Table of Contents
Advertisement
Quick Links
B2880C2/B2880C2S
///
Transport TX28
Revision 1.0
Copyright © TYAN Computer Corporation, 2002-2003. All rights reserved. No
part of this manual may be reproduced or translated without prior written
consent from TYAN Computer Corp.
All registered and unregistered trademarks and company names contained in
this manual are property of their respective owners including, but not limited to
the following.
TYAN, Thunder K8S S2880UGNR, Transport B2880C2, B2880C2S, Transport
TX28 are trademarks of TYAN Computer Corporation.
AMD, Opteron and combinations thereof are trademarks of AMD Corporation.
AMI, AMIBIOS are trademarks of AMI Software Incorporated.
Microsoft, Windows are trademarks of Microsoft Corporation..
QLogic, Zircon, and combinations thereof are trademarks of QLogic
Corporation.
IBM, PC, AT, PS/2 are trademarks of IBM Corporation.
Winbond is a trademark of Winbond Electronics Corporation.
Portable Document Format (PDF) is a trademark of Adobe Corporation.
Information contained in this document is furnished by TYAN Computer
Corporation and has been reviewed for accuracy and reliability prior to printing.
TYAN assumes no liability whatsoever, and disclaims any express or implied
warranty, relating to sale and/or use of TYAN products including liability or
warranties relating to fitness for a particular purpose or merchantability. TYAN
retains the right to make changes to product descriptions and/or specifications
at any time, without notice. In no event will TYAN be held liable for any direct or
indirect, incidental or consequential damage, loss of use, loss of data or other
malady resulting from errors or inaccuracies of information contained in this
document.
1
http://www.tyan.com
Advertisement
Table of Contents
Related Manuals for TYAN Transport TX28
Summary of Contents for TYAN Transport TX28
- Page 1 In no event will TYAN be held liable for any direct or indirect, incidental or consequential damage, loss of use, loss of data or other malady resulting from errors or inaccuracies of information contained in this document.
-
Page 2: Table Of Contents
..……………………………………Page 20 Chapter 3: SCSI Backplane User Manual ..…..………………………………..Page 21 3.0 Before you begin ..…………………………………..Page 21 3.1 Backplane Specifications …...…..…………………………….Page 21 3.2 Backplane Layout ..…………………………………..Page 22 3.3 Pin Assignment ..…………………………………..Page 23 Appendix ...……………………………………Page 25 Safety Document of system …...…………………………………Page 25 http://www.tyan.com... - Page 3 German voltage) 1 x Thunder K8S (S2880) User’s Manual 1 x Transport B2880C2S User’s Manual 1 x Thunder K8S (S2880) Quick Reference 1 x TYAN driver CD 1 x screw 1 x 3-slot riser card 2 x Ultra320 SCSI backplanes (pre-installed)
- Page 4 1 x SATA drive power adapter 2 x SATA cables If any of these items are missing, please contact your vendor/dealer for replacement before continuing with the installation process. http://www.tyan.com...
-
Page 5: Chapter 1: Introduction
The Thunder K8S also offers rich features such as: dual channel Ultra320 ® SCSI controller, dual channel Gigabit Ethernet ports, ATI RAGE XL onboard video. Remember to visit TYAN’s Website at http://www.tyan.com. There you can find information on all of TYAN’s products with FAQs, distributors list and BIOS setting explanations. http://www.tyan.com... -
Page 6: Hardware Specifications
• Connects to PCI-X bridge A • One 64-bit riser card • Available in B2880C2S • Sliding rail and mounting brackets Integrated LAN Controllers TYAN reserves the right to add support ® • Broadcom BCM5704C dual channel or discontinue support for any OS GbE LAN: without notice. -
Page 7: Front View
CD-ROM Drive Drive 3.5” HDD Drive Power/HDD LEDs Cages (x6) Power/Reset Switches 1.4 - Rear view PS/2 Power Add-on PCI Serial Mouse (top) Supply Expansion Slots Ports Port Port K/B (bottom) (redundant w/LED shown Double-deck here) USB 1.1 Ports http://www.tyan.com... -
Page 8: Top View
1.5– Top View Memory Slots Cooling Riser EPS 12V CPU2 fans (x4) Card CPU1 HDD Drive CD-ROM SCSI backplanes Cages (x6) (top) (bottom) (x2) (available B2880C2S) http://www.tyan.com... -
Page 9: Chapter 2: Hardware Installation
(i.e. power supply case). For the safest conditions, Tyan recommends wearing a static safety wrist strap. (2) Avoid touching the motherboard components, IC chips, connectors, memory modules, and leads. -
Page 10: Opening The Chassis
Remove screw (x1) on the top of the chassis. 2.1.2 Remove screws (x2) on the rear of the chassis. 2.1.3 Pull the top cover from rear. 2.1.4 Lift up the top cover and remove it from the chassis. 2.1.5 Top cover removed. http://www.tyan.com... -
Page 11: Installing Hdd
2.2.1.2 Remove HDD tray from the chassis. 2.2.2 Picture of HDD tray. 2.2.3 Secure the drive with 4 screws from both sides of the tray. 2.2.4 Slide the tray back into the chassis. http://www.tyan.com... - Page 12 2.2.5 Secure the drive and tray by locking the handle into position. 2.2.6 Repeat 2.2.1 through 2.2.5 for installing other hard disk drive(s) if necessary http://www.tyan.com...
