Page 1
PM SERIES LOUDSPEAKERS 4" AND 8" INSTALLATION INSTRUCTIONS PM Series Loudspeakers 4" and 8" Specifications are subject to change without notice AtlasSound.com...
Page 2
PM SERIES LOUDSPEAKERS 4" AND 8" INSTALLATION INSTRUCTIONS TABLE OF CONTENTS Specifications are subject to change without notice AtlasSound.com...
PM SERIES LOUDSPEAKERS 4" AND 8" INSTALLATION INSTRUCTIONS SAFETY INSTRUCTIONS Hearing Damage CAUTION: SUSPENSION & MOUNTING must A 5:1 Specifications are subject to change without notice AtlasSound.com...
Page 4
PM SERIES LOUDSPEAKERS 4" AND 8" INSTALLATION INSTRUCTIONS PM SERIES LOUDSPEAKERS FEATURES APPLICATIONS Specifications are subject to change without notice AtlasSound.com...
Page 5
PM SERIES LOUDSPEAKERS 4" AND 8" INSTALLATION INSTRUCTIONS INSTALLATION VIA MOUNTING CABLES (INCLUDED) General considerations and hardware recommendations CAUTION: materials and methods. 2. Locate suitable support structure in the area the speaker is to be installed. (Fig 7 and 8) Specifications are subject to change without notice AtlasSound.com...
Page 6
PM SERIES LOUDSPEAKERS 4" AND 8" INSTALLATION INSTRUCTIONS TOP COVER MOUNTING SCREWS (3) TOP COVER SIDE SCREW (2) FIG.1 FIG.2 Specifications are subject to change without notice AtlasSound.com...
Page 7
PM SERIES LOUDSPEAKERS 4" AND 8" INSTALLATION INSTRUCTIONS FIG.3 FIG.4 FIG.5 Specifications are subject to change without notice AtlasSound.com...
Page 8
PM SERIES LOUDSPEAKERS 4" AND 8" INSTALLATION INSTRUCTIONS SUPPORT CABLE SAFETY CABLE SUPPORT CABLE SAFETY CABLE FIG.8 FIG.7 Specifications are subject to change without notice AtlasSound.com...
Page 9
PM SERIES LOUDSPEAKERS 4" AND 8" INSTALLATION INSTRUCTIONS 2. Locate suitable support structure in the area the speaker is to be installed. with the included mounting screw. (Fig. 9) 7. Route the speaker cable through the down pipe and connect to the appropriate terminals.
PM SERIES LOUDSPEAKERS 4" AND 8" INSTALLATION INSTRUCTIONS SPECIFICATIONS ENCLOSURE POWER FREQUENCY SENSITIVITY DISPERSION WOOFER MODEL 70.7V TAPS WOOFER HF DRIVER DIMENSIONS WEIGHT VOLUME RATING RESPONSE ANGLE MAG. WT. 150W OMNI TROUBLESHOOTING PROBLEM POSSIBLE CAUSE REMEDY Specifications are subject to change without notice...
Page 11
PM SERIES LOUDSPEAKERS 4" AND 8" INSTALLATION INSTRUCTIONS NOTES Specifications are subject to change without notice AtlasSound.com...
Page 12
PM SERIES LOUDSPEAKERS 4" AND 8" INSTALLATION INSTRUCTIONS Specifications are subject to change without notice AtlasSound.com...
Page 13
PM Series Pendant Mount Loudspeakers Safety Instructions Please Read Carefully Before Installing or Operating Hearing Damage CAUTION: Suspension & Mounting TELEPHONE: (800) 876-3333 1601 JACK MCKAY BLVD. AtlasSound.com FAX (800) 765-3435 ENNIS, TEXAS 75119 U.S.A.
Page 14
PM Series Pendant Mount Loudspeakers Installation Via Mounting Cables (Included) General considerations and hardware recommendations CAUTION: CAUTION: When in doubt contact a qualified structural/mechanical engineer for approval of the mounting materials and methods. Note: If the speaker is being installed outdoors, seal plug with RTV silicone to prevent moisture from entering speaker.
Page 15
PM Series Pendant Mount Loudspeakers Figure 1 Figure 2 TELEPHONE: (800) 876-3333 1601 JACK MCKAY BLVD. AtlasSound.com FAX (800) 765-3435 ENNIS, TEXAS 75119 U.S.A.
Page 16
PM Series Pendant Mount Loudspeakers Figure 3 Figure 4 Figure 5 TELEPHONE: (800) 876-3333 1601 JACK MCKAY BLVD. AtlasSound.com FAX (800) 765-3435 ENNIS, TEXAS 75119 U.S.A.
Page 17
PM Series Pendant Mount Loudspeakers Figure 6a Figure 6b Figure 8 Figure 7 TELEPHONE: (800) 876-3333 1601 JACK MCKAY BLVD. AtlasSound.com FAX (800) 765-3435 ENNIS, TEXAS 75119 U.S.A.
Page 18
PM Series Pendant Mount Loudspeakers Suspended Installation Via Down Pipe (Not-Included) Using ⁄ " Diameter Ceiling Fan Hardware Figure 9 TELEPHONE: (800) 876-3333 1601 JACK MCKAY BLVD. AtlasSound.com FAX (800) 765-3435 ENNIS, TEXAS 75119 U.S.A.
Page 19
PM Series Pendant Mount Loudspeakers Troubleshooting PROBLEM POSSIBLE CAUSE REMEDY There is no sound Power off. Equipment setting is wrong. Assure that power is applied to all equipment in system. Volume set too low. Check that routing (input/output) controls are set correctly.
Need help?
Do you have a question about the PM Series and is the answer not in the manual?
Questions and answers