SMC Networks IR1000 Series Operation Manual
Precision reguretor
Hide thumbs
Also See for IR1000 Series:
- Operation manual (16 pages) ,
- Operation manual (16 pages) ,
- Operation manual (16 pages)
Subscribe to Our Youtube Channel
Related Manuals for SMC Networks IR1000 Series
Summary of Contents for SMC Networks IR1000 Series
- Page 1 No.IR10-OM00006 PRECISION REGURETOR PRODUCT NAME IR1000-F01-DII00467・IR1010-F01-DII00467 MODEL/ Series...
-
Page 2: Table Of Contents
Table of Contents Safety 2～3 １．Specifications ２．Operation principle ３．How to order ４．Production lot number symbol ５．Caution on handling 7～8 ６．Troubleshooting ７．Spare parts list ８．Assembling drawing ９．Drawing... - Page 3 Safety Be sure to read this operation manual before handling, and understand the contents to operate the product properly. Keep this operation manual carefully to be able to refer to it whenever it is required, and ensure to give it to an end user. These safety instructions are intended to prevent hazardous situation and/or equipment damage.
- Page 4 Warning 1. The compatibility of pneumatic equipment is the responsibility of the person who designs the pneumatic system or decides its specifications. Since the products specified here are used in various operating conditions, their compatibility for the specific pneumatic system must be based on specifications provided by a person in c harge of design and specification after analyzing and/or testing to meet your specific requireme nts.
-
Page 5: １．Specifications
Introduction Series IR1000 precision type regulator is superior in relief characteristics and constant pressure is kept in the case of flowing backward. IR10∗0-F01-DII00467 is designated special for Sensatronic to be applied for respirator. 1. Specification Model IR1000-F01-DII00467 IR1010-F01-DII00467 Max. 1.0 Max. -
Page 6: ２．Operation Principle
2. Structure and operating principles When the Adjusting screw①is turned, the nozzle③ is closed by the diaphragm disk②, allowing the supply air that flows in from the upstream side to pass through the fixed orifice④ and to acts on diaphragm C⑥ as nozzle back pressure, the main valve⑦ is pushed down by the generated force and the supply pressure flows out to the downstream side. -
Page 7: ３．How To Order
3. How to order I R 1 0 ※ 0 - Ｆ 0 1 – D I I 0 0 4 6 7 Special order Connecting port 01：1/8 Connect screw Ｆ：Ｇ Settting pressure 0：0.05～2bar 1：0.1～4bar 4. Production lot number symbol The production lot symbol is described to product name plate. - Page 8 5.Precautions Warning Handling (1) If the system is expected to be dangerous when the Precision regulator, please consider system with safety circuit to avoid danger. Warning Operating Environment (1) Do not operate in locations having an atmosphere of corrosive gases, chemicals, sea water, water or steam, or where there will be contact with the same.
- Page 9 Caution Operation (1) Do not use a precision regulator outside the range of its specifications as this can cause failure. (Refer to specifications.) (2) When mounting is performed, make connections while confirming port indications. (3) If a directional switching valve (solenoid valve, mechanical valve, etc. ) is mounted on the supply side of the regulator and repeatedly switched ON and OFF, wear of the nozzle/flapper section will be accelerated and a discrepancy in the setting value may occur.
-
Page 10: ６．Troubleshooting
６． Troubleshooting Caution For troubles in the table below, replacement by the component is recommended. Non-conformance occurred due to repalcement with spare part is not guaranteed. Phenomenon Checking item Causes Countermeasures Pressure is not Air is not exhausted from Fixed orifice Replace the component or output... -
Page 11: ７．Spare Parts List
Revision history URL http://www.smcworld.com Phone AUSTRIA / (43) 2262-62 280 ITALY / (39) 02-92711 BELGIUM / (32) 3-355 1464 NETHERLANDS / (31) 20-531 8888 CZECH REP. / (420) 5-414 24611 NORWAY / (47) 67 12 90 20 DENMARK / (45) 70 25 29 00 POLAND / (48) 22-548 50 85 FINLAND / (358) 9-859 580 PORTUGAL / (351) 2 610 89 22...
Need help?
Do you have a question about the IR1000 Series and is the answer not in the manual?
Questions and answers