungen am Schlitten (zul. Kräfte Technische Daten). Achten Sie auf eine spielfreie Ankopplung der Nutzlast an den DGCI (< 0,1 mm). Festo DGCI-…-Z6 1207b Deutsch...
  • Page 11: Einbau, Pneumatisch

    Schaltungen, mit denen das Herabfallen verzögert werden kann. Verschlauchen Sie die Druckluftanschlüsse: Verschlauchungsvarianten DGCI-... (ohne Merkmal) DGCI-...-QD DGCI-...-QR DGCI-...-Q B Blauer Lösering (Bewegung nach links zum Messsystemende) S Schwarzer Lösering (Bewegung nach rechts zum Messsystemanschluss) Verschluss-Stopfen A Alternativanschluss Fig. 13 Festo DGCI-…-Z6 1207b Deutsch...
  • Page 12: Einbau, Elektrisch

    Flachstecker nach DIN 46246-2 und eine flexible, isolierte Leitung erforderlich. – Leitungsquerschnitt min. 2,5 mm – Leitungslänge max. 10 m Fig. 15 Verkabeln Sie den Messsystem-Anschluss 8 mit dem Steuerungssystem. Hierzu darf nur das Originalkabel verwendet werden. Festo DGCI-…-Z6 1207b Deutsch...
  • Page 13: Inbetriebnahme

    Nur bei völligem Stillstand der Masse darf ein Greifen an den DGCI möglich sein. Hinweis Für die elektronische Regelung des DGCI gelten spezielle Inbetriebnahme- vorschriften. S Vollziehen Sie die Inbetriebnahme gemäß den Beschreibungen zu Ihrem Controller. Festo DGCI-…-Z6 1207b Deutsch...
  • Page 14 DADP in Verbindung mit den Anschlägen KYC. S Beachten Sie hierzu die folgenden Belastungsdiagramme. DGCI-...-KF-YSR ∅ 18 ∅ 25 ∅ 32 ∅ 40 ∅ 63 DGCI-...-KF-YSRW ∅ 18 ∅ 25 ∅ 32 ∅ 40 ∅ 63 Fig. 18 Festo DGCI-…-Z6 1207b Deutsch...
  • Page 15 Positionierverhalten. Die Hubreduzierung darf jedoch folgende Werte nicht unter- Fig. 20 schreiten. DGCI-... Hubreduzierung r [mm] Fig. 21 Beim Einsatz mit SPC11 (Soft Stop): Stellen Sie sicher, dass die Endanschläge stabil sind und sich nicht elastisch verformen. Festo DGCI-…-Z6 1207b Deutsch...
  • Page 16 Ein Betrieb mit falsch montierten Dämpfungselementen zerstört den DGCI. S Montieren Sie : – die Anschlagbolzen am DGCI ausschließlich mit Kontermutter (K) – die Stoßdämpfer am DGCI-...-KF-YSR(W) ausschließlich zusammen mit der Anschlaghülse (H) und der Kontermutter (K). Festo DGCI-…-Z6 1207b Deutsch...
  • Page 17: Bedienung Und Betrieb

    Prüfen Sie, ob der Nutzhub innerhalb der zulässigen Grenzen bleibt: Inbetriebnahme unter “Feineinstellung des Hubes”). Bei Änderungen von Nutzlast oder Dynamik: Prüfen Sie, ob andere Dämpfungselemente beim SPC200/CMAX erforderlich sind ( Inbetriebnahme DGCI oder Beschreibungen zu Ihrem Controller). Festo DGCI-…-Z6 1207b Deutsch...
  • Page 18: Wartung Und Pflege

    S Schieben Sie den Schlitten während des Fettens hin und her. Sonst füllen sich die Fetträume nicht gleichmäßig. Alternativ bietet Ihnen Festo eine Inspektion als Serviceleistung inkl. des Nach- fettens an. Ansonsten ist der DGCI wartungsfrei. Festo DGCI-…-Z6 1207b Deutsch...
  • Page 19: Reparatur

    S Wählen Sie bitte das entsprechende Zubehör aus unserem Katalog www.festo.com/catalogue Störungsbeseitigung LED-Anzeige am Wegmesssystem Zustands-LED Fehler-LED Bedeutung (Power: grün) (Error: rot) Keine Spannung Initialisierungsfehler Normalfunktion Magnet nicht erkannt oder falsche Magnetanzahl Blinkt Blinkt Betriebsspannung nicht im angegebenen Bereich Fig. 28 Festo DGCI-…-Z6 1207b Deutsch...
  • Page 20 Siehe Hinweise zur Störungsbeseitigung in der Dokumentation zu Ihrem Controller. Starke Leckage Linearantrieb verspannt eingebaut Linearantrieb auf ebenem Untergrund befestigen. Dichtung verschlissen Zur Reparatur an Festo schicken. Linearantrieb Fehlendes Luftvolumen Anschlussquerschnitte vergrößern; erreicht nicht die Volumen vorschalten gewünschte Hohe Reibung oder Gegenkraft Größeren Antrieb wählen...
  • Page 21: Technische Daten

