Advertisement
Quick Links
Advertisement
Related Manuals for Barco UST
Summary of Contents for Barco UST
- Page 1 UST lens for F-series Installation manual ENABLING BRIGHT OUTCOMES...
- Page 2 Barco NV Beneluxpark 21, 8500 Kortrijk, Belgium www.barco.com/en/support www.barco.com Registered office: Barco NV President Kennedypark 35, 8500 Kortrijk, Belgium www.barco.com/en/support www.barco.com...
- Page 3 General Overview • Preparation of the lens • Parts indication R5912118 /01 UST lens for F-series...
- Page 4 Image 1-1 • For F70: facing up and to the left Image 1-2 Do not use for projection to the left when mounted in a frame. • For F80: facing up and to the left R5912118 /01 UST lens for F-series...
- Page 5 Image 1-3 • For F90: facing up and to the right Image 1-4 Do not use for projection to the right when mounted in a frame. 30° 60° 30° 60° 0.38:1 Barco Image 1-5 R5912118 /01 UST lens for F-series...
-
Page 6: Required Tools
Place the lens on a table. Turn out the 6 screws (1). Use an Allen key with a long shaft so that you do not damage the screw head. These screws will not be reused. Note: Always use the correct tool (delivered with the kit) to avoid damage to the screw heads ! Image 1-7 R5912118 /01 UST lens for F-series... - Page 7 E.g. for an FS40 projector, you want to project to the left, then turn the motor housing until the left marking on the motor housing corresponds with the reference marking on the lens housing. R5912118 /01 UST lens for F-series...
- Page 8 Use again a tool with a long shaft (Allen key 2 mm, delivered with the kit). The lens is ready to be mounted on the projector. How your image is displayed Projection to the side for any projector: Image 1-12 Side view Top view R5912118 /01 UST lens for F-series...
- Page 9 Slide the lens adaptor on the lens input until it matches the motor housing (1). Make sure the contacts are on the left top of the adaptor. Image 1-14 Secure the adaptor by turning it to the right (bayonet fitting) (2). R5912118 /01 UST lens for F-series...
-
Page 10: Parts Indication
General 1.2 Parts indication Overview Image 1-15 Bottom plate, fixation screws depends on projector type 2th plate with 2 nuts 3th plate with 2 screws Clamp, with 2 screws R5912118 /01 UST lens for F-series... -
Page 11: Mounting The Lens
When mounting the lens without the support, always use a safety cable as shown in the image. Overview • When mounting the lens without the support • Mounting the UST lens on a F90 projector • Mounting the UST lens on a F70 projector • Mounting the UST lens on a F40 projector •... - Page 12 Secure the safety cable around the truss and secure the shackle by turning the safety ring of the shackle over the open end. 2.2 Mounting the UST lens on a F90 projector How to mount Turn the projector on its side or on its top cover.
- Page 13 Turn the projector back on its feet. Slide the lens locking system to the left. Insert the lens. Make sure the electric contact points (C) on the lens match the contact points on the lens holder. Image 2-3: Mounting lens R5912118 /01 UST lens for F-series...
- Page 14 Image 2-5: Mount 2nd plate Mount the 3th plate on the 2nd plate. Use the upper mounting holes in the 2nd plate. Drive in both screws but do not fasten yet. R5912118 /01 UST lens for F-series...
- Page 15 Fully fasten the screws of the 3th plate and the nuts of the 2nd plate so that the support is fully assembled. The projector is ready for use. 2.3 Mounting the UST lens on a F70 projector How to mount Turn the projector on its side or on its top cover.
- Page 16 Slide the lens locking system to the left. Insert the lens. Make sure the electric contact points (C) on the lens match the contact points on the lens holder. Image 2-9: Mount the lens R5912118 /01 UST lens for F-series...
- Page 17 Image 2-11: Mount the 2nd plate Mount the 3th plate on the 2nd plate. Use the upper mounting holes in the 2nd plate. Drive in both screws but do not fasten yet. R5912118 /01 UST lens for F-series...
- Page 18 Fully fasten the screws of the 3th plate and the nuts of the 2nd plate so that the support is fully assembled. The projector is ready for use. 2.4 Mounting the UST lens on a F40 projector How to mount Turn the projector on its side or on its top cover.
- Page 19 Turn the projector back on its feet. Slide the lens locking system to the left. Insert the lens. Make sure the electric contact points (C) on the lens match the contact points on the lens holder. R5912118 /01 UST lens for F-series...
- Page 20 Mounting the lens Image 2-15: Open locking system Image 2-16: Mounting lens R5912118 /01 UST lens for F-series...
- Page 21 Image 2-18: Mount the 2nd plate Mount the 3th plate on the 2nd plate. Use the lower mounting holes in the 2nd plate. Drive in both screws but do not fasten yet. R5912118 /01 UST lens for F-series...
- Page 22 Fully fasten the screws of the 3th plate and the nuts of the 2nd plate so that the support is fully assembled. The projector is ready for use. 2.5 Mounting the UST lens on a F80 projector Lens can also be used with an F80 mounted in its rigging frame.
- Page 23 Turn the projector back on its feet. Insert the prepared lens. Make sure the electric contact points (C) on the lens match the contact points on the lens holder. Turn the lens to the right to lock the bajonet closing. R5912118 /01 UST lens for F-series...
- Page 24 Image 2-24: Mount the 2nd plate Mount the 3th plate on the 2nd plate. Use the lower mounting holes in the 2nd plate. Drive in both screws but do not fasten yet. R5912118 /01 UST lens for F-series...
- Page 25 Fully secure both screws. Image 2-26: Mount clamp bracket Fully fasten the screws of the 3th plate and the nuts of the 2nd plate so that the support is fully assembled. The projector is ready for use. R5912118 /01 UST lens for F-series...
- Page 26 R5912118 /01 | 2019-10-21 Barco NV | Beneluxpark 21, 8500 Kortrijk, Belgium Registered office: Barco NV | President Kennedypark 35, 8500 Kortrijk, Belgium www.barco.com...