1. Manuals
  2. Brands
  3. Selkirk Manuals
  4. Indoor Fireplace
  5. FC
  6. Installation instructions, warranty and maintenance manual

Selkirk FC Installation Instructions, Warranty And Maintenance Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

RM19957-2
10/09
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FC and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Selkirk FC

Summary of Contents for Selkirk FC

  • Page 1 RM19957-2 10/09...
  • Page 2 INSTALLATION INSTRUCTIONS & MAINTENANCE GUIDE MODEL FC FACTORY BUILT INSULATED CHIMNEY LISTED ® CAN/ULC-S604, CAN/ULC-S610 A MAJOR CAUSE OF CHIMNEY-RELATED FIRES IS FAILURE TO MAINTAIN REQUIRED CLEARANCES (AIR SPACES) TO COMBUSTIBLE MATERIALS. IT IS OF THE UTMOST IMPORTANCE THAT THIS CHIMNEY BE INSTALLED ONLY IN ACCORDANCE WITH THESE INSTRUCTIONS.

  • Page 3: Table Of Contents

    TABLE OF CONTENTS TYPES OF APPLIANCE PRE INSTALLATION GUIDELINES TOOLS FRAMING DETAILS 4 - 5 CEILING SUPPORT INSTALLATION STOVE PIPE INSTALLATION 5 - 6 ATTIC INSULATION SHIELD INSTALLATION FIRESTOP RADIATION SHIELD INSTALLATION ELBOW INSTALLATION WALL SUPPORT INSTALLATION 7 - 8 CATHEDRAL CEILING SUPPORT INSTALLATION 8 - 9 ROOF SUPPORT INSTALLATION...

  • Page 4: Types Of Appliance

    FIGURE 1 2 ft. (600mm) 3 ft. (900mm) Your SuperVent/SuperPro Model FC chimney is intended as a min. component for specific listed factory built fireplaces and for connection to liquid fuel or gas fired residential type appliances and 2 ft.

  • Page 5: Ceiling Support Installation

    In some application, the is enclosed immediately below the roof. crimped end will need to be removed as per fuel requirements and - Suitable lengths of Chimney (Model FC). The chimney diameter local installation codes. should be sized to suit the appliance.

  • Page 6: Attic Insulation Shield Installation

    Selkirk's Model DSP which can be installed at reduced clearances of The telescoping portion of the AIS will eliminate the need to trim the 6"...

  • Page 7: Elbow Installation

    Lock- ing bands must be used at all chimney joints. - Suitable lengths of chimney (Model FC). The chimney diameter should be sized to suit the appliance. Never install an elbow in a joist area. Chimney sections must pass vertically through framed joist areas.
  • Page 8 - Cathedral Ceiling Support: JSC CCS. Support Plate - Roof Flashing Assembly: JSC AAF, JSC AF2 - required when the chimney penetrates a roof. - Suitable lengths of chimney ( Model FC). The chimney diameter Female Coupler (Down) should be sized to suit the appliance.

  • Page 9: Cathedral Ceiling Support Installation

    The bottom chimney length(s) should protrude into the living space Slide the Roof Support down over the chimney section until its so that proper clearances are maintained on the stove pipe connec- brackets rest on the roof or floor. Tighten the collar around the tor.

  • Page 10: Roof Flashing Installation

    Raincap 12" Ruler Level Ventilation Slots Roof 3" Storm Collar Pitch is 3/12 Flashing Rafter Radiation FIGURE 14 Roof Pitch Calculation Shield Enclosure Slide a Roof Flashing Assembly suitable to your roof slope over the FIGURE 16 Storm Collar/Flashing Installation chimney.

  • Page 11: Maintenance And Cleaning Of Chimney

    Rubber Boot Flashing Kit URBFK1 URBFK1 CHEMICALLY TREATED WOOD, ETC.. Storm Collar JSC*SC JSC*SC Universal Shielding Insulation JUSI JUSI * Specify chimney size Model SuperVent(FC) and SuperPro (SPR) chimneys and components are interchangeable with one another. Both are listed to CAN/ULC-S604 and CAN/ULC-S610.

  • Page 12: Chart 1 - Offset Tables

    CHART 1 - OFFSET CHIMNEY INSTALLATION It may be necessary to offset the chimney in order to clear a joist or an obstacle. The three (3) charts below will assist you in selecting the proper combination of elbow angle and chimney length(s) that will provide the necessary degree of offset within an available height. OFFSET CHART 1.

  • Page 13: Chart 2 - Chimney Height Above Roof

    CHART 3 - Connector Pipe Clearance below Cathedral Support 1. Identify the type of connector pipe you will be installing, single wall (requires 18" clearance to combustibles) or Selkirk's Double Wall Stove Pipe (model DSP) which requires 6" clearance to combustibles.

  • Page 14: Installation Record & Product Registration

    TECHNICIAN NAME:______________________________________ Address:________________________________________________ City: ___________________________________________________ Province:__________________________________________________ PRODUCT REGISTRATION Please register your Chimney with the Manufacturer. Mail to: Selkirk Corporation, Product Registration, P.O. Box 526, Depot 1, Hamilton, On, L8L 7X6 Register Online @: www.selkirkcorp.com Name: ____________________________________________________________________________________ Address:_________________________________________________________________________________ City:______________________________________________________________________________________ State:________________________________________ Postal Code:___________Telephone #:__________...

Table of Contents