    – Zylinderprofil, Mitnehmer, Aluminium, eloxiert/lackiert Abschlussdeckel – Dichtungen, Dichtband Nitrilkautschuk / Polyurethan – Führungsband, Umlenkung, Polyacetal Schmutzabstreifer – Führungsschiene Stahl (Wälzführung) – Abdeckung Polyacetal, Polyamid, Aluminium – Wegmesssystem Aluminium, eloxiert; Polyphthalamide, glasfaserverstärkt – Kabel Polyurethan Fig. 30 Festo DGCI-…-Z6 1207b Deutsch...
  • Page 22 Nutzlastkomponente senkrecht zur Antriebsachse und statische Schlittenkippmomente: abhängig von Linearantriebstyp und Belastungsfall; rechnerisch zu ermitteln über Katalogangaben Formel für kombinierte Belastungen (Belastungs-Vergleichsfaktor): | My | | Fy | | Mx | | Mz | | Fz | Fig. 31 Festo DGCI-…-Z6 1207b Deutsch...
  • Page 23 Übertragungsrate [Mbit/s] ±0,02 % F.S. (min. ±50 ìm) Linearität Auflösung [mm] 0,005 Versorgungsspannung [V DC] 24 (±25 %) Stromaufnahme [mA] 100 typ. Temperaturkoeffizient < 15 ppm / °C CE-Zeichen (siehe Konformitätserklärung) nach EU-EMV-Richtlinie www.festo.com Fig. 32 Festo DGCI-…-Z6 1207b Deutsch...
  • Page 24 DGCI-… Festo DGCI-…-Z6 1207b Deutsch...
  • Page 25 ........Festo DGCI-…-Z6 1207b English...
  • Page 26: Operating Elements And Connections

    LED display (green: Power; red: Error) Slide Measuring system Fastening thread for work load Measuring magnet Centring holes for work load Guide rail Stop bolt Fastening thread for drive Compressed air connection (movement to the left) Fig. 1 Festo DGCI-…-Z6 1207b English...
  • Page 27: Function And Application

    Take the weight of the DGCI into consideration. Depending on the design, the DGCI can weigh over 72 kg. Ensure storage conditions as follows: – short storage periods – cool, dry, shaded storage locations protected from corrosion. – no influence from magnetic fields Festo DGCI-…-Z6 1207b English...
  • Page 28: Conditions Of Use

    The packing is intended for recycling (except for: oiled paper = other waste). Make sure there is a supply of correctly prepared compressed air Technical Specifications). Read also the documentation for your control system (e.g. SPC200). Festo DGCI-…-Z6 1207b English...
  • Page 29: Fitting

    Damage to the band system can cause leakage and reduce the efficiency of the DGCI. Fig. 3 Make sure that the device is fitted free of mechanical stress and distortion. Fig. 4 Festo DGCI-…-Z6 1207b English...
  • Page 30 The number differs from that specified for the linear drive DGC. S Make sure that the plates are arranged as follows: – exactly flush (e.g. with a ruler). – equally distributed over the complete drive length. Festo DGCI-…-Z6 1207b English...
  • Page 31 7. Make sure that the profile fastenings lie outside the positioning range of the slide 3 (especially with side fastening). In order to do this, push the slide 3 once over the complete positioning path. Fig. 9 Festo DGCI-…-Z6 1207b English...
  • Page 32 Adjust the guides of the work load and of the DGCI so that they are exactly parallel. Only in this way can you avoid overloading on the slide (permitted forces Technical Specifications). Make sure that the work load is coupled free of play to the DGCI (< 0.1 mm). Festo DGCI-…-Z6 1207b English...
  • Page 33: Fitting Pneumatic Components

    DGCI-...-QD DGCI-...-QR DGCI-...-Q B Blue release ring (movement to the left towards the measuring system end) S Black release ring (movem. to the right towards the measuring system connection) K Plug A Alternative connection Fig. 13 Festo DGCI-…-Z6 1207b English...
  • Page 34: Fitting The Electric Components

    – Cable cross-sectional area min. 2.5 mm – Cable length max. 10 m. Wire the measuring system connection 8 Fig. 15 with the control system. Only the original cable may be used for this purpose. Festo DGCI-…-Z6 1207b English...
  • Page 35: Commissioning

