Download Print this page
Ranger R30XLT Installation And Operation Manual

Ranger R30XLT Installation And Operation Manual

Automobile and light truck single piece wheel tire changer
Hide thumbs Also See for R30XLT:

Advertisement

Quick Links

INSTALLATION AND OPERATION MANUAL
AUTOMOBILE AND LIGHT TRUCK
SINGLE PIECE WHEEL
TIRE CHANGER
MODEL:
R30XLT
RECEIVING
The shipment should be thoroughly inspected as soon as it
is received. The signed Bill of Lading is acknowledgement
by the shipping carrier as receipt of this product as listed
in your invoice as being in a good condition of shipment. If
any of these goods listed on this Bill of Lading are missing
or damaged, do not accept goods until the shipping carrier
makes a notation on the freight bill of the missing or dam-
aged goods. Do this for your own protection.
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
PLEASE READ THE ENTIRE CONTENTS OF THIS MANUAL PRIOR TO
INSTALLATION AND OPERATION. BY PROCEEDING WITH TIRE CHANGER
INSTALLATION AND OPERATION YOU AGREE THAT YOU FULLY
UNDERSTAND AND COMPREHEND THE FULL CONTENTS OF THIS MANUAL.
FORWARD THIS MANUAL TO ALL OPERATORS. FAILURE TO OPER-
ATE THIS EQUIPMENT AS DIRECTED MAY CAUSE INJURY OR DEATH.
BE SAFE
Your new tire changer was designed and built with safety
in mind. However, your overall safety can be increased with
proper training and thoughtful operation on the part of the
operator. DO NOT operate or repair this equipment without
reading this manual and the important safety instructions
shown inside. Keep this operation manual near the tire
changer at all times. Make sure that ALL USERS read and
understand this manual.
1
MAN REV B 04-20-11
P/N 5900380
1645 Lemonwood Dr.
Santa Paula, CA. 93060, USA
Toll Free 1-800-253-2363
Tel: 1-805-933-9970
Fax: 1-805-933-9160
www.bendpak.com

Advertisement

loading
Need help?

Need help?

Do you have a question about the R30XLT and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Ranger R30XLT

  • Page 1 INSTALLATION AND OPERATION MANUAL AUTOMOBILE AND LIGHT TRUCK SINGLE PIECE WHEEL TIRE CHANGER MODEL: R30XLT RECEIVING BE SAFE The shipment should be thoroughly inspected as soon as it Your new tire changer was designed and built with safety is received. The signed Bill of Lading is acknowledgement in mind.
  • Page 2 Chassis Weldment Power Cord Grip Chassis Side Cover Power Cord Foot Pedal Hood STS M5.5 x 1.0 x 25 PHPS M6 x 1.0 x 20 SHCS M5 x 0.8 x 20 Chassis Front Board Washer Ø5 Hex Nut M8 x 1.25 Soap Brush Pedal Divider Soap Bucket...
  • Page 3 B-P3181988 COMPLETE VALVE ASSEMBLY 148-1 148-13 148-2 148-14 148-3 PHPS M6 x 1.0 x 16 148-15 Nut M8 x 1.25 148-4 Pedal / Valve Bracket Weldment 148-16 Pedal Valve Link USE B-P3181988 B-P3181976 148-5 148-17 Pedal Spring USE B-P3181988 148-5-1 148-18 Cotter pin USE B-P3181988...
  • Page 4 Quick Change Chuck Assy Swing Arm Unit Weldment 242-1 Tower unit weldment Hex Shaft Locking Plate Coiled Air Hose Ø8mm (9ft) Assist Tower Tool Holder Locking Handle Cover Air Chuck Washer Ø12 Locking Handle 244-1 Bolt M12 x 1.75 x 80 Vertical Shaft Locknut M16 x 2.0 Hex Shaft Spring...
  • Page 6 Snap Ring Ø35 PU Air Compressor Hose Ø6mm Clout Assist Tower Rear Cylinder Plate Assist Tower Quick Chuck, Outer O-ring Ø85 x 3.6mm Assist Tower Quick Chuck, Inner Cylinder Body Ø75 x 360mm Tray lever Assist Tower Pivot Pin Straight Pin Ø10 x 45 Gland Plastic Disk SHCS M10 x 1.5 x 25...
  • Page 7 Turntable Assembly 302-17 Wiper Seal 32 x 20 x 6 Large Cylinder Cover Turntable Ø750 302-18 Cylinder Wear Ring Jaw Clamp Inner Adjustment Pin B-P 5327621 Jaw Clamp Cylinder Assem- 302-19 O-ring 25 x 3.1 B-P5327622 Clamp Pin Spring Slide Block Unit Weldment Fitting B-P3182010 PIN B-P5327623 302-1...
  • Page 8 BEAD BREAKING SEAL KIT B-P5327772 Bead Breaker Cylinder Assy Snap Ring Ø16 Brass 90° Fitting ¼ NPT x 10mm BB Blade Adjustment Rod Large Cylinder Tube Locknut M16 x 2.0 Thin Nut M18 x 2.5 x 1.5 Wave Washer Ø16 Piston Spacer Washer Ø16 Wiper Seal Ø200 x 12 x 6mm SEE KIT BELOW...
  • Page 9 Reduction Box Assembly Large Belt Pulley O-ring Ø60 x 2.65 Rotary Joint Block B-P3182006 Rotary Joint Collar, See 500-1 500-1 Oil Seal Ø45 x 25 x 10 Gearbox Top Flange Gearbox Bottom Flange Electrical Line Hex Bolt M10 x 1.5 x 200 Nut M10 x 1.5 Power Lline Oil Plug...
  • Page 11 B-P5325731 Cotter Pin Ø3 x 25 Air Valve Spool Washer M6 x 12mm Flat Directional Switch Bracket Washer M6 Flat Locknut M6 x 1.0 PHPS M6 x 1.0 x 12 Foot Pedal Rubber Insert PHPS M4 x 0.7 x 10 Foot Pedal (Left) Nut, spool B-P3000606 Foot Pedal Limit Rod...