Stihl HS 46 Instruction Manual
  1. Manuals
  2. Brands
  3. Stihl Manuals
  4. Trimmer
  5. 46
  6. Instruction manual

Stihl HS 46 Instruction Manual

Hide thumbs Also See for HS 46:
Table of Contents

Advertisement

Quick Links

STIHL HS 46, 56
Instruction Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HS 46 and is the answer not in the manual?

Questions and answers

Related Manuals for Stihl HS 46

Summary of Contents for Stihl HS 46

  • Page 1 STIHL HS 46, 56 Instruction Manual...

  • Page 3: Table Of Contents

    Dr. Nikolas Stihl Specifications Maintenance and Repairs Disposal EC Declaration of Conformity This instruction manual is protected by copyright. All rights reserved, especially the rights to reproduce, translate and process with electronic systems. HS 46, HS 46 C, HS 56 C...

  • Page 4: Guide To Using This Manual

    Warning where there is a risk of an endanger anyone. Ensure that the accident or personal injury or serious machine cannot be used without damage to property. authorization. HS 46, HS 46 C, HS 56 C...
  • Page 5 Only use cutting blades and accessories muffler and gear housing – risk of burns! that are explicitly approved for this power tool by STIHL or are technically identical. If you have any questions in HS 46, HS 46 C, HS 56 C...
  • Page 6 – serious or fatal warped), correctly mounted and must remain at a standstill when the burns could result! thoroughly sprayed with STIHL engine idles – throttle trigger released. resin solvent (lubricant) HS 46, HS 46 C, HS 56 C...
  • Page 7 Make sure you always have good Stop work immediately if you start balance and secure footing. suffering from nausea, headaches, impaired vision (e.g. your field of vision gets smaller), impaired hearing, HS 46, HS 46 C, HS 56 C...
  • Page 8 Wait for cutting blades to come to a – against wire fences, do not touch standstill wire with the cutting blades Do not touch electric power lines – never cut through electric power lines – risk of electrocution! HS 46, HS 46 C, HS 56 C...

  • Page 9: Using The Unit

    STIHL recommends the use of original STIHL replacement parts. They are specifically designed to match your model and meet your performance requirements. HS 46, HS 46 C, HS 56 C...

  • Page 10: Fuel

    Repeat the procedure several times on Gasoline wide hedges. Use only high-quality brand-name gasoline with a minimum octane rating of 90 – leaded or unleaded. HS 46, HS 46 C, HS 56 C...

  • Page 11: Fueling

    (100) 0.20 (200) 0.30 (300) 0.40 (400) 0.50 (500) Raise grip to vertical position. Use a canister approved for storing fuel. Pour oil into canister first, then add gasoline and mix thoroughly. HS 46, HS 46 C, HS 56 C...
  • Page 12 The marks on the tank cap and fuel tank STIHL recommends you use the STIHL are then in alignment. filler nozzle for fuel (special accessory). Fill the fuel tank. HS 46, HS 46 C, HS 56 C...

  • Page 13: Starting / Stopping The Engine

    Starting throttle n – this position is position – see section on "Closing". used to start a warm engine. The Master Control lever moves to the normal run position F when the throttle trigger is squeezed. HS 46, HS 46 C, HS 56 C...
  • Page 14 Master Control lever. that the cutting blades are not Press down the throttle trigger touching the ground or any other lockout and open the throttle – the obstacles. Master Control lever moves to the HS 46, HS 46 C, HS 56 C...

  • Page 15: Operating Instructions

    For longer out-of- service periods – see "Storing the Move the Master Control lever to n Machine". and continue cranking until the engine runs. HS 46, HS 46 C, HS 56 C...

  • Page 16: Cleaning The Air Filter

    WARNING If the cutting blades continue to run while the engine is idling, have your power tool checked and repaired by your servicing dealer. HS 46, HS 46 C, HS 56 C...

  • Page 17: Lubricating The Gearbox

    – Close the flap (1), top first, then the at a time (max. 5 g (1/5 oz)) while bottom, tabs (arrows) must snap turning the drive pinion (6) with a into position. HS 46, HS 46 C, HS 56 C...

  • Page 18: Storing The Machine

    Refit the filler plug and tighten it the rear handle) – out of the reach of Use STIHL gear lubricant for hedge down firmly. children and other unauthorized trimmers (special accessory) to lubricate persons. the blade drive gear. HS 46, HS 46 C, HS 56 C...

  • Page 19: Sharpening Instructions

    STIHL resin solvent. NOTICE Do not operate your machine with dull or damaged cutting blades. This may cause overload and will give unsatisfactory cutting results. HS 46, HS 46 C, HS 56 C...

  • Page 20: Maintenance And Care

    Spark plug Replace after every 100 operating hours Visual inspection Cooling inlets Clean All accessible screws and nuts (not adjust- Retighten ing screws) Visual inspection Anti-vibration elements Have replaced by servicing dealer HS 46, HS 46 C, HS 56 C...
  • Page 21 Have replaced by servicing dealer commercial use only – check every 25 Gearbox lubrication hours of operation and replenish with STIHL gear lubricant if necessary Safety labels Replace STIHL recommends an authorized STIHL servicing dealer HS 46, HS 46 C, HS 56 C...

  • Page 22: Minimize Wear And Avoid Damage

    Rewind starter – servicing dealer. Spark plug – STIHL recommends that you have Components of antivibration system – servicing and repair work carried out exclusively by an authorized STIHL HS 46, HS 46 C, HS 56 C...

  • Page 23: Main Parts

    14 Blade scabbard 15 Cutting blades (HS 46) 16 Cutting blades (HS 46 C) 17 Cutting blades (HS 56 C) 18 Blunt projection (integral cutter guard) 19 Cutter guard 20 Tip guard Serial number HS 46, HS 46 C, HS 56 C...

  • Page 24: Specifications

    Bidirectional, ground on one side the sound pressure level and sound Sharpening angle to power level; the K-factor in accordance horizontal: 35° with Directive 2006/42/EC is 2.0 m/s for the vibration level. HS 46, HS 46 C, HS 56 C...

  • Page 25: Maintenance And Repairs

    The logo and the STIHL parts symbol K type approval expires if the engine is (the symbol may appear alone on small modified in any way. parts). HS 46, HS 46 C, HS 56 C...

  • Page 26: Ec Declaration Of Conformity

    Directive 2000/14/EC, Annex V, and standard ISO 11094. Measured sound power level 105 dB(A) Guaranteed sound power level 107 dB(A) Technical documents deposited at: HS 46, HS 46 C, HS 56 C...
  • Page 28 0458-447-0121-C englisch www.stihl.com *04584470121C* 0458-447-0121-C...

This manual is also suitable for:

Hs 56Hs 82 seriesHs 82 rHs 82 rcHs 82 t

Table of Contents

Save PDF