    It should not be possible to touch the DGCI until the mass has come to a complete stand. Note Special commissioning regulations apply to the electronic control of the DGCI. S Complete the commissioning as described in the manuals for the controller. Festo DGCI-…-Z6 1207b English...
  • Page 36 KYC. S Please note here the following loading diagrams. DGCI-...-KF-YSR ∅ 18 ∅ 25 ∅ 32 ∅ 40 ∅ 63 DGCI-...-KF-YSRW ∅ 18 ∅ 25 ∅ 32 ∅ 40 ∅ 63 Fig. 18 Festo DGCI-…-Z6 1207b English...
  • Page 37 Fig. 20 ing values. DGCI-... Stroke reduction r [mm] Fig. 21 When used with SPC11 (Soft Stop) Make sure that the end stops are stable and cannot deform elastically. Festo DGCI-…-Z6 1207b English...
  • Page 38 S Fit the following: – the stop bolts on the DGCI only with locking nut (K) – the shock absorbers on the DGCI-...-KF-YSR(W) only together with the stop sleeve (H) and the locking nut (K). Festo DGCI-…-Z6 1207b English...
  • Page 39: Operation

    Commissioning under “Accurate adjustment of the stroke”). If the work load or dynamics are modified: check whether other cushioning elements are required on the SPC200/CMAX Commissioning the DGCI or Manuals for the controller). Festo DGCI-…-Z6 1207b English...
  • Page 40: Care And Maintenance

    ELKALUB VP 874 (from Chemie-Technik) S Push the slide backwards and forwards during lubrication. Otherwise the grease cavities will not be filled evenly. Alternatively, Festo offers a service inspection which includes lubrication. Otherwise the DGCI does not require any maintenance. Festo DGCI-…-Z6 1207b English...
  • Page 41: Repairs

    LED display on measuring system Status LED Fault LED Meaning (Power: green) (Error: red) No voltage Initialization fault Normal function Magnet not recognized or incorrect number of magnets Flashes Flashes Operating voltage not within permissible range Fig. 28 Festo DGCI-…-Z6 1207b English...
  • Page 42 See instructions on eliminating faults in the documentation for your controller. Heavy leakage Linear drive fitted distorted Fasten the cylinder to a flat base. Seal worn Return to Festo for repairs. Linear drive does Air volume not sufficient Increase cross-section size of con- not achieve the nections;...
  • Page 43: Technical Specifications

    Nitrile rubber / polyurethane – guide band, reversing roller, Polyacetate dirt wiper: – guide rail: Steel (bearing guide) – cover: Polyacetate, polyamide, aluminium – measuring system: Aluminium, anodised: polyphthalamide, glass-fibre reinforced – cable: Polyurethane Fig. 30 Festo DGCI-…-Z6 1207b English...
  • Page 44 Formula for combined loadings (Load comparison factor): | My | | Fy | | Mx | | Mz | | Fz | Fig. 31 Festo DGCI-…-Z6 1207b English...
  • Page 45 Resolution [mm] 0.005 Supply voltage [V DC] 24 (±25 %) Current consumption [mA] 100 typical Temperature coefficient < 15 ppm / °C CE symbol (see conformity in accordance with EU EMC directive declaration) www.festo.com Fig. 32 Festo DGCI-…-Z6 1207b English...
  • Page 46 DGCI-… Festo DGCI-…-Z6 1207b English...
  • Page 47 ........Festo DGCI-…-Z6 1207b Español...
  • Page 48: Conexiones Y Elementos Operativos

    Rosca de fijación para la carga Imán de medición Agujeros de centrado para la carga Raíl de guía Perno de tope Rosca de fijación para actuador Conexión de aire comprimido (movimiento hacia la izquierda) Fig. 1 Festo DGCI-…-Z6 1207b Español...
  • Page 49: Función Y Aplicación

    Según la ejecución, el DGCI puede pesar más de 72 kg. Asegure unas condiciones de almacenamiento como sigue: – cortos períodos de almacenamiento – lugares fríos, secos, sombríos y resistentes a la corrosión, – fuera de la influencia de campos magnéticos. Festo DGCI-…-Z6 1207b Español...
  • Page 50: Requisitos Previos Para Poder Utilizar El Producto

    El embalaje está previsto para ser reciclado, (excepción: papel aceitado = desechos residuales). Asegúrese de que hay una alimentación de aire comprimido correctamente preparado ( “Especificaciones Técnicas”). Lea también la documentación de su controlador (p. ej. SPC200). Festo DGCI-…-Z6 1207b Español...
  • Page 51: Montaje