-
Page 13: Installing Fdd
Slide the drive into the cage and secure FDD onto cage by tightening screws (x4; 2 on each side). 2.3.5 Slide the cage with drive on the top of the CD-ROM drive. 2.3.6 Secure the cage onto chassis by tightening the screw removed in 2.3.1. http://www.tyan.com... - Page 14 2.3.7 Connect the data cable to FDD. 2.3.8 Connect the power cable to FDD. http://www.tyan.com...
-
Page 15: Installing Cd-Rom
2.4.1.2 Remove two screws on the chassis to take out the CD-ROM drive bay cover. 2.4.2 Slide the CD-ROM into the drive bay. 2.4.3 Connect the data cable to CD-ROM. 2.4.4 Connect the power cable to CD-ROM. http://www.tyan.com... - Page 16 2.4.5 Secure the CD-ROM drive to the chassis through the screw holes on the chassis bottom. http://www.tyan.com...
-
Page 17: Installing Processor(S) And Heatsink(S)
Your processor is installed 2.5.7 Repeat these steps for any additional processor if you are using two processors . 2.5.8 For installing the heatsink(s), please refer to Page 26 and 27 of the motherboard user’s manual for further details. http://www.tyan.com... -
Page 18: Installing Add-On Pci Card
The speed is 64bit/66MHz. 2.6.3 Place the add-on card to the desired slot. 2.6.4 Plug your PCI/PCI-X add-on card firmly into the PCI socket slot on the riser card. 2.6.5 Secure Add-on card by tightening the screw from the side. http://www.tyan.com... -
Page 19: Installing Memory Modules
Note: Please make sure to read through M/B User’s Manual before your start installing memory modules. 2.7.1 Insert the DIMM modules into the memory slots, starting with memory slots associated with CPU1. 2.7.2 Press down on the memory modules until it locks into place. http://www.tyan.com... -
Page 20: Finishing Up
In the rare circumstance that you have experienced difficulty, you can find help by asking your vendor for assistance. If they are not available for assistance, please find setup information and documentation online at our website or by calling your vendor’s support line. http://www.tyan.com... -
Page 21: Chapter 3: Scsi Backplane User Manual
Fan alarm control (DS4 SW4 and SW5 ): DS4 SW4 ON Fan 1 ( J9 ) alarm enable (DS4 SW5 OFF), alarm disable ( DS4 SW5 ON ) Temperature Setting (DS4 SW6): 50? (DS4 SW6 ON) 60? (DS4 SW6 OFF) Support Hot plug function http://www.tyan.com... -
Page 22: Backplane Layout
J8 J7 (DC U1/U2/U3 (On power in) board terminators) DS4 (function setting J9 (FAN 1 Connector) DS1 (setting HD#1 ID JP2 (to DS2 (setting HD#2 ID display Board DS3 (setting HD#3 ID connector) J2 (SCSI OUT To next backplane) http://www.tyan.com... -
Page 23: Pin Assignment
Device3 Power LED + Pin 11 Device3 Access LED + Pin 12 Device3 Access LED - Pin 13 Fail LED - Pin 14 Fail LED + Pin 15 Pin 16 KEY pin Pin 17 Reset - Pin 18 Reset + http://www.tyan.com... - Page 24 3.3.4 Fan1 pin out, J6 SENSOR 3.3.5 Power pin out, J7 and J8 http://www.tyan.com...
- Page 25 Appendix 1: Safety document of Tyan B2880C2/B2880C2S Notice for the USA Compliance Information Statement (Declaration of Conformity Procedure) DoC FCC Part 15: This device complies with part 15 of the FCC Rules Operation is subject to the following conditions: This device may not cause harmful interference, and This device must accept any interference received including interference that may cause undesired operation.
Need help?
Do you have a question about the Transport TX28 and is the answer not in the manual?
Questions and answers