Table of Contents
Advertisement
Troubleshooting
If
you
are
having problems,
check
the
cOlUltermeasures
for
each
symptom
listed
below.
Ii
the
problem
still
cannot
be solved,
contact
your nearest
service
facility.
Symptom
,
Check and countermeasure
"
No
picture
• Check if
the
indicator
of
the
ON/OFF switch
is
lit.
If
not,
make
sure
the
power cord
is
cormected and press the
ON
JOFF
switch.
•
Check
if the monitor/projector
is
turned
on.
•
Check if
the
OUT
indicato
r matching the
monitor/
projector
is
lit
(see
page 49).
•
Check
if the monitor
/
projector
is
connected securely using the built-in
test patterns.
•
Check
if the correct INPUT
SELECT
button has been
pressed.
•
Check
if the input
source equipment
is
turned on and input source
is
being
played.
•
Check
if one
of
the
IN
indicators
is
lit.
If not, make
sure the input
source
equipment
is
connected correctly.
If
equipment
is
connected
to
VIDEO
3
IN, set
the SYNC AUTO/ON G
selector
to
AUTO.
If
equipment
is
connected
to VIDEO
2
IN,
check if the
NORMAL/COMP
selector
is
set to
the
correct position.
The
sync
signal streaks
on
the
•
If the
VIDEO
OUT D-sub connector is
used,
check to
see
if the RGB
/
YBR selector
and
screen
(does
not
stabilize).
SYNC SEP
/
COMP
selector
of
the
VIDEO OUT section
are
correct.
Picture
is
greenish.
•
If the
input
source
equipment
is
a
computer
connected
to VIDEO
3 IN,
set
the SYNC
AUTO/
ON
G
selector
to
ON
G.
• Equipment which
emits
both
external
sync signals and
sync
on
green signals cannot be
connected
to
VIDEO
2 IN connectors.
When
connecting Silicon Graphics
Inc.
computers or
some
Macintosh
models,
connect them to
VIDEO
3
IN
connectors and set
the
SYNC
AUTO/ON G
selector to
ON
G.
Picture
is
purplish.
•
If
the input
source equipment is a computer
connected to VIDEO
3 IN, set
the
RGB/
YBR
selector to RGB.
Picture
is
too
large.
•
Adjust
the size
of
the
picture using the SIZE
buttons.
•
Press
the
200M
-
button to set the
zooming
size to
xl.
Picture
is
enlarged
vertically.
• When
the
output format
is
108m, the picture is enlarged
if output to
a
monitor with the
conventional
Japanese
HDTV
format (1035i format).
In
this case,
set
the 1035/ 1080
format
selectoi of
the
monitor to
1080,
or
adjust
the
vertical
size using the
V SIZE
+ / -
button.
Remote commander does not
•
Check the type
of
your
remote
commander and set
the COMMAND
MODE
selector
function.
correctly (see page
4.2).
• nus
Wlit
functions with
remote
commanders for
Sony
TVs and projectors
only.
•
Disconnect the plug from
the
CTRL S IN
jack.
Remote
commander
malfunctions.
•
Set
the COMMAND
MODE
selector to
OFF.
The
POWER
indicator flashes.
• The built-in
thermal protector may
have
functioned. Check if the
surrOlUlding
temperature
is
too
high.
•
Press the
.
P OWER
switch
to
turn
the
Wlit
off.
Then press it again and check
the
POWER
indicator.
If
the
POWER
indicator still
flashes,
consult
your
dealer.
•
Press
the
POWER
switch
to
turn
the tmit off. Then press
it
again and check the fan. If the
fan does not
work, consult
your
dealer.
"NOT
APPUCABLE" is displayed on
• You have pressed a button that does
not
function in the
cWTent
operating mode.
the
screen.
"NO
REFERENCE"
is
displayed
on
• The black burst signal is
not
input to the VIDEO 1 W connector
when
GEN
LOCK
is
set to
the
screen,
and
the
GEN-LOCK
ON
on
the
MENU
2
screen.
indicator
on the
front panel flashes.
"WRONG
REFERENCE"
is
displayed
• The
format of the blade burst signal input from
the
signal
generator
does not corCf!spond
with
on
the
screen,
and the
GEN-LQCK
the
output
signal format (NTSC or PAL)
of the
converter.
indicator
on
the
frontpane1
flashes.
47
,
- Quick Links:
- Table of Contents
- Features
Hide quick links:
Advertisement
Table of Contents
