Contact Closure, RS232[MegaTec], Phoenixtec], SEC 2400, SEC 9600, Megatec Three Phase, ..etc. NetAgentA provides a simple and easy installation procedure. CD provides along with NetAgentA offers several software to allow the user to configure IP address; central monitoring and multi shutdown on different operating systems. Other advance configurations could be accomplished in the Web browser.
UPS condition by a computer with Browser installed. The manager could monitor and control the UPS by simply input the IP address of the NetAgentA which connects to the UPS. When there is a power abnormal condition happens, the NetAgentA could also send the trap information to the system manager to take proper action.
Chapter 2. NetAgentA Series 2.1 NetAgentA Mini Models NetAgentA Mini Model Model Name Package Contents Internal External RJ45 RS232 Single Three Phase Phase 1. NetAgentAA Mini SNMP Card 2. NetAgentA Utility CD DA520 Quick Installation Guide (Optional) 1. NetAgentAA Mini SNMP Card 2.
Page 8
Green Blue Power Communication Flashing Sending/Receiving Normal Power Data UPS connection Flashing Lost Connecting connection with UPS Yellow NetAgentA Mini 9 Status Stop Operating Working Power Lost Writing Status Communication Firmware Yellow NetAgentA Mini 9 Status Flashing Flashing Communication Green...
Chapter 3 Software Installation Software Installation NetAgentA Utility CD offers several management and shutdown software. Insert CD into CD-ROM and software can be select under 【Program Installation】 Netility: Configure and Search NetAgentA. Refer to 4.3 ClientMate: Shutdown OS Software .
Chapter 4. NetAgentA Setting 4.1 Introduction NetAgentA can be login via web or HyperTerminal with protocol and encryption of HTTP/HTTPS/SSH/Telnet. Enter the IP address of NetAgentA to configure and monitor the UPS status. HTTP HTTPS TELNET 4.2 NetAgentA Login Procedure 1.
Page 11
7.Enter other parameter on NetAgentA webpage NOTE 1:Each NetAgentA has its unique serial number / MAC address and Password. This is available on the label of each unit. This helps to identify the card information on Netility NOTE 2: NetAgentA with LCD display may obtain the IP info from it.
Page 12
When NetAgentA IP is known, enter such IP address on the browser to login. If non-LCD NetAgentA model, install Netility software to find and configure its IP address.
Netility Installation Netility is tool software that helps the user to search all the available NetAgentA within network as well as to configure IP address and firmware upgrade. Mount the NetAgentA Utility CD on CD-ROM and click on Program Installation>Netility>Windows...
Page 14
Netility Operation and Setting Netlity main pages divided into 2 sections: 1. Online NetAgentA List 2. Function Selection 2. Function 1. Online NetAgentA List 2.5 Refresh List 2.4 About 2.3 Firmware Upgrade 2.2 Network Settings 2.1 Launch Web User Interface 1.2 Individual NetAgentA Info...
Page 15
When open up Netility , it automatically searches all the available online NetAegntA within the network with its serial number, IP address, MAC address. Double click on the specific NetAgentA with valid IP address, it will direct to the NetAgentA’s webpage. (List refreshes automatically every 2 minutes)
Page 16
1.2 Individual NetAgentA Info Click on specific NetAgentA , the bottom column shows its hardware , firmware version and MAC address. It also shows the total NetAgentA number that found by Netility and selected Click on NetAgentA Hardware Version Firmware Version...
Page 17
2.1 Launch Web User Interface Select specific NetAgentA from the list and click on Launch Web User Interface to login to the NetAgentA’s webpage Click on Launch Web User Interface Click on NetAgentA Login to the webpage of such NetAgentA...
Page 18
2.2 Network Settings When connecting the NetAgentA for the first time, ensure IP address and other network setting are correctly entered in order to login to the NetAgentA’s webpage via browser or HyperTerminal When select to obtain IP address by DHCP or BOOTP, IP address and other network parameter will be assign by the network ...
