Related Manuals for Eaton xComfort Room Controller Touch
Summary of Contents for Eaton xComfort Room Controller Touch
- Page 1 Room Controller Touch Effect Regulation User manual (For software version 1.36 or higher) xComfort Room Controller Touch – Effect Regulation - User manual 2v00_EN...
- Page 2 QR kód. Voor andere talen en meer informatie over xComfort ga naar www.eaton.nl/xcomfort of www.xcomfort.nl of maak gebruik van de QR-code xComfort Room Controller Touch – Effect Regulation - User manual 2v00_EN ii | P a g e...
-
Page 3: Table Of Contents
3.4.2 (Optional) Edit the week program timer ..................12 3.4.3 (Optional) Edit/set the current time and date ................15 3.4.4 (Optional) Edit/set the monthly clock correction factor ............16 xComfort Room Controller Touch – Effect Regulation - User manual 2v00_EN iii | P a g e... -
Page 4: Introduction
These operating instructions are intended for end users and describe the operation and menu structure of the Room Controller Touch with software version 1v36 or higher. xComfort Room Controller Touch – Effect Regulation - User manual 2v00_EN P a g e... - Page 5 Please contact a suitably qualified electrical engineer for assembly, installation and basic configuration of the device, as well as for its disposal. Faulty installation or configuration may pose a danger to property and persons. xComfort Room Controller Touch – Effect Regulation - User manual 2v00_EN P a g e...
-
Page 6: Room Controller Touch
To prevent any unwanted changes, the display can be locked by pressing it at the top for approximately 5 seconds until ‘Loc.’ (flashing) appears on the display. xComfort Room Controller Touch – Effect Regulation - User manual 2v00_EN P a g e... -
Page 7: Cleaning Mode
In cleaning mode, the Room Controller Touch will ignore any touching activity on the display. The display will then show the remaining time in seconds until the Room Controller Touch switches back to normal operation. >7 Sec. xComfort Room Controller Touch – Effect Regulation - User manual 2v00_EN P a g e... -
Page 8: Replacing The Batteries
Never recharge standard batteries!! This entails a risk of explosion. Do not throw the batteries into fires. Do not short-circuit the batteries. xComfort Room Controller Touch – Effect Regulation - User manual 2v00_EN P a g e... -
Page 9: Operation Mode
Edit the pre-defined regulation percentage values (Optional) Edit the week program (Optional) Edit the time and date (Optional) Edit the clock correction factor xComfort Room Controller Touch – Effect Regulation - User manual 2v00_EN P a g e... -
Page 10: Basic Functions
(operation modes). It is possible to manually switch between these pre-defined regulation values. The pre-defined regulation values can xComfort Room Controller Touch – Effect Regulation - User manual 2v00_EN P a g e... -
Page 11: Optional) Show The Outdoor Temperature
3.2.6 (Optional) Show the floor temperature This function is available if, during installation, the external temperature sensor input is configured to be used as a floor temperature sensor. xComfort Room Controller Touch – Effect Regulation - User manual 2v00_EN P a g e... -
Page 12: Show The Time And The Day Of The Week
2-pole pushbutton. The touch button on the left controls the ON/UP (short/long press) function while the one on the right handles the OFF/DOWN function. xComfort Room Controller Touch – Effect Regulation - User manual 2v00_EN P a g e... -
Page 13: Enhanced Functions
If the week program is activated (ON), the device will switch to the correct operation mode in accordance with the week program for the current time. Optional Step 1 Step 2 Deactivated (OFF) Activated (ON) Step 3 Timeout xComfort Room Controller Touch – Effect Regulation - User manual 2v00_EN 10 | P a g e... -
Page 14: Edit Functions
Controller Touch uses these pre-defined regulation values for climate control. Optional Step 1 Enter edit mode Step 2 (Select edit) Edit icon is flashing xComfort Room Controller Touch – Effect Regulation - User manual 2v00_EN 11 | P a g e... -
Page 15: Optional) Edit The Week Program Timer
For each day of the week, the Room Controller Touch supports up to 6 manually (re-)programmable timeslots during which it will switch from one pre-defined regulation value (operation mode) to another. Optional xComfort Room Controller Touch – Effect Regulation - User manual 2v00_EN 12 | P a g e... - Page 16 The selected switch point is flashing Changing the pre-defined regulation value Change the pre- defined regulation value The selected pre-defined regulation value is underlined xComfort Room Controller Touch – Effect Regulation - User manual 2v00_EN 13 | P a g e...
- Page 17 Changing the time (hours) Change the time (hours) Step 1 (select) The hours are flashing Step 2 (change) Leave edit mode (Leave edit mode) Timeout or xComfort Room Controller Touch – Effect Regulation - User manual 2v00_EN 14 | P a g e...
-
Page 18: Optional) Edit/Set The Current Time And Date
Select the clock Enter edit mode Select item and change Select (1-6) is flashing Hours Minutes Day of the month Month Year xComfort Room Controller Touch – Effect Regulation - User manual 2v00_EN 15 | P a g e... -
Page 19: Optional) Edit/Set The Monthly Clock Correction Factor
This will then cause the week program to switch to the desired setpoint temperature either too early or too late. Select the clock Enter edit Press edit > 5 Sec Change Leave edit xComfort Room Controller Touch – Effect Regulation - User manual 2v00_EN 16 | P a g e... - Page 20 © Eaton Industries (Austria) Eugenia 1 3943 Schrems Austria www.xcomfort.com www.eaton.eu/xcomfort xComfort Room Controller Touch – Effect Regulation - User manual 2v00_EN 17 | P a g e...
Need help?
Do you have a question about the xComfort Room Controller Touch and is the answer not in the manual?
Questions and answers