Medium temperature. bulk produce and bakery merchandisers (34 pages)
Summary of Contents for Hussmann EcoVision EZ Door Upgrade
Page 1
® EcoVision EZ Door Upgrade for Impact Medium Temperature Merchandisers Installation & Operation Manual IMPORTANT P/N 0558756_C Keep in store for Impact Series future reference! May 2018 Spanish 3005584 French 3005586 MANUAL- I/O IMPACT ECOVISION EZ...
Page 2
PERSONAL PROTECTION EQUIPMENT (PPE) Personal Protection Equipment (PPE) is required whenever servicing this equipment. Always wear safety glasses, gloves, protective boots or shoes, long pants, and a long-sleeve shirt when handling glass. U.S. & Canada 1-800-922-1919 • Mexico 01-800-890-2900 • www.hussmann.com...
Phillips Screw Driver if cases are not properly loaded. Excessive ambient conditions may cause condensation and therefore sweating of doors. Facility operators should monitor doors and floor conditions to ensure safety of persons. U.S. & Canada 1-800-922-1919 • Mexico 01-800-890-2900 • www.hussmann.com...
Do not store items or Accidental glass breakage can be dangerous. flammable materials atop the unit. Always wear protective safety glasses and gloves when handling glass. HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
Shims are provided with each door kit. Use Flat Washer provided metal shims. Hex Nut Figure 2-2 — Loosen Canopy Screws Loosen Canopies of Multi-deck Wall Cases between cases U.S. & Canada 1-800-922-1919 • Mexico 01-800-890-2900 • www.hussmann.com...
Figure 4-2— Remove Front Rail The Case(s) are now ready to be outfitted with EcoVision EZ Doors. Refer to the door part identifications on the next page to become familiar with the standard case parts. HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
C. Install inner bottom rail support and attach it to the front supports using #8 x in. screws. Attach the outer bottom rail support to the front of the case with #8-18 x in. screws. HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
(Fig 6-2a) C. Make sure extrusion is level. Level D. Fasten #8 screws as shown in Fig 6-2a . Space approximately every 12 inches. No Gap U.S. & Canada 1-800-922-1919 • Mexico 01-800-890-2900 • www.hussmann.com...
Pre 04/ 1996 cases and Post 04/1996 Impact cases. The difference in the Canopy is shown below Impact Canopy 4/96 to Impact Canopy Pre 4/96 Current — No Retrofit No Retrofit Flange Direction Flange Direction HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
Retainer, Fig 8a-2 #8-18 x 3/8 Fascia Retainer Light Channel Retainer Canopy Support #8-32 x 1/2 Install screws as shown by arrows Install screws as shown by arrows U.S. & Canada 1-800-922-1919 • Mexico 01-800-890-2900 • www.hussmann.com...
Page 13
Extension to the top of the case as shown in Fig 8B-2 to fasten both pieces together. Gussets Narrow Width Canopy Assembly Light Channel Retainer Canopy Fascia Support Retainer (Narrow (Narrow Cases) Cases) #8-32 x 1/2 Install screws as shown by arrows HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
Insert the Tabs on the Canopy Channel Assembly into Light Channel Retainer as shown in Fig 10-1 and 10-2 and fasten with #8 screws as shown by arrow. Light Channel Retainer Canopy Channel Retainer U.S. & Canada 1-800-922-1919 • Mexico 01-800-890-2900 • www.hussmann.com...
It may not be necessary to perform this step for some lineups. See step 15 for more infor- mation. Removing ALL canopy nuts could cause case parts to become loose and fall, causing serious personal injury. HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
Angle the door retainer into the front side (outside the case) of bottom rail extrusion. Squeeze retainer until it snaps into bottom extrusion as shown in Fig. 15-1 and 15-2. Squeeze Retainer U.S. & Canada 1-800-922-1919 • Mexico 01-800-890-2900 • www.hussmann.com...
DO NOT USE (Case 2) (Case 1) DO NOT USE Lockwasher Bolt 1/4 -20 x 3/4 DO NOT USE Bolt Location Nut 1/4-20 Lockwasher Bolt 1/4 Figure 16-1 Gasket -20 x 3/4 1/2 x 1/4 HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
Arrow on hinge plate must face inside of case as shown. If the arrow is installed on the outside the doors will not close. Move plate in inch from end Bottom Rail Alignment Plate use on case joints U.S. & Canada 1-800-922-1919 • Mexico 01-800-890-2900 • www.hussmann.com...
Fig. 19-2. Figure 19-2 Do not carry doors by handle. Bottom of Gravity Hinge Personal injury and damage to “L” marked for LEFT the doors may result. door HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
To correct shift the bottom plate to the left! To correct shift the bottom plate to the right! To Correct Shift the Bottom Plate to the Right To Correct Shift the Bottom Plate to the Left STEP 1 U.S. & Canada 1-800-922-1919 • Mexico 01-800-890-2900 • www.hussmann.com...
Page 21
Check level with case filled with product. Do not put level on top of s h o w n case. O U T S I D E o f D o o r HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
Failure to reinstall canopy nuts could cause case parts to become loose and fall, causing serious personal injury. Deck Pans Bumper Figure 21-1 — Replace Canopy Fascia Figure 21-2 U.S. & Canada 1-800-922-1919 • Mexico 01-800-890-2900 • www.hussmann.com...
Directions for installing optional stability kits for narrow xcel cases Case Tipping may occur if cases are not properly leveled and secured, or if cases are not properly loaded. HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
B. For anchoring case to wall: Mount unistrut to the store wall supports, then connect the existing anti-tip brackets to unistrut. Supply brackets and wood screws and washers are used to mount unistrut to wall. U.S. & Canada 1-800-922-1919 • Mexico 01-800-890-2900 • www.hussmann.com...
LINE-UPS contact your Hussmann sales representative. A. Each line-up of cases has a solenoid valve or The Hussmann Team will help ensure that your Evaporator Pressure Regulator (EPR) by which existing equipment remains at optimal perfor- to control temperature.
35%, a resize is more than likely necessary. If this line is not resized when it is necessary to do so, lubricant return back to the compressors may be an issue. U.S. & Canada 1-800-922-1919 • Mexico 01-800-890-2900 • www.hussmann.com...
This is called “case credits.” This reduction in AC load is calculated based on the “spillover” of the chilled air from these cases by adding doors this “spillover” is eliminated. HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
Below is an exploded view of the end filler kit parts and the contour end panel. Figure 1-1 Figure 1-2 U.S. & Canada 1-800-922-1919 • Mexico 01-800-890-2900 • www.hussmann.com...
Page 29
C. Temporily attach exterior end filler panel with two #8 screws, insert foam cutout, repeat for interior end filler panel. The end filler panels will hold the insulation in place (as shown in Fig. 2-4). Figure 2-4 Figure 2-3 HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
Figure 3-1 C. Install stainless steel pop rivets into both sides of trim. D. Verify no sharp edges on stainless steel pop rivets. Figure 3-2 U.S. & Canada 1-800-922-1919 • Mexico 01-800-890-2900 • www.hussmann.com...
Page 31
To obtain warranty information or other support, contact your Hussmann representative. Please include the model and serial number of the product. Hussmann Corporation, Corporate Headquarters: Bridgeton, Missouri, U.S.A. 63044-2483 01 October 2012...
Page 32
Hussmann Corporation 12999 St. Charles Rock Road Bridgeton, MO 63044-2483 www.hussmann.com...