    Los daños pueden ocasionar fugas y reducen el rendimiento del DGCI. Fig. 3 Asegúrese de que el dispositivo se monta libre de esfuerzos mecánicos y de distorsión. Fig. 4 Festo DGCI-…-Z6 1207b Español...
  • Page 52 Fig. 5. La cantidad difiere de las especificaciones del actuador lineal DGC. S Asegúrese de que las placas están dispuestas de la siguiente manera: – con alineación exacta (p. ej. con una regla), – distribuidas de forma equidistante en toda la longitud del actuador. Festo DGCI-…-Z6 1207b Español...
  • Page 53 7. Asegúrese de que las fijaciones de perfil se hallen fuera del margen de desplazamiento del carro 3 (espe- cialmente las fijaciones laterales). Para ello empuje el carro 3 una vez por todo el recorrido de posicionado. Fig. 9 Festo DGCI-…-Z6 1207b Español...
  • Page 54 Ajuste las guías de la carga y del DGCI de forma que queden exactamente paralelas. Sólo de esta forma puede evitar sobrecargas en el carro (fuerzas permitidas, “Especificaciones técnicas”). Asegúrese de que la carga se acopla al DGCI libre de juego (< 0,1 mm). Festo DGCI-…-Z6 1207b Español...
  • Page 55: Instalación Neumática

    B Anillo suelto azul (movimiento hacia la izquierda hacia el final del sistema de medición) S Anillo suelto negro (movimiento hacia la derecha hacia la conexión del sistema de medición) K Tapón de cierre A Conexión alternativa Fig. 13 Festo DGCI-…-Z6 1207b Español...
  • Page 56: Montaje De Los Componentes Eléctricos

    – Sección transversal del cable: mín. 2,5 mm – Longitud del cable: máx. 10 m. Fig. 15 Cablee la conexión del sistema de medi- ción 8 junto con el sistema de control. Para ello sólo debe utilizarse el cable original. Festo DGCI-…-Z6 1207b Español...
  • Page 57: Puesta A Punto

    No debería ser posible tocar el DGCI hasta que la masa esté completamente parada. Nota Para la regulación electrónica del DGCI se aplican condiciones especiales de puesta a punto. S Lleve a cabo la puesta a punto según las instrucciones de su controlador. Festo DGCI-…-Z6 1207b Español...
  • Page 58 KYC. S Por favor, observe al respecto los siguientes diagramas de carga. DGCI-...-KF-YSR ∅ 18 ∅ 25 ∅ 32 ∅ 40 ∅ 63 DGCI-...-KF-YSRW ∅ 18 ∅ 25 ∅ 32 ∅ 40 ∅ 63 Fig. 18 Festo DGCI-…-Z6 1207b Español...
  • Page 59 DGCI-... Reducción de la carrera r [mm] Fig. 21 Si se utiliza con SPC11 (Soft Stop): Asegúrese de que los topes finales sean estables y no se deformen elásticamente. Festo DGCI-…-Z6 1207b Español...
  • Page 60 El DGCI se dañará si se hace funcionar con elementos de amortiguación montados incorrectamente. S Monte: – los pernos de tope en el DGCI exclusivamente con contratuercas (K), – los amortiguadores en el DGCI-...-KF-YSR(W) exclusivamente con el casquillo de tope (H) y la contratuerca (K). Festo DGCI-…-Z6 1207b Español...
  • Page 61: Manejo Y Funcionamiento

    Puesta a punto en “Ajuste de precisión de la carrera”). Si se modifica la carga o la dinámica: verifique si son necesarios otros elementos de amortiguación para SPC200/CMAX ( Puesta a punto del DGCI o Manual de su controlador). Festo DGCI-…-Z6 1207b Español...
  • Page 62: Cuidados Y Mantenimiento

    S Desplace el carro hacia adelante y hacia atrás durante la lubricación. De lo contrario no se rellenarán uniformemente con grasa todas las cavidades. Alternativamente, Festo ofrece un servicio de inspección que incluye la lubrica- ción. Aparte de la lubricación, el DGCI no necesita mantenimiento alguno.
  • Page 63: Reparación

    LED de fallo Significado (Power: verde) (Error: rojo) No hay tensión Fallo en la inicialización Funcionamiento normal Imán no reconocido o cantidad incorrecta de imanes Parpadea Parpadea Tensión de funcionamiento fuera del margen indicado Fig. 28 Festo DGCI-…-Z6 1207b Español...
  • Page 64 Fuga intensa Actuador lineal montado forzado Fijar el actuador lineal sobre una base plana. Juntas desgastadas Devolverlo a Festo para reparar. El actuador lineal Caudal de aire insuficiente Aumentar el diámetro de las cone- no alcanza la xiones, instalar un depósito previo velocidad deseada Alta fricción o contrafuerza...
  • Page 65: Especificaciones Técnicas

