KX-TDA200BX All manuals and user guides at all-guides.com CONTENTS Page Page 1 ABOUT LEAD FREE SOLDER (PbF: Pb free) 11.1. INTRUDUCTION 1.1. SUGGESTED PbF SOLDER 11.2. TYPICAL EXAMPLE 1.2. HOW TO RECOGNIZE THAT Pb FREE SOLDER IS 11.3. MPR CARD USED 11.4.
All manuals and user guides at all-guides.com KX-TDA200BX 1 ABOUT LEAD FREE SOLDER (PbF: Pb free) Note: In the information below, Pb, the symbol for lead in the periodic table of elements, will refer to standard solder or solder that contains lead.
KX-TDA200BX All manuals and user guides at all-guides.com 1.2. HOW TO RECOGNIZE THAT Pb FREE SOLDER IS USED Marked PbF (PbF is marked around here) (Component View) PSUP1317ZB RA308 C218 X202 R247 J113 R248 C217 BATALM R243 D407 LED103 CN206...
All manuals and user guides at all-guides.com KX-TDA200BX 3 CAUTION 3.1. NOTE When you note the serial number, write down all of the 11 digits. The serial number may be found on the label affixed to the bottom of the unit.
KX-TDA200BX All manuals and user guides at all-guides.com 4 SPECIFICATIONS 4.1. GENERAL DESCRIPTION Control Bus Original bus (16 bit, 8 MHz,10 megabytes per second) Communication Bus H.100 bus conformity (1024 time slot) Switching Non Blocking Distributed Time Switch Power Input PSU-M 100 V AC to 130 V AC/200 V AC to 240 V AC, 2.5 A/1.4 A, 50 Hz/60 Hz...
All manuals and user guides at all-guides.com KX-TDA200BX 4.3. SYSTEM CAPACITY 4.3.1. Maximum Trunk nd Extension Cards The following number of trunk and extension cards can be installed in the main unit (Hybrid IP-PBX) for expansion. Card Type KX-TDA200 Trunk Card *1...
Blank Slot Cover KX-T30865X Doorphone Available Telephones This main unit (Hybrid IP-PBX) supports all of the Panasonic X-T7xxx and KX-TD7xxx series: · Digital/Analog proprietary telephones (e.g., KX-T7625, KX-T7630, KX-T7633, KX-T7636) · Portable stations (e.g., KX-TD7690, KX-TD7680) · DSS consoles (e.g., KX-T7640) This main unit (Hybrid IP-PBX) does not support the following telephones: ·...
KX-TDA200BX All manuals and user guides at all-guides.com 5.3. SYSTEM CONNECTION DIAGRAM...
Page 11
All manuals and user guides at all-guides.com KX-TDA200BX *Only 1 Server PC can be connected to the main unit (Hybrid IP-PBX). Two or more Server PCs cannot be used simultaneously.
KX-TDA200BX All manuals and user guides at all-guides.com 6 NAME AND LOCATIONS LED Type Color Usage and Status Definition RUN Indicator LED1 Green Display of Power Supply & RUN Status (Power/RUN) OFF: Power OFF (inc. in normal resetting) ON: Power ON & RUN (On-Line) Flash (60/min.): Power ON &...
All manuals and user guides at all-guides.com KX-TDA200BX 7 DISASSEMBLY INSTRUCTIONS 7.1. DISASSEMBLY INSTRUCTION (MPR CARD) 1. Remove the Lib by sliding it in the direction of arrow 1. 2. This will be removed if the user attached a Pad Lock as shown in a Fig.1.
KX-TDA200BX All manuals and user guides at all-guides.com 7.2. DISASSEMBLY INSTRUCTION (BACK BOARD) 1. Remove four Screws (A). 2. Remove the Left Side Cover and the Right Side Cover. 3. Remove the Hook. Remove the Top Cover. 4. Remove nine Screws (B).
Page 15
All manuals and user guides at all-guides.com KX-TDA200BX 6. Remove the RS-232C Connector and LED Connector from Back Board 1. 7. Remove eight Screws (C). 8. Remove Back Board 1. 9. Remove the LED Connector from Back Board 2. 10. Remove the Screw (C).
KX-TDA200BX All manuals and user guides at all-guides.com 8 OUTLINE 8.1. GENERAL DESCRIPTION The control system of the main unit is composed of the main central processing card (MPR card) controlling the entire system and exchanging voice data, the circuit control section (LPR/LC) controlling various telephone lines and the power supply section (POWER).
All manuals and user guides at all-guides.com KX-TDA200BX 8.2. SYSTEM CONTROL 8.2.1. System Control Block Diagram...
