Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Goldair Platinum GPOC4310
Summary of Contents for Goldair Platinum GPOC4310
- Page 1 Operating Instructions 10 Fin Oil Column Heater Model: GPOC4310...
- Page 2 General Care and Safety Guide YOUR SAFETY IS IMPORTANT TO US. PLEASE ENSURE YOU TAKE NOTE OF THE INSTRUCTIONS AND WARNINGS OUTLINED IN THIS MANUAL. CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.
- Page 3 General Care and Safety Guide • Never use the appliance to dry clothes. • Always unplug appliance when not in use. • When the appliance has been unpacked, check it for transport damage and ensure all parts have been delivered. If parts are missing or the appliance has been damaged, contact the Customer Services Team.
- Page 4 General Care and Safety Guide • The appliance must not be immersed in any liquids. • There are no user serviceable parts installed in the unit. • Do not place the unit in wardrobes or other enclosed spaces as this may cause fire hazards.
- Page 5 Assembly WARNING: Heater must not be used without the castor plates and castors fitted. Before first use you need to set the castor wheels to the widest position. To do this slide each wheel out from the main body until they cannot go any further and then tighten the screws to lock them in position.
- Page 6 Operating Your Oil Column Heater Always choose a safe location for the heater, keeping in mind the safety precautions outlined. Ensure all packaging has been removed from the unit before use. Please follow the below instructions. WARNING: In order to avoid overheating or fire, do not cover the heater. WARNING: Keep all objects at least 1 metre from the front, sides and rear of the appliance.
-
Page 7: Control Panel
Operating Your Oil Column Heater CONTROL PANEL A. Thermostat button B. + Temperature & hours increase button C. Power/Mode button D. Timer button E. － Temperature & hours decrease button F. Power/stand-by button REMOTE CONTROL Check that the heat control switch is set to Off position before plugging the heater into the mains supply. -
Page 8: Turning Heater Off
Operating Your Oil Column Heater Press the Power/Mode (C) button and the heater will cycle through LOW, MED, HIGH and ECO modes. In the LOW, MED and HIGH modes the heater will continue to run uninterrupted as the thermostat does not work in these modes. SETTING THE TEMPERATURE ECO MODE ONLY Press the MODE button until the “ECO”... - Page 9 Operating Your Oil Column Heater SET THE TIMER TO AUTO-ON This function provides a delayed start option and should only be set if you want the heater to automatically turn ON after a certain period of time (1 to 24 hours from the time the function is set).
-
Page 10: Technical Specification
Model No: GPOC4310 Supply: 230-240VAC 50Hz Wattage: 2300-2400W SUPPORT AND TECHNICAL ADVICE Goldair – New Zealand Goldair – Australia Monday – Friday 8am-5pm Monday – Friday 8am-5pm Phone +64 (0)9 917 4000 Phone +61 (0)3 9365 5100 Phone 0800 232 633 Phone 1300 465 324 info@cdb.co.nz... -
Page 11: Three Year Warranty
In non-domestic use Goldair limits the voluntary warranty to three months. Goldair undertake to repair or replace this product at no charge if found to be defective due to a manufacturing fault during the warranty period. - Page 12 New Zealand PO Box 100707, North Shore Mail Centre, Auckland, 0745 www.goldair.co.nz Australia PO Box 574, South Morang, Victoria, 3752 www.goldair.com.au...
Need help?
Do you have a question about the Platinum GPOC4310 and is the answer not in the manual?
Questions and answers