Volume Adjustment; Mode Function - Stanley FATMAX FMCR001 Manual

ENGLISH
between 18 ° – 24 °C. DO NOT charge the battery pack in
an air temperature below +4.5 °C), or above +40 °C. This
is important and will prevent serious damage to the battery
pack.
The charger and battery pack may become warm to the
u
touch while charging. This is a normal condition, and
does not indicate a problem. To facilitate the cooling of
the battery pack after use, avoid placing the charger or
battery pack in a warm environment such as in a metal
shed or an uninsulated trailer.
If the battery pack does not charge properly:
u
Check operation of receptacle by plugging in a lamp
u
or other appliance;
Check to see if receptacle is connected to a light
u
switch which turns power off when you turn out
the lights;
Move the charger and battery pack to a location
u
where the surrounding air temperature is
approximately 18 ° – 24 °C;
If charging problems persist, take the tool, battery
u
pack and charger to your local service center.
The battery pack should be recharged when it fails to
u
produce sufficient power on jobs which were easily
done previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may also
charge a partially used pack whenever you desire with no
adverse effect on the battery pack.
Foreign materials of a conductive nature such as, but
u
not limited to, grinding dust, metal chips, steel wool,
aluminum foil, or any buildup of metallic particles
should be kept away from charger cavities. Unplug the
charger before attempting to clean.
Do not freeze or immerse the charger in water or any
u
other liquid.
Tool placement (fig. D)
Place the charger / radio on a smooth, level surface as shown
in Figure D.
On/Off - volume dial
To operate as a corded product, insert the AC plug (10)
u
into an appropriate AC power outlet or generator.
To operate as a cordless product, insert a fully charged
u
20v Max Stanley Fat Max battery (not included) into the
battery port (13) . Be sure battery is fully seated.
To turn the radio ON, press the ON/OFF - be sure battery
u
is latched and fully seated.
Press the ON/OFF - Volume dial again to turn the radio
u
OFF.

Volume adjustment

Rotate the ON/OFF - Volume dial (1) clockwise to increase
u
the volume.
8
(Original instructions)
To decrease the volume, rotate the ON/OFF - Volume dial
u
(1) counter clockwise.
Note: If the battery is attached to the radio and the AC plug is
plugged in at the same time, the radio will run off of the AC
power and not drain the battery. Having both attached
simultaneously will prompt the unit to charge the battery.

Mode function

To choose one of the mode functions (FM, AM, or AUX)
push the mode button (2) until the desired function is
displayed on the LCD. For example, if the radio is on FM,
push the mode button two times to change to AUX.
Note: The first press on any buttons when the back light is
off, will wake the unit up. Press the desired button again to
activate the function.
Tune or seek function
To tune:
Press and hold the right tune / seek button (8) to quickly
u
move the tuner up the frequency band. To move the
tuner down the frequency band, press the right tune/seek
button.
To seek:
Press and hold the left tune/seek button (8) , then release
u
to quickly scan up the frequency band to the next available
station. Press and hold the bottom tune/seek button (2) ,
then release to quickly seek down the frequency band.
To program the clock
The clock can be programmed with the power ON.
Press and hold the clock button (7) until the hour numbers
u
of the digital time flash on the LCD (5) , then release the
clock button.
Rotate the ON/OFF-Volume dial (1) left or right to
u
tune/seek buttons (8) to set hour.
When the correct hour is set, press the clock button
u
once so the minute numbers flash.
Rotate the ON/OFF-Volume dial (1) left or right to
u
tune/seek buttons (8) to set minutes.
If you do not press a button within 5 seconds, the clock
u
programming feature will automatically return to the
previous setting. The clock is set once the clock button
is re-pressed or if the numbers stop flashing.
To program the presets
6 FM and 6 AM radio stations may be independently set.
After programming the buttons, pressing the "1-6" preset
toggle button (4) will instantly change the frequency to the
preset station.