Page 19
Default port for each protocol Once password is enabled and configured, it is required to enter the Enter password correct password when change any setting or firmware upgrade...
Page 20
(3) Click on the first NetAgentA from the list, then press and hold on SHIFT key as well as click on the last unit of the NetAgentA =>This is if all NetAgentA from the list are same model ...
Page 21
Here shows the current Netility verison 2.5 Refresh List The list on Netility would refresh every 2 minutes automatically, however, manual refresh is also possible by clicking Refresh List Click on Refresh List Searching List out all the Online NetAgentA...
This page is to show the current UPS connection status in graphic mode with Voltage, Frequency and other information. Information > System Status System Information Here shows all the basic information of the NetAgentA such as hardware / firmware version; Serial Number; Uptime…etc.
Page 23
This page shows UPS information/Battery Information/Rating Information. The data is obtained from the reply of UPS or the settings from [UPS Configuration] webpage Information > System Status Network Status This page shows the network information of NetAgentA.
Information > System Status Wirelss Status This page is to show Wireless connection status and information when NetAgentA communicates via the compatible WiFi dongle Information > Remote Control User can perform several tests to the UPS remotely. Once the option is selected, please...
Information > SMS Modem Status This page shows the Modem status when GPRS modem is connecting with NetAgentA Information > NetFeeler This page shows the environmental status when USB NetFeeler/ NetFeeler II and its accessories are connected with NetAentA.
Page 26
Test log Test UPS Every: Week /2 Weeks/ Month / Quarter UPS can be selected Start Time of UPS Test (hh:mm): To enter the time to begin the test UPS Test Type: Test option can be select from the drop down list UPS Data Log:...
Warning Threshold Values Time out after loss of connection: Send warning alarm when NetAgentA and UPS lost connection at this configured time Critical Load(%): When loading reaches at this % configured, NetAgentA will send warning alarm UPS Temperature (℃):...
Page 28
Remote Shutdown This is to shut down the network server when selected event happens without install shutdown software. Event needs to be adding under UPS Action first and then enter the IP address of server that wish to be shut down by SSH or Telnet with compatible shutdown command of the server system.
Page 29
The settings here override the settings in Weekly Schedule. Warning will be initiated X_ before Schedule shutdown event NetAgentA will send a warning message before a scheduled shutdown. This section sets the delay time period after the message is sent and before the scheduled shutdown is...
This page is to set NetAgentA’s Network settings. IPv4 NetAgentA and DNS IP address can be obtain by drop down list with option of Manually, Using DHCP, or Bootp. If the IP address and DNS has been configured on Netility, then info will automatically show here...
Page 31
IPv6 All NetAgentA series supports IPv6. IP address can be obtain from the drop down list with option of ( Automatic/Stateless DHCPV6/DHCPV6/Manual ) Once click on Apply, NetAgentA will reboot Ethernet Connection Type This section is to set communication speed between NetAgentA and Network.
Page 32
Login Password: Enter the Password you have assigned to your DDNS Account. Use external STUN server to get Public IP to register Choose Yes to ensure that NetAgentA uses the WAN / Public IP to update the selected DDNS server...
Page 33
Ensure NetAgentA is able to connect to Internet. Select icv99.net from the drop down list of the Service Provider. The Domain Name and Login Name will automatically be fill-in with serial number of the device. Enter the password of the NetAgentA which is printed on the NetAgentA label, then click Apply.
Page 34
After 20 minutes, NetAgentA should be login with its DDNS Domain name To change domain name or password, please go to www.icv99.net New Domain name Enter new password Enter email Click on Done...
Page 35
PPPoE Use this option to allow NetAgentA to connect to the Internet directly using your xDSL modem by PPPoE. Enter the Login name and password to enable the connection. Once set-up, NetAgentA will connect directly to the Internet , any abnormal connection failure...