Page 18
KX-TDA200BX All manuals and user guides at all-guides.com 8.2.2. Voice (TDM Highway) Bus Block Diagram...
Page 19
All manuals and user guides at all-guides.com KX-TDA200BX 8.2.3. Voice Bus Logical Assignment In the line card, the CT_D line number, which is output in accordance with the inserted slot, and the time slot are assigned by software. For the detail of output slot for each card (optional service card), refer to the service manual of the card (optional service card).
KX-TDA200BX All manuals and user guides at all-guides.com 8.3. BACK BOARD SIGNAL CONNECTION DIAGRAM 8.3.1. CT Bus System Connection Diagram...
Page 21
All manuals and user guides at all-guides.com KX-TDA200BX 8.3.2. EC Bus System Connection Diagram...
Page 22
KX-TDA200BX All manuals and user guides at all-guides.com 8.3.3. System Control and Analog Signal Connection Diagram 8.3.4. Power Supply System Connection Diagram...
All manuals and user guides at all-guides.com KX-TDA200BX 9 MPR CARD CIRCUIT OPERATION 9.1. MPR CARD 9.1.1. Outline 1) Function · System Control · Circuit Switching (includes gain adjustment function) · Conference Call (3 people x 8 ~ 8 people x 3) ·...
Page 24
KX-TDA200BX All manuals and user guides at all-guides.com 9.1.2. Description of Each Part LED (BATALM): Lights when the lithium battery voltage drops below 2.8V. LED (SD ACCES): Lights on when the SD card is being accessed. SD card slot: Mounts the system program SD card.
Page 25
All manuals and user guides at all-guides.com KX-TDA200BX 9.1.3. Block Diagram...
Page 26
KX-TDA200BX All manuals and user guides at all-guides.com 9.1.4. Circuit Description 9.1.4.1. Outline of Block Description · CPU block Operates the main unit control. Also operates various controls, generation of select signal, DMA control and serial port control. This contains the built-in clock function.
Page 27
All manuals and user guides at all-guides.com KX-TDA200BX Signal Name Functions nBAT_ALM Battery Alarm Signal: Indicates the declined voltage of lithium battery. (L: Alarm condition) nBREQ Bus Request: Bus request signal Bus Cycle Start: Bus cycle start signal nCASL Lower Byte Address Column Address Strobe: CAS signal for SDRAM...
Page 28
KX-TDA200BX All manuals and user guides at all-guides.com Signal Name Functions LA[1] -[16] Address bus Lower Byte Select: Indicates Lower byte select signal of SRAM LD[0] -[15] Data Bus LDHW[1] -[0] Down Highway: Data output terminal connected to codec etc. as down data signal of local highway...
Page 29
All manuals and user guides at all-guides.com KX-TDA200BX Functions as the bus master of EC bus (synchronous bus with 16 bit width, transmission rate max.10Mbps). Communicates with ASIC mounted to each option card via EC bus and controls the option card.
KX-TDA200BX All manuals and user guides at all-guides.com clock block power. BAT401, which is a lithium battery for memory backup, is connected to the power supply of IC301, IC302 (SRAM) via D408, D409. IC411 compares BAT401 output voltage to the reference voltage (about 2.8V) and drives LED (BATALM) that indicates dropping of backup voltage.
All manuals and user guides at all-guides.com KX-TDA200BX 11 TROUBLESHOOTING GUIDE 11.1. INTRUDUCTION First, check which part of the system is causing the trouble. Follow the flowchart provided below, and replace each unit in turn with a working unit to identify the damaged unit.
KX-TDA200BX All manuals and user guides at all-guides.com 11.2. TYPICAL EXAMPLE The following items are typical examples when defective occur in main unit. The analysis work first shown in this chapter is done. When you do not correspond to this chapter, or when analysis is not completed, move to the following chapter.
All manuals and user guides at all-guides.com KX-TDA200BX 11.3. MPR CARD 11.3.1. Startup Run indicator (LED201)
Page 34
KX-TDA200BX All manuals and user guides at all-guides.com SD card access light does not flash The battery alarm indication light turns on...
Page 35
All manuals and user guides at all-guides.com KX-TDA200BX ALARM indicator flashes · 1 blink and 1 interval · 2 blinks and 1 interval (1 blink is 0.5 sec. ON and 0.5 sec. OFF. 1 interval is 2 sec.) ALARM indicator flashes ·...
Page 36
KX-TDA200BX All manuals and user guides at all-guides.com Optional service cards cannot start up...
