Vision Fitness E4000 Assembly Manual page 3

A s s e m b l y
G u i d e
E4000
DUAL-ACTION UPRIGHT FITNESS BIKES
To avoid possible damage to this Fitness Bike, please follow these assembly steps in the correct order.
Before proceeding, find your new Fitness Bike's serial number located on the front axle tube, and enter
here:
Refer to this number when calling for service, and enter this serial number on your Warranty Card and in
your own records. Be sure to read your Owner's Guide before using your new Fitness Bike.
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12
NOTE:
It is recommended that you apply grease to the threads of each screw as you assemble your Fitness
Bike to prevent loosening and noise. Also, during each assembly step, ensure that ALL screws and nuts
are in place and partially threaded in before completely tightening any ONE screw.
1 ORANGE BAG
STEP
• Slide the rear foot in place and
secure with four bolts (M8x20L).
Tighten with the 5mm T-shaped wrench.
2 BLUE BAG
STEP
• Loosen the set screw in the arm axle
with the 4mm L-shaped Wrench.
• Slide the front arm axle into the plastic
sleeve of the front foot. Slide a wavy
washer onto each end of the axle.
• You will now need to disassemble
part of the roller assembly on the arm
crank. Please remove the nylock nut
(M8), the washer (M8x17), the
tension spring, the washer (M13),
and the outside roller. Repeat this step
on the left side.
• Slide the right dual-action arm onto
the right arm axle and the right inside
roller. Reinstall the outside roller, the
washer (M13), the tension spring, the
washer (M8x17), and the nylock nut
(M13). Repeat this step on the left
side
• Attach the right arm cover to the
right arm. It should snap into place.
Repeat this step on the left side.
• Install the right transport wheel, the
washer (M8x30), and the nylock nut
(M8) to each end of the axle. Tighten
with the closed wrench. Repeat this
step on the left side.
• Tighten the set screw in the arm axle
4
STEP
5
STEP
1
STEP
Tension
Control Knob
Water Bottle
Cage
Upper
Cover
3
STEP
2
Left
STEP
Dual-Action Arm
Inside Roller
Right
Dual-Action Arm
Outside
Roller
Front Arm
Right Arm
Axle
Cover
Transport
Wheel
3 PINK BAG
STEP
• Remove the three screws from the
upper cover of the bike frame.
• Slide the upper cover onto the
console mast.
• Attach the included wire tie to the
sensor wire and pull the sensor wire
up through the console mast. Slide the
tension control cable up through the
console mast.
• Slide the console mast onto the
frame bracket and fix it in place with
two bolts (M8x40L) and the 5mm
T-shaped wrench.
• Install the batteries into the console.
Plug the sensor wire into the console.
Attach the console with the included
screws.
• Turn the tension knob to Level 15.
Connect the tension control cable
from the knob to the cable inside the
mast. Turn the knob to Level 1 and
mount the knob to the mast with the
screw (M5 x 12L).
• Slide the upper cover into place
and secure it to the frame using the
two screws for the front and one
screw for the back of the cover
(these are the screws you removed
earlier in step 3).
• Attach the water bottle cage to the
upper cover with included screws.
4 SEAT
STEP
• Place the seat on the seat post and
tighten the nuts on the underside of the
seat with the closed wrench.
BLACK BAG
5
STEP
• Attach the left and right pedals to
the left and right crank arms. Tighten
using the 15mm Pedal wrench.
• Slide the foam grips onto the dual-
action arms. NOTE: If they are difficult
to slide on, try to spray a lubricant
such as Armor-All onto the arm to help
with this step.