Configuration > Wireless LAN This is to configure NetAgentA Wireless network with compatible USB wireless dongle. Login to the Wireless Router (1)SSID : Name it (any) (2)Authorization:Select WPA2-Personal (3)WPAEncryption:AES (4)WPA-PSKKey:Enter any password (8~63 digits ASCII code) Ensure Wireless>WPS>Enable WPS is...
Page 37
LAN cable is not required WPS Button WPS Setting for the wireless router: When yellow LED of the NetAgentA is flashing , open up WPS setting page of the wireless router. With WPS connection mode, (1)Select ”WPS button” (2)Click on”Start”...
Page 38
Start WPS Connection Process When WPS connection successfully, the yellow LED on NetAgentAA stop flashing...
Page 39
Open up Netility to login to NetAgentA: (1)Once NetAgentA is connected with wireless router via WPS, Netility should be able to find this wireless NetAgentA (2)Login to NetAgentA’s webpage , under Configuration > Wireless Lan webpage, it shows the wireless signal (With distance of 6-10 meters.
Configuration > SNMP This page is to configure NetAgentA SNMP settings to be used by NMS ( Network Management System). (e.g: SNMPView, it is available on the NetAgentA Utility CD.)
Page 41
SNMPv3 Engine ID SNMPv3 Engine ID Format Type: When using SNMPv3, NetAgentA requires to have its Engine ID for identification to generates authentication and encryption key . Format type can be select from the drop down list with option of MAC Address / IPv4 / IPv6 / Manual Once click on Apply, NetAgentA will reboot...
Page 42
Trap Notification Trap Notification Destination IP Address: To set receivers IP address for receiving traps sent by NetAgentA. It is valid for up to 8 IP Addresses. Accept: Select the trap type of its SNMP version or Inform from drop down list. When SNMPv3 trap or SNMPv3 Inform is selected, username/password and authentication information are required.
Page 43
This is to make note for administrator’s reference Events: This is to select events for NetAgentA to send traps. Click on Select to show the full Events List. Click on Test to send test trap to ensure all setting is correct Send Power Restore and Adaptor Restore Traps for X time(s) in X second(s) Interval.
Device Connected This section is to set the usage power and connection status of other devices which connects to the same UPS as NetAgentA uses. Configuration > Email To send email notification when event occurs or data log. Encryption supports are...
Page 45
Test Email Received Email for Event Log (To received email notification To set email addresses to receive warning email sent by NetAgentA when selected event occurs. It is valid for up to 8 Email addresses.
Email for Daily Report (To receive daily report) This section is to set email addresses to receive NetAgentA’s Daily Report at pre-set time. It is valid for up to 4 email addresses. Daily report will be the content of event and data log.
Page 47
SMS Server: If select to use Remote Service to send SMS, then enter the IP address of the SMS Server. (The PC that installed SMS Server Software) : SMS Port If select to use Remote Service to send SMS, enter the port number that SMS Server uses for sending SMS.
Enter specific port number to access or disable for HTTP, HTTP proxy, HTTPS HTTP/HTTPS Account User Name: To set password for NetAgentA Web access. Password: To set password for NetAgentA Web access. Permission: To set No Access / Read/ Read&Write) ...
Page 49
*.*.*.* means any IP address Auto Logoff after Idle for minute (s). ( 0 is disabled) NetAgentA webpage will be logoff automatically if it idles for the preset value. Telnet/SSH Enter specific port number to access or disable for Telnet/SSH...
Page 50
Permission Rule: At least one user account must be Read/Write Permission Rule : User name with Read and Write cannot be blank : IP Filter Only specific IP address could login to NetAgentA *.*.*.* means any IP address...
Page 51
SSL Information NetAgentA supports HTTPS protocol and varies SSL encryptions version for network connection. User may upload its Public Key and Certification for authentication HTTPS Protocols Select the encryption version SSL v2 SSL v3 SSL v1.0 ...
