Operation; Maintenance - Novy Fusion 680 Operating And Installation Instructions

3. OPERATION

The controls are on the rotating valve.
Open the glass cover by turning it towards you.
① switch on / off
② decrease speed levels
③ and ④ LED indication speed level
⑤ increase speed levels
⑥ illumination
3.1 Extraction
Switch on – switch off
To switch the motor on push button ①.
The hood will always resume the level it was previously
switched off in.
Switch off with 10 minute delay:
Press button ① once. The first green LED blinks, the
other LED's remain lit up according to the level
in use. After 10 minutes motor and illumination switch
off automatically.
Auto-Stop
To avoid that the hood will function during a too long
period, it will switch off automatically after 3 hours
(when no changes to the controls have been made).
Motor and lighting will turn off automatically.
Switch off without delay:
Push button ① twice.
Levels of intensity
To decrease speed levels push button ②. To increase
speed levels push button ⑤.
Three green LED's ③ indicate level 1 to 3, one red LED
④ indicates the level 'POWER'.
POWER' is only used in case of excessive formation of
smoke, fumes or odours. Taking into account the large
volume of air which is extracted from the room at this
level, it's use should be limited.
'POWER' automatically reverts to level 3 after 6 min-
utes.
A self-rectifying thermal contact makes sure that
the motor is switched off when overheated. The mo-
tor will switch on again after is has cooled down. The
cause of the overheating needs to be determined. This
may be, for example, that the contents of the pan have
caught fire, the motor fan is blocked or an object is
(partly) closing off the exhaust opening.
3.2 Lightning
To activate the lights press button ④. The lights will
switch on at full power. Lighting can be activated inde-
pendently from the mo tor.
Dimming the LED lighting
When the LED lighting is on you can dimming by press-
ing and holding button 4.
3.3 Recirculation (option)
Programme recirculation
When choosing for recirculation, always set the recircu-
lation program on the hood. Execute this programming
as follows:
• Do the programming with the motor switched off.
• Simultaneously press the + and the – keys for 5
seconds until the red indicator lamp flashes 5 times.
The following functions have now been enabled:
• The run-out time has been set to 30 minutes (in-
stead of the default 10 minutes). Make use of the 30
minutes run-out time.
• The cleaning indicator for the Monoblock recircula-
tion filter has been set to 400 operating hours. After
400 working hours the red LED lights up. This is the
indication to clean the Monoblock recirculation filter
(see instructions on Maintenance).
Deactivate the recirculation:
• The motor must be switched off.
• Simultaneously press the [ + ] and the [ – ] keys on
thehood for 5 seconds until the third green LED
flashes 5 times.
3.4 InTouch
The extraction hood has the InTouch function. If you
have an induction hob from Novy with InTouch, you can
operate the extraction hood from the hob. The extrac-
tion hood can also be operated with a remote control
(accessory).
The InTouch function is switched off by default. The
function can be switched on by pressing the 1 key and
3 key at the same time for 3 seconds. The 2nd and 3rd
LEDs flash 3 times to confirm. (The unit must be
switched off).
To switch the InTouch function off press the 1 key and
2 key at the same time for 3 seconds. The 2nd and 3rd
LEDs flash 3 times to confirm. (The unit must be
switched off).
You can find more information about using the InTouch
functions in the InTouch manual for the hob or remote
control.

4. Maintenance

4.1 Grease filter
The cooker hood contains 2 or 3 metal grease filters,
dependent on the type number.
Grease filter indication
Indication: 4 flashing LEDs
After 20 cooking hours, the 4 LEDs will start to blink
during 5 minutes, this indicates that the grease filter
has to be cleaned.
EN 12