Leviton Acenti ACP10 Installation Instructions

Incandescent: 800W-6.67A @ 120V
DI-000-ACP10-00A-X0
WARNINGS AND CAUTIONS:
• To be installed and/or used in accordance with appropriate electrical codes and regulations.
• If you are unsure about any part of these instructions, consult a qualified electrician.
• Controlling a load in excess of the specified ratings will damage the unit and pose risk of fire, electric shock, personal injury or death.
Check your load ratings to determine suitability for your application.
• Do not install this unit to control a receptacle.
Tools needed to install your Sensor:
Slotted/Phillips Screwdriver Electrical Tape
Pliers Pencil
Cutters Ruler
INSTALLING YOUR SENSOR
√
NOTE: Use check boxes when Steps are completed.
WARNING:
TO AVOID FIRE, SHOCK, OR DEATH;
Step 1
TURN OFF POWER at circuit breaker or fuse and test
that power is off before wiring!
OFF ON OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON OFF ON
OFF ON OFF ON
OFF ON OFF ON
Identifying your wiring application (most
Step 2
common):
NOTE: If the wiring in the wall box does not resemble
this configuration, consult a qualified electrician.
Single-Pole
2
1
1. Line (Hot)
2. Neutral
3. Ground
3
4. Load
4
Wall Switch Passive Infrared Occupancy Sensor
Fluorescent: 1200VA-10A @ 120V 2700VA-10A @ 277V
Compatible with incandescent lamps, electronic and magnetic low voltage ballasts, electronic and magnetic ballasts, and fans
INSTALLATION INSTRUCTIONS
Preparing and connecting wires:
Step 3
Cut
(if necessary)
Strip Gage
(measure bare wire here)
• Pull off pre-cut insulation from dimmer leads.
• Make sure that the ends of the wires from the wall box are
straight (cut if necessary).
• Remove insulation from each wire in the wall box as shown.
For non-standard wiring applications, refer
to Wire Nut and Conductor Size Chart
WIRE NUT / # OF COND.
COMBINATION CHART
1- #12 w/ 1 to 3 #14, #16 or #18
2- #12 w/ 1 or 2 #16 or #18
1- #14 w/ 1 to 4 #16 or #18
2- #14 w/ 1 to 3 #16 or #18
Installing your Sensor –
Step 4
Single-Pole Wiring Application:
Black
1
Green
3
4
Blue
Ground wire must connected for unit to operate.
Allow 1 minute for warmup after connected.
Cat. No. ACP1Ø
No Minimum Load Required
WARNINGS AND CAUTIONS:
• The Cat. No. ACP10 Occupancy Sensor is intended to replace a standard light switch.
• Do not touch the surface of the lens. Clean outer surface with a damp cloth only.
• Disconnect power at circuit breaker or fuse when servicing, installing or removing fixture.
• Use this device only with copper or copper clad wire. With aluminum wire use only devices marked CO/ALR or CU/AL.
Step 4 cont'd
Hot (Black)
5/8"
(1.6 cm)
Line
120/277VAC, 60Hz
Neutral (White)
WIRING SENSOR:
Connect wires per WIRING DIAGRAM as follows:
• Green or bare copper wire in wall box to Green dimmer lead.
NOTE: Ground wire must be connected for unit to operate. Allow 1
minute for warmup after connected.
• Line Hot wall box wire to Black sensor lead.
• Load wall box wire to Blue sensor lead.
Testing your Sensor prior to completely
Step 5
mounting in wall box:
2
controls can be accessed by removing the wallplate (if applicable) and
control panel cover (refer to Sensor Features Diagram). Use a small
straight blade screwdriver to adjust knobs and a finger to adjust the
blinder levers.
NOTE: DO NOT press in on blinder levers or use excessive force
(refer to Sensor Features Diagram).
• Attach the Control Panel cover.
If lights still do not turn ON, refer to the TROUBLESHOOTING
section.
Supplemental: 1/4hp-5.8A @ 120V
.
Sensor
Step 5 cont'd
BLINDERS: The blinders can narrow the field-of-view of the device
Blue
to prevent unwanted activation from traffic in adjacent space. There
Black
are two blinders, and each operate independently. To operate the
blinders, use a finger or small screwdriver to move the blinder
Black
Load adjustment levers toward or away from the center of the device.
The blinder levers are found above the control knobs and below the
Green
White text 'BLINDERS' on the control panel. With both levers moved fully
Ground
towards the center, the field-of-view is narrowed to 32°. With both
levers moved fully away from the center, the field-of-view is at a
maximum 180° (refer to Sensor Features Diagram).
TIME-DELAY: Cat. No. ACP1Ø will turn lights ON when motion is
detected. When motion is no longer detected, the Sensor Unit will
wait a certain amount of time and then turn the lights OFF. This wait
time is called 'time-out'.
The "time-out" is selected from four (4) preset values. Pointing the
arrow at one of the markings on the face chooses the value of time.
The following selections are available:
Face Marking
(/) Slash Mark
walk-test.
• Restore power at circuit breaker or fuse.
1
• Carefully holding device as shown,
2
allow approximately thirty (30)
3
seconds after power is supplied for
The "time-out" is factory preset to ten (10) minutes. Refer to
warm-up. After this, the device will
Sensor Features Diagram.
turn the lights ON and the LED will blink.
NOTE: All time durations mentioned in the instructions are
• Perform the adjustments for the
approximate within 10 seconds.
time-out and the light setting (refer
to Time Delay and Ambient Light
sections).
If necessary, adjust the range
control and the blinders to stop any
unwanted activation of the lights.
NOTE: To avoid PERMANENT
DAMAGE to the unit, be careful NOT TO
OVERTURN the control knobs or levers
when setting the Cat. No. ACP1Ø. The
Control Panel Cover
Value of Time
30 second fixed time-out used for performing a
10 minute time-out
20 minute time-out
30 minute time-out
Sensor Features Diagram
Blinder
Adjustment
Levers
1 2 4 7 4 7
3 10
10
Time Range Light
Slash Mark