Page 52
RADIUS Server Setting If RADIUS server authentication is required for the network, NetAgentA could be added by entering following parameter. Enable RADIUS in Web/Telnet Login: To select if to enable RADIUS RADIUS Server Address: To enter the IP address of the RADIUS Server Authentication Port:...
NetAgentA supports BACnet/IP (Building Automation and Control/Internet Protocol) BACnet BACNet Device Configure the device ID and access port number for the NetAgentA when using BACnet for communication Notification Enter the IP address of the PC that to be notify by BACnet software when event occurs...
Configuration > SMS Modem When compatible GPRS modem connects with NetAgentA , it is able to send SMS notification when event occurs Modem Setup Procedure 2. Place the SIM card on the holder and insert into GSM Modem 3.
Page 55
SNMS Modem Setting : Modem Communication Port Select “ ttyUSB0” for USB modem connects with NetAgentA directly; SMS Communication: Select between GPRS or CDMA SIM Card PIN: If PIN is required for the SIM card, please enter Confirm SIM PIN:...
NetAgentA to synchronize with external or internal Time Server for correct date and time. System Time : System Time(yyyy/mm/dd hh:mmm:ss) To display the current system time/date of NetAgentA. Or click on Adjust Now to adjust to the correct time/date automatically Time Between Automatic Updates: To set an interval for time synchronization.
Page 57
This page is to set the language interface for NetAgentA. Interface Language To set the language of NetAgentA web pages. When first start login to the webpage of NetAgentA, NetAgentA will auto detects the OS language of the PC and shows the same language on its web pages.
Save/Restore Save Current Configuration Click on Save to save the configuration to your PC. The text file will have a default format of YYYY_MMDD_####.cfg. Administrator permission required. Restore previous configuration Use this function to restore a *.cfg configuration that has been saved earlier. Click Browse…...
Event census Here is to present the event statistically on the selected date Log Information > SMS Log SMS Log It shows SMS record of all mobile number, giving the Date/Time of the SMS sent and a detailed description of each. When reach to the limit, it rewrites on the previous logs. SMS log can be save as csv file .
Log Information > Data Log Data Chart records Input Voltage/Output Voltage/ Frequency/ Loading/Capacity/ Temperature..etc in chart format. Logs can be saved in CSV format by clicking on “Save”. The bar on top can be adjusted to check the log status at specific time of the day. ...
If the NetAgentA is access by WAN IP , Netility Web would also be able to list out all the other available NetAgentA under same LAN as the NetAgentA that has WAN IP. (HTTP port 81 must be enabled on the NetAgentA with WAN IP and domain to be as http://xxx.xxx.xx:81 ( xxx.xx is the WAN IP or domain name)
Page 62
Management > File Manager This is manage log file generates by NetAgentA. Specific log.dat can be download, delete. Once dat. file is deleted, the log record will also be erased on the Log display under Log Information Management > Serial Port Debug It shows the communication status between NetAgentA and UPS by Sent and Received columns.
Page 63
Port Information This is to configure the communication parameter between NetAgentA and UPS. Parameters are Debug Mode; Port; Speed (Baud), Data Bits;Parity and Stop Bits. Two encoding formats: ASCII or Hexadecimal. Management > Help This is to help to illustrate each feature/option that NetAgentA offers ...
Page 64
Default FTP server is set as ftp.icv99.com with its username/password. Click on Update Now, NetAgentA will connects to the FTP server and upgrade to the latest firmware version accordingly. Or, it could upgrade per preset time. To enable NetAgentA’s FTP firmware upgrade, please download the appropriate firmware version from the website and upgrade through FTP Client Software.
Page 65
-FTP login 1. Enter username/password that configured on Netility 2. Enter command Is to show available firmware bin file 3. Enter put command with bin file directory 4. Once complete, enter command quit...
Need help?
Do you have a question about the NetAgentA and is the answer not in the manual?
Questions and answers