Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Vivitek DU6693Z
Summary of Contents for Vivitek DU6693Z
- Page 1 Remote Communicaton Manual DU6693Z...
-
Page 2: Table Of Contents
DU6693Z DLP Projector Remote Communication Manual Table of Contents The Serial Interface RS-232 Command ..................2 Communication parameter ......................2 Operation commands ......................... 2 Operation command syntax ....................2 List of operation commands ....................3 Simulated IR remote controller commands ................14 ... -
Page 3: The Serial Interface Rs-232 Command
DU6693Z DLP Projector Remote Communication Manual The Serial Interface RS-232 Command This projector supports to control by RS-232 command, there exists two types of RS-232 serial commands: Operation command: The commands are listed by the OSD menus structure as PICTURE,SIGNAL, SETUP, ... -
Page 4: List Of Operation Commands
DU6693Z DLP Projector Remote Communication Manual List of operation commands PICTURE OSD Function Operation Settings/Return Values Available when command Picture Mode pic.mode Projector is turned on. 0 = High Bright Input signal is detected 1 = Presentation 3D mode is turned off. - Page 5 DU6693Z DLP Projector Remote Communication Manual Advance/Input Balance green.offset Projector is turned on. /Green Offset 0-200 Input signal is detected. Advance/Input Balance blue.gain Projector is turned on. /Blue Offset 0-200 Input signal is detected. Projector is turned on.
- Page 6 DU6693Z DLP Projector Remote Communication Manual Advance/ HSG hsg.c.sat Projector is turned on. /Cyan/Saturation 0-200 Input signal is detected. Projector is turned on. Advance/ HSG hsg.m.sat /Magenta/Saturati on 0-200 Input signal is detected OSD Function Operation Settings/Return Values...
- Page 7 DU6693Z DLP Projector Remote Communication Manual SIGNAL OSD Function Operation Settings/Return Values Note command Input Select input.sel Projector is turned on. 0 = HDMI I 1 = DisplayPort 2 = DVI-D 3 = VGA 4 = Component / BNC...
- Page 8 DU6693Z DLP Projector Remote Communication Manual OSD Function Operation Settings/Return Values Note command Color Space color.space Projector is turned on. 0 = Auto The source is detected. 1 = YPbPr (Rec 709) 2 = YcbCr (Rec 601) 3 = RGB-PC (0-255)
- Page 9 DU6693Z DLP Projector Remote Communication Manual SETUP OSD Function Operation Settings/Return Values Note command Language lang Projector is turned on. 0 = English 1 = French 2 = Spanish 3 = German 4 = Portuguese 5 = Chinese Simplified...
- Page 10 DU6693Z DLP Projector Remote Communication Manual OSD Function Operation Settings/Return Values Note command Trigger1 trig.1 0 = Off Projector is turned on. 1 = On Trigger2 trig.2 0 = Off Projector is turned on. 1 = On Control Panel Lock keypad.lock...
- Page 11 DU6693Z DLP Projector Remote Communication Manual OSD Function Operation Settings/Return Values Note command Network Projector is turned on. IP Address net.ipaddr <string> Network Projector is turned on. Subnet Mask net.subnet <string> Network Projector is turned on. Gateway net.gateway...
- Page 12 DU6693Z DLP Projector Remote Communication Manual OSD Function Operation Settings/Return Values Note command Lens Setting lens.up.3 Projector is turned on. Lens Control Lens Lock is set to Off (0). Lens Setting lens.down Projector is turned on. Lens Control Lens Lock is set to Off (0).
- Page 13 DU6693Z DLP Projector Remote Communication Manual OSD Function Operation Settings/Return Values Note command Corner Adjustment 4corner.ulx 0 to 60 Projector is turned on. Horizontal direction of Adjusting Corner Adjustment will upper left corner reset the settings of. Keystone.
- Page 14 DU6693Z DLP Projector Remote Communication Manual SERVICE OSD Function Operation Settings/Return Values Note command Model model <String> Projector is turned on. Serial Number ser.no <String> Projector is turned on. Software Version sw.ver <String> Projector is turned on. ...
-
Page 15: Simulated Ir Remote Controller Commands
DU6693Z DLP Projector Remote Communication Manual Simulated IR remote controller commands This control command simulates the IR remote controller and its control keys. It shares the same syntax of operation command. It begins with characters "ky", followed by control commands and settings separated by space blank [SP], and ended by carriage return pair "CR"... -
Page 16: Control The Projector Through A Network
DU6693Z DLP Projector Remote Communication Manual Control the Projector Through a Network This projector supports the following methods in remotely controlling the projector through a network: Control projector through web browser. Control projector with RS-232 control or simulated IR commands via TCP/IP communication protocol. -
Page 17: Set Up The Projector For Networking
DU6693Z DLP Projector Remote Communication Manual Set up the projector for networking Before performing projector control by network, please configurate the network setting and make sure Standby Power is set to On. Network and RS-232 control are disabled if Standby Power is set to off for reducing the standby power consumption (less 0.5W). -
Page 18: Control The Projector Through A Network
DU6693Z DLP Projector Remote Communication Manual Control the projector through a network Control the projector through a web browser Open the web browser of your control PC; type the projector's IP address. The left of the web page shows below four options: Projector Status: Display current projector status and software information. - Page 19 DU6693Z DLP Projector Remote Communication Manual Crestron RoomView This page shows Crestron control page for projector control, the available options are as below options. Power: Press this button to turn power on or off. Source List: Switch projector input sources. Press the ▲ or ▼ arrow key to scroll through the dropdown list of...
- Page 20 DU6693Z DLP Projector Remote Communication Manual Control key window This window simulates keys on the remote controller and control panel. Enter: Confirm and select function options Menu: Press to display OSD menu. Press again to exit it. Auto: Run the auto image adjustment function.
-
Page 21: Control Projector With Tcp/Ip Communication Protocol
DU6693Z DLP Projector Remote Communication Manual Control projector with TCP/IP communication protocol This projector supports TCP/IP communication protocol which enables you to send RS-232 operation commands or simulated IR commands to control projectors connected with RJ45 cable via terminal connection application software, e.g. -
Page 22: About Vivitek Support
DU6693Z DLP Projector Remote Communication Manual About Vivitek Support If you cannot find solutions from this user guideline, please contact us using the contact information below: North and Central America VIVITEK USA 15700 Don Julian Road, Suite B, City of Industry, CA 91745, U.S.A.