Page 37
All manuals and user guides at all-guides.com KX-TDA200BX 11.3.2. Phone Call The call path cannot connect Noise is created...
Page 38
KX-TDA200BX All manuals and user guides at all-guides.com 11.3.3. Paging No sound (PAGING1) No sound (PAGING2)
Page 39
All manuals and user guides at all-guides.com KX-TDA200BX Noise is Heard (PAGING1) Noise is Heard (PAGING2)
Page 40
KX-TDA200BX All manuals and user guides at all-guides.com Sound is small (PAGING1) Sound is small (PAGING2)
Page 41
All manuals and user guides at all-guides.com KX-TDA200BX 11.3.4. MOH Using No sound is heard (MOH1)
Page 42
KX-TDA200BX All manuals and user guides at all-guides.com No sound is heard (MOH2)
Page 43
All manuals and user guides at all-guides.com KX-TDA200BX Sound is small or loud (MOH1) Sound is small or loud (MOH2)
Page 44
KX-TDA200BX All manuals and user guides at all-guides.com 11.3.5. USB Connection Unable to connect...
Page 45
All manuals and user guides at all-guides.com KX-TDA200BX Connection error occurs...
Page 46
KX-TDA200BX All manuals and user guides at all-guides.com 11.3.6. RS-232C Connection Unable to connect...
Page 47
All manuals and user guides at all-guides.com KX-TDA200BX Connecting speed is slowly...
Page 48
KX-TDA200BX All manuals and user guides at all-guides.com 11.3.7. SD Card I/F Unable to save the system data...
Page 49
All manuals and user guides at all-guides.com KX-TDA200BX 11.3.8. Other The clock data is deleted (unset table)
KX-TDA200BX All manuals and user guides at all-guides.com 11.4. ERROR LOG When a major system error occurs in the main unit (Hybrid IP-PBX), the ALARM indicator on the front of the cabinet turns on red, and the system logs the error information.
Page 51
All manuals and user guides at all-guides.com KX-TDA200BX 11.4.2. List of Errors and Solutions The tables below list the errors and their solutions. When an error whose error code is indicated with "*" occurs in the main unit (Hybrid IP-PBX), the ALARM indicator on the front of the cabinet turns on red, and the system logs the error information.
KX-TDA200BX All manuals and user guides at all-guides.com Error Code Error Message PROBABLE CAUSE SOLUTION PT I/F error · Optional service card malfunction: · See if the corresponding optional service card is installed DHLC, DLC properly · Software error due to external ·...
Page 53
All manuals and user guides at all-guides.com KX-TDA200BX Error Code Error Message PROBABLE CAUSE SOLUTION 022* Not enough free space · Not enough memory space · Delete the files whose file names start with "$" from SD available to save the system data,...
Page 54
KX-TDA200BX All manuals and user guides at all-guides.com Error Code Error Message PROBABLE CAUSE SOLUTION LPR alive check error · Optional service card malfunction: · See if the corresponding optional service card is installed DHLC, DLC, CSIF, T1, PRI, OPB3,...
All manuals and user guides at all-guides.com KX-TDA200BX 12 DIAGNOSIS 12.1. DIAGNOSIS FEATURES Card Test and Pair Port Test is in Diagnosis Features. 12.1.1. Card Test Card Test -SUMMARY Description Diagnose all kind of Cards. Parallel of Diagnose item of Card Tests and every Cards...
KX-TDA200BX All manuals and user guides at all-guides.com 12.1.1.2. Card CT Bus Diagnosis Diagnose CT bus by Loop back test to use CT bus DHLC SLC8/L MSLC/ CS-INF LCOT OPB3 E&M CTI- SLC8 SLC16 LINK Object of Card Diagnosis result...
All manuals and user guides at all-guides.com KX-TDA200BX 12.1.1.6. DSP DTMF Receiver Diagnosis Diagnose DTMF receiver of DSP in the Card to use DTMF generator of DSP DHLC SLC8/L MSLC/ CS-INF LCOT OPB3 E&M CTI- SLC8 SLC16 LINK Object of Card...
Page 58
KX-TDA200BX All manuals and user guides at all-guides.com 12.1.1.10. Super Frame Synchronization Diagnosis Diagnose Super frame synchronization feature of CS-INF DHLC SLC8/L MSLC/ CS-INF LCOT OPB3 E&M CTI- SLC8 SLC16 LINK Object of Card Diagnosis point DECT DECT super frame synchronization test...
