Table of Contents
Advertisement
Quick Links
Road Light Kit
North American Groundsmaster 360 Multi-Purpose Machine with
Cab
Model No. 30517
Installation
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
5
6
7
8
Media and Additional Parts
Description
Installation instructions
Parts catalog
© 2011—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Description
No parts required
No parts required
Column bracket assembly
Column bracket mount
Carriage screw, 3/8 inch x 1 inch
Flange nut, 3/8 inch
Column cover
Screw
Dual rate flasher
Flange head screw, #10 x 3/4 inch
Flange nut, #10
Head light
Washer, .344 inch I.D.
Flange locknut, 5/16 inch
Warning light—front
Grommet
Warning light—rear
Screw, #10 x 1 inch
Flange lock nut, #10
Bullet connector
Wire harness
Grommet
Cable tie, 7–1/4 inch (184 mm)
Cable tie, 14–1/2 inch (368 mm)
No parts required
Register at www.Toro.com.
Qty.
–
–
1
1
2
2
1
2
1
2
2
2
2
2
2
2
2
4
4
8
1
1
13
2
–
Qty.
1
Use to install kit
1
Use to reference part numbers
Form No. 3366-955 Rev C
Installation Instructions
Use
Initial Preparation
Floor plate access hole
Install the switch column assembly
Install the dual rate flasher
Install the head lights
Install the warning lights
Install the wire harness
Final Procedures
Use
Original Instructions (EN)
Printed in the USA.
All Rights Reserved
Advertisement
Table of Contents
Related Manuals for Toro 30517
Summary of Contents for Toro 30517
- Page 1 Form No. 3366-955 Rev C Road Light Kit North American Groundsmaster 360 Multi-Purpose Machine with Model No. 30517 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Initial Preparation –...
-
Page 2: Initial Preparation
Initial Preparation No Parts Required Procedure 1. Park the machine on a level surface, stop the engine, engage the parking brake and remove the key from G015806 the ignition switch. Figure 2 2. Disconnect the negative (–) battery cable from the 1. - Page 3 G015966 Figure 4 1. 1 inch (51 mm) 3. 1–5/8 inches (41 mm) 2. 2 inch diameter (51 mm) Figure 5 1. Screw (2) 5. Column bracket 2. Column cover 6. Flange nut 3. Column bracket mount 7. Carriage screw 4.
- Page 4 Figure 7 1. Headlight 3. Washer 2. Headlight bracket 4. Flange lock nut G016296 Figure 6 1. Flange nut 3. Dual rate flasher 2. Flange head screw Installing the Warning Lights 2. Secure the dual rate flasher to the seat plate with (2) Parts needed for this procedure: #10 x 3/4 inch flange head screws and flange nuts (Figure 6).
- Page 5 Rear warning lights 1. Cut out the template on page 13. 2. On the rear of the cab headliner, use the template (Figure 10) to locate and mark the (3) mounting holes for each warning light (Figure 10). Figure 8 1.
- Page 6 Installing the Wire Harness g017760 Parts needed for this procedure: 4 5 6 Wire harness Figure 11 Grommet Right Side Cable tie, 7–1/4 inch (184 mm) 1. Light bulb w/double 4. Gray wire here filament Cable tie, 14–1/2 inch (368 mm) 2.
-
Page 7: Final Procedures
Figure 15 1. Cab harness and traction 2. Light kit harness unit harness Figure 14 – Plug the light kit wire harness into the cab and traction unit wire harnesses (Figure 15). 1. Cab connection 4. Harness clip 2. Switch connection 5. -
Page 8: Operation
Operation The Road Light Kit consists of 2 front mounted head lamps, 2 front warning lights and 2 rear warning lights. Light Switch Press the far side of the light switch (Figure 17) to activate the front head lights and the rear lights. Figure 16 1. -
Page 9: Aiming The Headlights
If turning RIGHT: The right combination warning/turn/tail lamp will illuminate as follows: • Amber lamp will flash. • The low intensity red tail lamp will be on steady. • The high intensity red tail lamp will be high rate flash. The left combination warning/turn/tail lamp will illuminate as follows: •... - Page 14 Notes:...
- Page 15 Notes:...