Subscribe to Our Youtube Channel
Related Manuals for United Electric Controls ONE Series
Summary of Contents for United Electric Controls ONE Series
- Page 1 Installation and Maintenance Instructions Pressure Differential Pressure Temperature IM1-03...
-
Page 2: Table Of Contents
Table of Contents Product Description Sensor Types Product Labeling Mounting Wiring Theory of Operation Setting of User Parameters Troubleshooting Frequently Asked Questions Dimensional Drawings Connections for Power Supply, IAW™ Output, and Solid State Relay... -
Page 3: Product Description
Please read all instructional literature carefully and thoroughly before starting. Refer to the final page for the listing of Recommended Practices, Liabilities, and Warrantees. Product Description... -
Page 4: Sensor Types
Sensor Types "... -
Page 5: Product Labeling
Product Labeling 1 H1 Mounting Tools Required... - Page 6 Electronics Housing Process Connections PRESSURE AND DIFFERENTIAL PRESSURE MODELS LOCAL AND REMOTE TEMPERATURE MODELS...
-
Page 7: Wiring
Wiring Tools Required Ground Connections for Products Beginning with D1D Power Supply Connections (Models D1A, D1B, & D1C only) - Page 8 Power Supply Connections for Products Beginning with D1D Primary Switched Output Connections (T ype D1A or D1B) Logic Solver Connection For 100mA Switched Output Solid State Relay Switched Output (Type D1C) Solid-State Relay Output Connections (Type D1D) IAW™ Output Connections &...
- Page 9 Logic Solver Connection For IAW™ Output Optional 4-20 mA Analog Process Signal Output Ω...
- Page 10 Summary of Wiring Connections With Switch Rating Code A With Switch Rating Code B With Switch Rating Code C With Switch Rating Code D...
-
Page 11: Theory Of Operation
Theory of Operation... - Page 12 Display diagnostic Displayed if process variable is: In Operating Mode In View/Edit Mode...
- Page 13 Ω Start Up Indication...
-
Page 14: Setting Of User Parameters
Setting of User Parameters Tools Required Switch Mode TO DISPLAY THE SWITCH MODE Mode Output Front Panel IAW™ Deadband Switch Status LED Switched Contacts "Flashes" Output "Pulses" TO CHANGE THE SWITCH MODE "... - Page 15 Set Point TO DISPLAY THE SET POINT TO CHANGE THE SET POINT VALUE Deadband TO DISPLAY THE DEADBAND VALUE...
- Page 16 TO SET THE DEADBAND VALUE -/+ Extreme Values TO DISPLAY THE -/+ EXTREME READINGS TO RESET BOTH THE -/+ EXTREME READINGS Unit # and Operating Range Replacement Parts /User Service...
-
Page 17: Troubleshooting
Troubleshooting A. There appears to be no power Question Answer Direction... - Page 18 B. The switched output does not appear to be functioning Question Answer Direction &...
- Page 19 Answer Question Direction C. The IAW™ output does not appear to be functioning...
- Page 20 D. The 4-20mA output signal does not appear to be functioning Direction Answer Question E. The display reads: VALUE > SET POINT F. The display reads: VALUE < SET POINT...
- Page 21 G. The display reads: OVERRANGE! H. The display reads: OUT OF RANGE! I. The display reads: CALL FOR SERVICE Table 1 Switch Output Modes: Mode Output “Closed” Deadband is Status & IAW Flash Example...
-
Page 22: Frequently Asked Questions
Q. Is the deadband of the One Series switch adjustable? Q. Can I set and test the One Series after it is installed? Q. Does the One Series offer DPST switch output? Q. Does the One Series meet the definition... - Page 23 One Series temperature switch? Q. Why are "dry contacts" sometimes preferred over a solid-state relay? Q. Can the One Series optional 4 to 20mA output be "spanned" or "ranged" at the instrument? Q. Is the IAW™ duty cycle of 25mS an issue for interfacing with a PLC? Q.
-
Page 24: Dimensional Drawings
Q. Does the One Series have a floating ground? Q. If the power is interrupted to the One Series, what is the state of the output during the power failure? Dimensional Drawings Diagram 1 Single Enclosure Configuration (D1A) "... - Page 25 Dimensional Drawings Diagram 2 Dual Enclosure, Junction Box Configuration (D1B and D1C) Diagram 3 115/230 VAC Power Supply Configuration (D1D)
-
Page 26: Connections For Power Supply, Iaw™ Output, And Solid State Relay
Connections for Power Supply, IAW™ Output, and Solid State Relay Diagram 4 Diagram 5 Diagram 6 Diagram 7... - Page 27 Diagram 8 Diagram 9 Diagram 10 Diagram 11 Diagram 12...
- Page 28 Diagram 13 Correction to Diagram 14 Terminal Block Connections Diagram 14 Terminal Block Connections (D1D or D1E) Standard With option M027 (free contact) LOAD SSR LOAD SSR INPUT LOAD LOAD VAC LOAD 4-20 See preceding 4-20 See preceding sections for sections for details details...
- Page 29 RECOMMENDED PRACTICES AND WARNINGS LIMITED WARRANTY OF REPAIR AND REPLACEMENT LIABILITY LIMITATION www.ueonline.com...
- Page 30 NOTE:...
- Page 31 NOTE:...
- Page 32 U.S. S ALES FFICES NTERNATIONAL FFICES www.ueonline.com...
Need help?
Do you have a question about the ONE Series and is the answer not in the manual?
Questions and answers