Download Print this page

Advertisement

Quick Links

®
HEALTH
If you have a problem, question, or request, call
your local dealer, or Steelcase Line 1 at
888.STEELCASE (888.783.3522)
for immediate action by people who want to help you.
(Outside the U.S.A., Canada, Mexico, Puerto Rico,
and the U.S. Virgin Islands, call: 1.616.247.2500)
Or visit our website: www.steelcase.com
©
2014 Steelcase Inc.
Grand Rapids, MI 49501
U.S.A.
Printed in U.S.A.
Regard
Media/Desk Cabinets* and Freestanding Tables
*Note: Assemble cabinets prior to seating and power elements, if applicable.
Media Cabinet
Freestanding
Table

Table of Contents

Topic
Base Frame for Wall-Mount
Freestanding Tables
1-7/8"
Desk Cabinet
Page
2 - 3
4 - 6
7 - 8
9
10
11
12
Protective Covering
Doc # 135357
939599300 Rev C
#2 Phillips Bit
with Extension
1/4"
Page 1 of 13

Advertisement

loading
Need help?

Need help?

Do you have a question about the Regard Media Cabinet and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Steelcase Regard Media Cabinet

  • Page 1: Table Of Contents

    Base Frame Extension 2 - 3 Base Frame for Wall-Mount 4 - 6 If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at Desk Cabinet Assembly 7 - 8 888.STEELCASE (888.783.3522) Media Cabinet Assembly for immediate action by people who want to help you.
  • Page 2: Base Frame Extension

    ® HEALTH LEG HERE Base Frame Extension Assembly for IN STEP 4 Cabinets (11”D) LINK Remove packaged aluminum trim and set aside. Trim will be assembled later. Place the Extension Frame and Link on a clean surface adjacent to the mating Base Frame. Two legs will be transferred from the mating Base LEG HERE Frame to the Extension Frame.
  • Page 3 ® HEALTH Adjust glides to level base assembly. Proceed to Desk Cabinet or Media Cabinet assembly pages in this document. GLIDE ADJUST THUMBWHEEL NOTE: Clevis pins will be loose until base frame trim is installed later. Page 3 of 13 Doc # 135357 939599300 Rev C...
  • Page 4 Regard product attaches to and must verify the adequancy of the mounting Toggle Bolt (2-1/2" - 3" Long) solutions, even if provided by Steelcase. #10 x 3" Wood Stud Screw The building owner or designated agent is responsible for verifying that the...
  • Page 5 ® HEALTH Wall Mounting Requirements for Non-Seismic Applications* (continued) *The building’s Engineer of Record must be 7.7” 6.5” consulted to determine if there are any 6.0” for Solid Surface* seismic requirements. Laminate Worksurface *Solid Surface Worksurface optional Center of Gravity Center of Gravity Bag Bin 18.9”...
  • Page 6 ® HEALTH LINK LEG HERE IN STEP 4 Base Frame Wall Assembly Remove the packaged aluminum trim and set aside. Place the frame and link on a clean surface adjacent to the wall. Remove leg attachment bolt from top of legs. TRIM LEG HERE Insert 2 legs into clevis brackets at the corners of...
  • Page 7 ® HEALTH Remove both pins from the link to separate it from LINK the frame. Hold link against marked wall and fasten it to the wall using one of the methods listed on “Wall Mounting Requirements” on Page 4. FRAME Reinstall clevis link pins to connect link to frame.
  • Page 8: Desk Cabinet Assembly

    ® HEALTH Desk Cabinet Assembly Place unit on a clean surface with front facing down. Remove both shipping brackets from the bottom of the cabinet. (Requires two people) Align and place unit on top of Base Frame. From under the Base Frame, install clamp REAR OF brackets with fasteners, making sure each CABINET...
  • Page 9 ® HEALTH Display Shelf Option: Insert two (2) flanged screws per shelf into pre-drilled holes in back panel. Hook display shelves over rear flanged screws and snap side flanges over pre-installed spring buttons. Spring buttons Task Light Option: Refer to Assembly Directions included with the task light.
  • Page 10: Media Cabinet Assembly

    ® HEALTH Media Cabinet Assembly Place unit on a clean surface with front facing up. Remove both shipping brackets from the bottom of the cabinet. (Requires two people) Align and place unit on top of Base Frame. From under the base frame, install the clamp brackets with fasteners, making sure each bracket is fully engaged with the frame and tighten securely.
  • Page 11: Base Trim Assembly

    ® HEALTH Note: cutout end here Base Trim Assembly TRIM Insert one end of the long trim onto one leg (1a) and on the other end, use a flat-bladed screwdriver to depress the spring-loaded plastic plunger of that leg using bottom slots provided (1b).
  • Page 12: Power Module Assembly

    ® HEALTH Mounting Power Module to Desk Cabinet Worksurface Pass power cord through opening in the cover. Power Module Fully extend clamp brackets. Tighten thumb screws on the back side of the cover making sure that the faceplate of the power module is properly aligned in the opening.
  • Page 13 ® WORKSURFACE COLUMN SUPPORT HEALTH Freestanding Table Assembly Place the worksurface on a clean surface making sure that the bottom (with pre-drilled holes) is facing up. Install top plate to worksurface column support with fasteners provided and tighten securely. Note TOP PLATE the direction of the countersunk holes.

This manual is also suitable for:

Regard desk cabinetRegard freestanding table