    – Banda de guía, rodillo inversor, Poliacetal rascadora – Raíl de guía Acero (guía de cojinete) – Tapa Poliacetal, poliamida, aluminio – Sistema de medición del recorrido Aluminio anodizado; poliftalamida reforzada por fibras de vidrio – Cable Poliuretano Fig. 30 Festo DGCI-…-Z6 1207b Español...
  • Page 66 Fórmula para cargas combinadas (Factor de comparación de cargas): | My | | Fy | | Mx | | Mz | | Fz | Fig. 31 Festo DGCI-…-Z6 1207b Español...
  • Page 67 Tensión de alimentación [V CC] 24 (±25 %) Consumo de corriente [mA] 100 tip. Coeficiente de temperatura < 15 ppm / °C Símbolo CE (consultar declaración de según directiva UE de máquinas CEM conformidad) www.festo.com Fig. 32 Festo DGCI-…-Z6 1207b Español...
  • Page 68 DGCI-… Festo DGCI-…-Z6 1207b Español...
  • Page 69 ........Festo DGCI-…-Z6 1207b Français...
  • Page 70: Organes De Commande Et Raccordements

    Chariot Système de mesure Taraudage pour la charge utile Bobine de mesure Trous de centrage pour la charge utile Rail de guidage Vis de butée Taraudage pour l’entraînement Raccord d’alimentation (mouvement vers la gauche) Fig. 1 Festo DGCI-…-Z6 1207b Français...
  • Page 71: Fonctionnement Et Application

    Selon l’exécution, le DGCI peut peser plus de 72 kg. Respecter les conditions de stockage suivantes : – des temps de stockage courts, – des emplacements de stockage frais, secs, ombragés et protégés de la corrosion, – non-exposition à des champs magnétiques puissants. Festo DGCI-…-Z6 1207b Français...
  • Page 72: Conditions De Mise En Œuvre Du Produit

    Les emballages sont conçus de sorte que leurs matériaux puissent être recyclés (exception : papier huileux = déchet résiduel). Veiller au conditionnement correct de l’air comprimé ( Caractéristiques techniques). Lire également la documentation de votre contrôleur (p. ex. SPC200). Festo DGCI-…-Z6 1207b Français...
  • Page 73: Montage

    Eviter d’endommager ou d’encrasser fortement le système de bande. Un endommagement du produit génère des fuites et entrave l’efficacité du DGCI. Fig. 3 Lors du montage, veiller à éviter les déformations et les fléchissements. Fig. 4 Festo DGCI-…-Z6 1207b Français...
  • Page 74 Ce nombre est différent de celui indiqué dans la documentation concernant le vérin linéaire DGC. S S’assurer que les plaques sont disposées de la façon suivante : – parfaitement en ligne (p.ex. utiliser une règle). – parfaitement réparties sur toute la longueur du vérin. Festo DGCI-…-Z6 1207b Français...
  • Page 75 3 (en parti- culier en cas de fixation latérale). Pour cela, déplacer le chariot 3 une fois sur toute la trajectoire de déplacement. Fig. 9 Festo DGCI-…-Z6 1207b Français...
  • Page 76 DGCI. C’est le seul moyen d’éviter les surcharges sur le chariot (pour les forces admissibles, Caractéristiques techniques). Veiller à ce que le couplage de la charge utile au DGCI ne présente aucun jeu (< 0,1 mm). Festo DGCI-…-Z6 1207b Français...
  • Page 77: Montage Pneumatique

    B Bague de démontage bleue (déplacement vers la gauche à l’extrémité du système de mesure) S Bague de démontage noire (déplacement vers la droite au raccord du système de mesure) K Bouchons d’obturation Raccord alternatif Fig. 13 Festo DGCI-…-Z6 1207b Français...
  • Page 78: Montage Électrique

    – Section de la ligne min. 2,5 mm – Longueur de la ligne max. 10 m. Fig. 15 Câbler le connecteur du système de mesure 8 avec le système de commande. Seul le câble d’origine doit être utilisé. Festo DGCI-…-Z6 1207b Français...
  • Page 79: Mise En Service

    Le DGCI ne doit être accessible qu’à l’arrêt complet de la masse. Nota Pour la régulation électronique du DGCI, respecter les prescriptions de mise en service spécifiques : S Réaliser la mise en service conformément aux instructions concernant votre contrôleur. Festo DGCI-…-Z6 1207b Français...
  • Page 80 DADP en association avec les butées KYC. S Tenir compte des diagrammes de charge suivants. DGCI-...-KF-YSR ∅ 18 ∅ 25 ∅ 32 ∅ 40 ∅ 63 DGCI-...-KF-YSRW ∅ 18 ∅ 25 ∅ 32 ∅ 40 ∅ 63 Fig. 18 Festo DGCI-…-Z6 1207b Français...
  • Page 81 Fig. 20 valeurs suivantes. DGCI-... Réduction de course r [mm] Fig. 21 En cas d’utilisation avec SPC11 (arrêt en douceur) : S’assurer que les butées de fin de course sont stables et ne sont pas déformées élastiquement. Festo DGCI-…-Z6 1207b Français...
  • Page 82 DGCI. S Monter : – la vis de butée sur le DGCI exclusivement avec un contre-écrou (K) – l’amortisseur sur le DGCI-...-KF-YSR(W) exclusivement avec la douille de butée (H) et le contre-écrou (K). Festo DGCI-…-Z6 1207b Français...
  • Page 83: Conditions D'utilisation