KX-TDA200BX All manuals and user guides at all-guides.com 13 IC DATA 13.1. Pin No. Pin Name Description Clock mode setting Clock mode setting Vcc-TRC*1 Power for RTC XTAL2 Crystal oscillator terminal for built-in RTC EXTAL2 Crystal oscillator terminal for built-in RTC (*6)
Page 65
All manuals and user guides at all-guides.com KX-TDA200BX Pin No. Pin Name Description Power supply (*3) Power supply (*3) D18/PTA[2] Data bus/I/O port A D17/PTA[1] Data bus/I/O port A D16/PTA[0] Data bus/I/O port A VssQ Power for I/O (0V) Data bus VccQ Power for I/O (3.3V)
Page 66
KX-TDA200BX All manuals and user guides at all-guides.com Pin No. Pin Name Description WE3/DQMUU/ICIOW O/I/O D31-D24 select signal/DOM (SDRAM) /PCMCIA I/O write/I/O port K R/PTK[7] RD/WR Read/Write AUDSYNC/PTE[7] O/I/O AUD synchronization/I/O port E VssQ Power for I/O (0V) CS0/MCS[0] Chip select 0/mask ROM chip select 0 VccQ Power for I/O (3.3V)
Page 67
All manuals and user guides at all-guides.com KX-TDA200BX Pin No. Pin Name Description Power supply (*3) XTAL Clock oscillator terminal EXTAL External clock/crystal oscillator terminal STATUS0/PTJ[6] O/I/O Processor status STATUS0/PTJ[7] O/I/O Processor status TCLK/PTH[7] Clock I/O for TMU or RTC/I/O port J...
All manuals and user guides at all-guides.com KX-TDA200BX 15 HOW TO REPLACE A FLAT PACKAGE IC 15.1. PREPARATION 15.3. REMOVING SOLDER FROM BETWEEN PINS · PbF (: Pb free) Solder · Soldering Iron 1. Add a small amount of solder to the bridged pins.
All manuals and user guides at all-guides.com KX-TDA200BX 18 REPLACEMENT PARTS LIST Note: Ref. Part No. Part Name & Description Remarks 1. RTL (Retention Time Limited) PSMH1205Z CHASSIS, LED The marking (RTL) indicates that the Retention Time is PSHD1091Z BOLT WITH NUT limited for this item.
KX-TDA200BX All manuals and user guides at all-guides.com Ref. Part No. Part Name & Description Remarks 18.3. MPR CARD PARTS D409 MA728 DIODE(SI) Ref. Part No. Part Name & Description Remarks DA401 MA143 DIODE(SI) PCB1 PSWP1DA100BX MPR CARD ASS´Y (RTL)
Page 75
All manuals and user guides at all-guides.com KX-TDA200BX Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks RA306 D1HA1038A005 RESISTOR ARRAY C174 ECUV1C104ZFV RA307 D1HA1038A005 RESISTOR ARRAY RA308 D1HA1038A005 RESISTOR ARRAY C201 ECUV1H220JCV...
Page 76
KX-TDA200BX All manuals and user guides at all-guides.com Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks R137 ERJ3GEYJ103 C430 ECUV1H153KBV 0.015 R138 ERJ3GEYJ103 C431 ECUV1H153KBV 0.015 R139 ERJ3GEYJ103 C433 ECUV1C104ZFV C435 ECUV1A105ZFV...
Page 77
All manuals and user guides at all-guides.com KX-TDA200BX Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks R241 ERJ3GEYJ473 R455 ERJ3GEYJ223 R242 ERJ3GEYJ473 R456 ERJ3GEYJ223 R243 ERJ3GEYJ104 100k R457 ERJ3GEYJ223 R244 ERJ3GEYJ472 4.7k...
Page 78
KX-TDA200BX All manuals and user guides at all-guides.com Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks J115 PQ4R18XJ000 L115 ERJ3GEY0R00 J116 PQ4R18XJ000 L116 ERJ3GEY0R00 J121 ERJ3GEY0R00 L117 ERJ3GEY0R00 J123 ERJ3GEY0R00 L118 ERJ3GEY0R00...
All manuals and user guides at all-guides.com KX-TDA200BX Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks L186 PFVF1A471SG CERAMIC FILTER X101 PSVCC0025GT CRYSTAL OSCILLATOR L187 PFVF1A471SG CERAMIC FILTER X102 PSVCC0019CT CRYSTAL OSCILLATOR...
All manuals and user guides at all-guides.com KX-TDA200BX 19 FOR THE SCHEMATIC DIAGRAM Note: 1. DC voltage measurements are taken with an oscilloscope or a tester with a ground. 2. The schematic diagrams and circuit board may be modified at any time with the development of new technology.