Related Manuals for skyvoe OBX 32000
Summary of Contents for skyvoe OBX 32000
- Page 1 OBX 32000 / OBX 4270 Deck Post & Tilt Mount Assembly Manual *This deck post is shown with the tilt mount for OBX 32000 / OBX 4270*...
-
Page 3: Table Of Contents
PLATE POSITION AND ANCHORING ....... 9 POST TILT MOUNT ASSEMBLY ........13 PARTS FOR POST TILT MOUNT ........14 TILT MOUNTS ..............15 U-BOLTS AND MOUNTING PLATE ASSEMBLY ..... 16 TILT MOUNT ASSEMBLY ..........18 oBX 32000 / oBX 4270 anual... -
Page 5: Parts For Post Assembly
Parts for Post Assembly: back front this item is found in parts box Gather the following: 1. 1- Post 2. 1- Base Plate 3. 1 - Post Lock - Handle Not Included: Anchoring hardware for Base Plate oBX 32000 / oBX 4270 anual... -
Page 6: Tilt Mounts
Assembly Manual- Deck Post Tilt Mounts: The tilt mount portion of a portable cart is provided in a separate box labeled “PTM” and is size specific. See below for the appropriate sizes. 32” & 42” Class Televisions Tools Required for Post Assembly: 9/16”... -
Page 7: Post To Plate Assembly
Post to Plate Assembly: Upper Cable Entry Hole Lower Cable Exit Hole Hole Post Lock - Handle Located on side Set Screw Preinstalled Bottom of Post Brass Fitting for Friction Reduction oBX 32000 / oBX 4270 anual... - Page 8 Assembly Manual- Deck Post Slide bottom of post over the sleeve that is found towards the back of the mounting plate. Locate the post lock handle hole on the side of the post. Thread the handle into the hole. Do not tighten completely until post is in the preferred viewing position.
-
Page 9: Plate Position And Anchoring
Using the four holes indicated with the red ciricles, drill the holes for the hardware you purchased to secure the base plate to the deck or patio. After the holes are drilled insert your hardware and tighten securely. oBX 32000 / oBX 4270 anual... - Page 10 Assembly Manual- Deck Post You have now completed the assembly portion of your Deck Post Mount. You have now completed the assembly portion of your Deck Post Mount. Proceed to the box labeled: PTM-32 or PTM-42 to complete your installation. ®...
-
Page 11: Post Tilt Mount Assembly
Post Tilt Mount Assembly oBX 32000 / oBX 4270 ount anual... - Page 12 Assembly Manual- Post Tilt Mount Parts for Tilt Mount Assembly: these items are found in parts box 1. Previously assembled post: Deck Post, In-ground Post, or Portable Cart 2. 2- U-Bolts - (4) Flat Washers, (4) Lock Washers, (4) Powder Coated Nuts 3.
-
Page 13: Tilt Mounts
PTM Boxes will contain the following items: 2- Mounting Arms 2- M6 Carriage Bolts 1- Mounting Plate 2- ABS Washers 2- Tilt Control Knobs 2- Lock Washers Tools Required for PTM Assembly: 9/16” Ratchet with 9/16” Socket oBX 32000 / oBX 4270 ount anual... -
Page 14: U-Bolts And Mounting Plate Assembly
Assembly Manual- Post Tilt Mount U-Bolts and Mounting Plate Assembly: U-Bolt Post Saddle Top View U-Bolts should be hooked around the post and through the holes on the U-Bolt Saddles. These should be positioned near the upper cable entry hole. With U-Bolts and saddles in place, slide mounting plate over the U-bolt ends. - Page 15 3. Thread black powder coated nuts over bolt ends and hand tighten. See figure 3a for suggested mounting plate placement. 4. Once positioned, level and tighten all U-bolt nuts on mounting plate. 5. Place rubber bolt caps over exposed bolt ends oBX 32000 / oBX 4270 ount anual...
-
Page 16: Tilt Mount Assembly
Assembly Manual- Post Tilt Mount Tilt Mount Assembly: Gather the following: Tilt Control Knob M6 Bolts Lock Washer ABS Washer 1. Slide the M6 bolt through the hole on the Control Arm 2. Place the ABS washer on the thread side of the bolt. 3. - Page 17 Lay blanket down on flat sturdy surface. Run hand over sur- face to make sure there are no sharp object or protrusions, when the television is laying down. Lay television down, viewing side down on blanket. oBX 32000 / oBX 4270 ount anual...
- Page 18 Assembly Manual- Post Tilt Mount These will be in a separate Gather the clamping nuts with springs. bag shipped located with the User Manual Packet. Remove and set aside the 4 bolts and washers from each of the clamp nuts with springs.
- Page 19 Be sure to check that the mounting arms leveled with each other before attempting to mount the television. With both arms firmly secure to the television’s power struts you may proceed to the final mounting step. oBX 32000 / oBX 4270 ount anual...
- Page 20 Assembly Manual- Post Tilt Mount With the help from a friend, lift the television and attach the hooks on the mounting arms to the plate on the tilt mount. Tighten knobs on arms once the tilt is set correctly for the television. Once the television is hung on the plate.
Need help?
Do you have a question about the OBX 32000 and is the answer not in the manual?
Questions and answers