    Mise en service, “Réglage fin de la course”). En cas de modification de la charge utile ou de la dynamique : Vérifier si d’autres éléments d’amortissement sont nécessaires avec le SPC200/CMAX ( Mise en service du DGCI ou Notice de votre contrôleur). Festo DGCI-…-Z6 1207b Français...
  • Page 84: Maintenance Et Entretien

    S Décrire des mouvements de va-et-vient avec le chariot pendant le graissage. Sinon, les volumes de graissage ne seront pas remplis de manière uniforme. Festo vous propose également un contrôle dans le cadre du service après-vente comprenant le graissage ultérieur. Pour le reste, le DGCI est exempt d’entretien.
  • Page 85: Réparation

    Les réglages de précision et les contrôles nécessaires feront ainsi l’objet d’une attention particulière. Vous trouverez des informations relatives aux pièces détachées et aux pro- duits auxiliaires à l’adresse : www.festo.com/spareparts Pour le remplacement des éléments d’amortissement : Respecter le paragraphe “Pour le réglage fin de la course” dans le chapitre Mise en service.
  • Page 86 Renvoyer l’appareil au service après-vente Festo Le vérin linéaire Débit d’air insuffisant Agrandir les sections des raccords, n’atteint pas la intercaler un volume en amont vitesse souhaitée Frottement ou force opposée Choisir un axe plus grand importants Fig. 29 Festo DGCI-…-Z6 1207b Français...
  • Page 87: Caractéristiques Techniques

    – Rail de guidage : Acier (guidage à recirculation de billes) – Cache : Polyacétal, polyamide, aluminium – Système de mesure de déplacement : Aluminium, anodisé ; polyphtalamide, renforcé à la fibre de verre – Câble : Polyuréthane Fig. 30 Festo DGCI-…-Z6 1207b Français...
  • Page 88 ; calculs à effectuer à partir des données du catalogue Formule pour charges combinées : (facteur de comparaison de charge) : | My | | Fy | | Mx | | Mz | | Fz | Fig. 31 Festo DGCI-…-Z6 1207b Français...
  • Page 89 Résolution [mm] 0,005 Tension d’alimentation [V CC] 24 (±25 %) Intensité absorbée [mA] 100 typ. Coefficient de température < 15 ppm / °C Marque CE (voir Déclaration de selon la directive UE-CEM conformité) www.festo.fr Fig. 32 Festo DGCI-…-Z6 1207b Français...
  • Page 90 DGCI-… Festo DGCI-…-Z6 1207b Français...
  • Page 91 ..........Festo DGCI-…-Z6 1207b Italiano...
  • Page 92: Elementi Operativi E Attacchi

    Sistema di misurazione Filettatura di fissaggio per carico utile Magnete di misurazione Fori di centratura per carico utile Profilo di guida Perno d’arresto Filettatura di fissaggio per attuatore Attacco di alimentazione (movimento a sinistra) Fig. 1 Festo DGCI-…-Z6 1207b Italiano...
  • Page 93: Funzionamento E Applicazione

    A seconda della versione il DGCI pesa fin oltre 72 kg. Adottare misure appropriate allo scopo di garantire le seguenti condizioni di stoccaggio: – periodi di giacenza brevi, – locali freddi, asciutti, ombreggiati e resistenti alla corrosione, – esenti da forti campi magnetici. Festo DGCI-…-Z6 1207b Italiano...
  • Page 94: Presupposti Per L'impiego Del Prodotto

    Gli imballaggi possono essere riciclati in base al loro materiale (eccezione: carta oleata = rifiuti non riciclabili). Garantire una preparazione corretta dell’aria compressa ( Dati tecnici). Leggere anche la documentazione del vostro sistema di comando (ad es. SPC200). Festo DGCI-…-Z6 1207b Italiano...
  • Page 95: Montaggio

