Sony HDPS-M10 Service Manual page 24

8) The HDPS-M10 will power off again when the "Upgrade
Status" bar reaches about 2/3 complete. As soon as "Please
power on device again." is displayed in the "Messages" pane,
press the POWER button within 25 seconds to power on the
unit.
9) When the firmware upgrade is completed, the "Firmware
Upgrade Successfully" popup window will be displayed. Then
click the "OK" button.
10) Click the "Exit" button to finish the "Firmware upgrade tool".
11) Important notice:
After the firmware upgrade is completed, the language will be
reset to English. So change the language to the preferred one,
please refer to "3-2-11-2. Language Settings" for the details.
After the firmware upgrade is completed, you are required to
fully charge the HDPS-M10 at least once.
Error Messages:
1) Firmware upgrade is not supported for the connected USB
device.
Cause: The HDPS-M10 drive is powered off or not detected
by the PC.
Solution: Press the POWER button on the HDPS-M10 and
ensure that it is detected by the PC. If necessary,
disconnect the HDPS-M10 from the USB port and
re-connect again.
2) The application is already running.
Cause: Another instance of the "Firmware upgrade tool" is
already running, or the previous instance has not
been completely closed.
Solution: Use the existing window of the upgrade tool. If there
is no existing window, please wait for 20 seconds
before restarting the "Firmware upgrade tool".
HDPS-M10
Fig. 3-1-28.
Fig. 3-1-29.
3) Time-out error. Please exit this utility and run it again.
Cause: The firmware upgrade operation timed out because
the POWER button was not pressed within 25
seconds when the "Please power on device again."
was displayed in the "Messages" pane.
Solution: Click the "Exit" button and power on the HDPS-
M10. Wait until the HDPS-M10 is detected by the
PC. The HDPS-M10 LCD screen icons may be
distorted. Run the "Firmware upgrade tool" again
and follow the "Firmware Upgrade" procedure
above. The LCD screen will return to normal when
the firmware upgrade is successful.
The figure shown below is an example of how the
distorted LCD screen icons may appear.
4) The new firmware version is older than (same as) the original
version. If you still want to update the firmware, please press
[YES]; otherwise press [NO].
Cause: The new firmware version is older than, or the same
as, the current version.
Solution: Click "YES" if your previous firmware upgrade
failed. Otherwise, you do not need to proceed with
this upgrade.
5) Stop to upgrade firmware.
Cause: This message will be displayed if "NO" is pressed
in the previous Error Message.
Solution: If you wish to continue with firmware upgrade, click
the "Start Upgrade Firmware" button. Click "Exit"
to exit the utility.
6) Device can't be detected. Please exit the utility and run the
utility again.
Cause: The HDPS-M10 was turned off before upgrade was
started.
Solution: Click "Exit" and turn on the HDPS-M10. Wait until
the HDPS-M10 is detected by the PC. Run the
"Firmware upgrade tool" again.
7) To get firmware version fail!
Cause: There is a miscommunication between the HDPS-
M10 and the upgrade tool.
Solution: Exit the tool and repeat the Upgrade Procedure.
8) The firmware code download fail!
Cause: There is a miscommunication between the HDPS-
M10 and the upgrade tool.
Solution: Exit the tool and repeat the Upgrade Procedure.
9) The firmware binary file doesn't exist!
Cause: The upgrade tool could not access the firmware
binary file.
Solution: Exit the tool and repeat the Upgrade Procedure.
Disconnect and re-connect the HDPS-M10 if
necessary.
10) Other error messages
Solution: Exit the tool and repeat the Upgrade Procedure.
Disconnect and re-connect the HDPS-M10 if
necessary.
3-13
Fig. 3-1-30.