    Evitare danneggiamenti o sporco pesante al sistema di fasce di tenuta. I danneggiamenti causano il trafilamento e diminuiscono l’efficienza del DGCI. Fig. 3 Verificare che il cursore non sia soggetto a sollecitazioni meccaniche o flessioni. Fig. 4 Festo DGCI-…-Z6 1207b Italiano...
  • Page 96 Il numero si distingue dalle indicazioni per l’attuatore lineare DGC. S Accertarsi che le piastre siano allineate in modo seguente: – esattamente nella direzione di movimento (ad es. con una riga). – con distribuzione uniforme attraverso l’intera lunghezza dell’attuatore. Festo DGCI-…-Z6 1207b Italiano...
  • Page 97 20 Nm Fig. 8 7. Accertarsi che i fissaggi per profili non intralcino il movimento della slitta 3 (soprattutto nel caso di montaggio laterale). Spostare perciò la slitta 3 una sola volta lungo l’intera corsa. Fig. 9 Festo DGCI-…-Z6 1207b Italiano...
  • Page 98 Le guide del carico utile e il DGCI devono essere perfettamente paralleli. Soltanto in questo modo è possibile evitare un’eccessiva sollecitazione della slitta (le forze ammissibili sono riportate in Dati tecnici). Verificare un accoppiamento del carico utile senza gioco al DGCI (< 0,1 mm). Festo DGCI-…-Z6 1207b Italiano...
  • Page 99: Montaggio Delle Parti Pneumatiche

    B Anello di sbloccaggio blu (movimento a sinistra verso il termine del sistema di misurazione) S Anello di sbloccaggio nero (movimento a destra verso connettore per il sistema di misurazione) K Tappo di chiusura A Attacco alternativo Fig. 13 Festo DGCI-…-Z6 1207b Italiano...
  • Page 100: Montaggio Delle Parti Elettriche

    – Sezione di cavo min. 2,5 mm – Lunghezza di cavo max. 10 m. Fig. 15 Cablare il connettore del sistema di misu- razione 8 con il sistema di comando. Impiegare esclusivamente il cavo originale. Festo DGCI-…-Z6 1207b Italiano...
  • Page 101: Messa In Funzione

    è fermo. Nota La regolazione elettronica del DGCI è soggetta a particolari prescrizioni di messa in funzione. S Eseguire la messa in funzione osservando le istruzioni riportate nelle descrizioni del vostro controllore. Festo DGCI-…-Z6 1207b Italiano...
  • Page 102 KYC. S Considerare per ciò i seguenti diagrammi di carico. DGCI-...-KF-YSR ∅ 18 ∅ 25 ∅ 32 ∅ 40 ∅ 63 DGCI-...-KF-YSRW ∅ 18 ∅ 25 ∅ 32 ∅ 40 ∅ 63 Fig. 18 Festo DGCI-…-Z6 1207b Italiano...
  • Page 103 Fig. 20 DGCI-... Limitazione corsa r [mm] Fig. 21 Per un impiego con SPC11 (Soft Stop): Verificare che le battute di fine corsa siano stabili e che non subiscano una deformazione elastica. Festo DGCI-…-Z6 1207b Italiano...
  • Page 104 Il funzionamento con elementi di ammortizzazione montati erratamente può danneggiare il DGCI. S Montare: – i perni d’arresto al DGCI utilizzando esclusivamente il controdado (K) – gli ammortizzatori al DGCI-...-KF-YSR(W) solo insieme a bussola d’arresto (H) e controdado (K). Festo DGCI-…-Z6 1207b Italiano...
  • Page 105: Uso E Funzionamento

    Messa in funzione in “Regolazione di precisione della corsa”). In caso di variazione del carico utile o della dinamicità: Verificare se per l’SPC200/CMAX sono necessari altri elementi di ammortizza- zione ( Messa in funzione del DGCI o Descrizioni del vostro controllore). Festo DGCI-…-Z6 1207b Italiano...
  • Page 106: Manutenzione

    S Spostare la slitta avanti e indietro durante la lubrificazione. Altrimenti le cavità di lubrificazione non si riempino in modo uniforme. Festo offre in alternativa un’ispezione come prestazione del servizio di assistenza, che include anche la lubrificazione. Il DGCI non richiede altri interventi di manu- tenzione.
  • Page 107: Riparazione

    DGCI-… Riparazione Raccomandazione: : inviare il prodotto al servizio assistenza Festo Così vengono eseguite soprattutto le microtarature e verifiche necessarie. Per informazioni su parti di ricambio e mezzi ausiliari vedi: www.festo.com/spareparts Per sostituire gli elementi di ammortizzazione: Osservare il paragrafo “Regolazione di precisione della corsa” nel capitolo Messa in servizio.
  • Page 108 Forte perdita Attuatore lineare soggetto a sollecita- Fissare l’attuatore lineare su una zioni meccaniche superficie piana Guarnizione usurata Inviare il dispositivo alla Festo per la riparazione. Velocità dell’attua- Portata d’aria insufficiente Installare attacchi di sezione tore lineare minore maggiore, regolare la portata...
  • Page 109: Dati Tecnici

    Poliacetato raschiapolvere – Profilo di guida Acciaio (guida a ricircolo di sfere) – Placchetta di copertura Poliacetale, poliammide, alluminio – Trasduttore di posizione Alluminio anodizzato; poliftalamide rinforzato in fibra di vetro – Cavo Poliuretano Fig. 30 Festo DGCI-…-Z6 1207b Italiano...
  • Page 110 Catalogo Formula per carichi combinati (Fattore di confronto del carico): | My | | Fy | | Mx | | Mz | | Fz | Fig. 31 Festo DGCI-…-Z6 1207b Italiano...
  • Page 111 Tensione di alimentazione [V DC] 24 (±25 %) Corrente assorbita [mA] 100 type Coefficiente di temperatura < 15 ppm / °C Marchio CE (vedi Dichiarazione di secondo la direttiva UE sulla CEM conformità) www.festo.com Fig. 32 Festo DGCI-…-Z6 1207b Italiano...
  • Page 112 DGCI-… Festo DGCI-…-Z6 1207b Italiano...
  • Page 113 DGCI-… 中文 – 带位移测量系统的直线驱动器 DGCI 目录 Festo DGCI-…-Z6 1207b...
  • Page 114 DGCI-… 操作部件和接口 Festo DGCI-…-Z6 1207b...
  • Page 115 DGCI-… 功能和应用 – – – – 运输和存放 • • • – – – Festo DGCI-…-Z6 1207b...
  • Page 116 DGCI-… 产品使用的前提条件 • • • 才 • • • • • • Festo DGCI-…-Z6 1207b...
  • Page 117 DGCI-… 安装 • • • • • Festo DGCI-…-Z6 1207b...
  • Page 118 DGCI-… • – – 100 … 400 401 … 600 601 … 1200 1201 … 1400 1401 … 2000 • • – – Festo DGCI-…-Z6 1207b...
  • Page 119 DGCI-… HPC-... 32/40 MUC-... 25/32 Festo DGCI-…-Z6 1207b...
  • Page 120 DGCI-… • • • – – – • 才 • < Festo DGCI-…-Z6 1207b...
  • Page 121 DGCI-… • • DGCI-...(无标记) DGCI-...-QD DGCI-...-QR DGCI-...-Q Festo DGCI-…-Z6 1207b...
  • Page 122 DGCI-… … … … > 才 • 5 ìm • – – • Festo DGCI-…-Z6 1207b...
  • Page 123 DGCI-… 调试 • • – – 才 • 描述 Festo DGCI-…-Z6 1207b...
  • Page 124 DGCI-… 冲 金属 挡 即 • 寸 够 冲 • 仅 液 冲 挡 • DGCI-...-KF-YSR ∅ ∅ ∅ ∅ ∅ DGCI-...-KF-YSRW ∅ ∅ ∅ ∅ ∅ Festo DGCI-…-Z6 1207b...
  • Page 125 DGCI-… 依 心 – – … 液 冲 • 检查 • 书 • 检查 选择 挡 – – 顺序 – 碍 – 高 • 每 减 留 每 留 减 列 • 挡 稳 且 弹 变 Festo DGCI-…-Z6 1207b...
  • Page 126 功 靠 稳 列 DGCI-... … … … … … DGCI-…-YSR(W) … … … … … DGCI-...-GP … … … … – 冲 毁 • – 仅 母 K – 仅 挡 母 液 冲 ... K Festo DGCI-…-Z6 1207b...
  • Page 127 DGCI-… 再 挡销 冲 母 操作和运行 • – – 才 了 • 检查 “ 节” 了 • 检查 他 冲 Festo DGCI-…-Z6 1207b...
  • Page 128 年 • 列 隔 多尘 清洁 – – < > – > ° – > 孔 承加 针 嘴 枪 选 针 射 he e echn • 加 另 选择 案 esto 客户 括加 检 非 维 Festo DGCI-…-Z6 1207b...
  • Page 129 DGCI-… 修理 • 寄 们 检查 • 辅助 www festo co /spareparts 更换 冲 • 节 “ 节 ” 附件 • 们 目录选择 附 www festo co /catalo ue Festo DGCI-…-Z6 1207b...
  • Page 130 DGCI-… 故障排除 Festo DGCI-…-Z6 1207b...
  • Page 131 DGCI-… 技术参数 塞 塞 ì … … Á Á ¼ Å … – – – – – – – Festo DGCI-…-Z6 1207b...
  • Page 132 DGCI-… 负载组合公式 (负载比系数): | My | | Fy | | Mx | | Mz | | Fz | Festo DGCI-…-Z6 1207b...
  • Page 133 DGCI-… ì ± ± ± < Festo DGCI-…-Z6 1207b...
  • Page 134 Copyright: communication de son contenu sont interdites, sauf Festo AG & Co. KG, autorisation écrite expresse. Tout manquement à cette règle Postfach est illicite et expose son auteur au versement de dommages D-73726 Esslingen et intérêts.

Table of Contents