Table of Contents
Related Manuals for Becker B-Tronic VarioControl VC3201B
Summary of Contents for Becker B-Tronic VarioControl VC3201B
- Page 1 B-Tronic VarioControl VC3201B Assembly and Operating Instructions Transmitter, 1-channel, bidirectional 4035 630 130 0a 29/05/2017 Becker-Antriebe GmbH Friedrich-Ebert-Straße 2-4 35764 Sinn/Germany www.becker-antriebe.com...
-
Page 2: Table Of Contents
Table of contents General ...................... 4 Warranty ...................... 5 Safety instructions .................... 6 Intended use ...................... 8 Explanation of displays and buttons .............. 10 Wiring ...................... 12 Programming transmitters in a B-Tronic device or KNX RF compatible device from an- other manufacturer ................... - Page 3 Simplified EU declaration of conformity............... 23...
-
Page 4: General
General You can operate drives and control units with bidirectional KNX radio with this trans- mitter. This device is exceptionally easy to use. Please observe these Assembly and Operating Instructions when installing and set- ting up the equipment. Explanation of pictograms CAUTION indicates a hazardous situation CAUTION which, if not avoided, could result in injury. -
Page 5: Warranty
Denotes user tips and other useful informa- tion. You will find the current status on the type plate according to the following symbol: The description of the acknowledgement can be found in the relevant instructions for the receiver. Warranty Structural modifications and incorrect installation which are not in accordance with these and our other instructions can result in serious injuries, e.g., crushing of limbs. -
Page 6: Safety Instructions
The end product manufacturer and fitter have to ensure that all the relevant current statutory, official and, in particular, EMC regulations are adhered to during utilisation of our products, especially with regard to end product manufacture, installation and customer advice. Safety instructions General information Important information for:... - Page 7 • Observe all pertinent country-specific regulations. • Dispose of exhausted batteries properly. Only replace batteries with the identical type (see Technical data). Caution • Keep people out of the system’s range of travel. • If the system is controlled by one or more transmitters, the sys- tem’s range of travel must always be visible during operation.
-
Page 8: Intended Use
Intended use The transmitter described in these instructions may only be used for operating suit- able drives and control units with bidirectional KNX radio. You can operate either one group or a number of groups of devices with this transmitter. •... - Page 9 • Ensure that the control unit is not installed or operated close to metal surfaces or magnetic fields. • Radio-controlled systems transmitting on the same frequency may cause reception interference. • Note that the range of the radio signal is limited by legislation as well as by design.
-
Page 10: Explanation Of Displays And Buttons
Explanation of displays and buttons VC3201B 4035 200 033 0 1. Antenna... - Page 11 2. Function selection switch Position P Drive Position I ON/OFF Position F Standard Position R Dimmer 3. Reference potential of button inputs P1 and P2 4. Battery protective strip 5. Button input P2 6. Button input P1 7. LED...
-
Page 12: Wiring
Wiring Ensure that there is optimal radio reception. Drive / dimmer connection with a 2-way changeover switch (no 2-way changeover switch for roller shutters) The assignment of the wires P1 and P2 according to the direction of travel is dependant on how the drive is installed (mounted to the right or to the left). - Page 13 VC3201B 4035 200 033 0...
- Page 14 ON/OFF control unit connection (e.g., lighting) with a 1-way changeover switch VC3201B 4035 200 033 0...
-
Page 15: Programming Transmitters In A B-Tronic Device Or Knx Rf Compatible Device From Another Manufacturer
Programming transmitters in a B-Tronic device or KNX RF compatible device from another manufacturer Put the receiver into programming mode. Please find the appropriate description in the instructions for the receiver. Set the function selection switch to the required position (P = drive, I = ON/OFF, R = dimmer). -
Page 16: Use In System Network
Use in system network You cannot make any settings (e.g., limit positions, etc.) to B-Tronic devices using this transmitter. The transmitter can only be used for operation. Operating drives For the desired direction, press the relevant button on the operator unit for about 1 second. -
Page 17: Operating Dimmers
Operating dimmers Press any button on the operator unit for about 1 second to switch the lights on. The assignment of the buttons A and B depends on how the wires P1 and P2 are connected to the operator unit. Button A for switching on and dimming Button B for switching off and dimming brighter... - Page 18 Switching on Press button A for about 1 second. Dimming brighter Press button A until the desired brightness value is reached. Dimming darker Press button B until the desired brightness value is reached. Switching off Briefly press button B.
-
Page 19: Clearing Transmitters From A B-Tronic Device Or Knx Rf Compatible Device From Another Manufacturer
Clearing transmitters from a B-Tronic device or KNX RF compatible device from another manufacturer Put the receiver into programming mode. Please find the appropriate description in the instructions for the receiver. Set the function selection switch to the required position (P = drive, I = ON/OFF, R = dimmer). -
Page 20: Changing Batteries
Changing batteries You will find the appropriate battery type in the "Technical data" chapter. Open the cover of the battery com- partment. Carefully remove the PCB from the housing. Take out the batteries. Insert the new batteries correctly. Carefully place the PCB back into the housing. -
Page 21: Technical Data
Technical data Rated voltage 3 V DC Battery type CR 2025 Degree of protection IP 20 Permissible ambient temperature 0°C to +45°C Radio frequency 868.3 MHz The maximum transmitter range on and in the building is up to 25 m and in the open up to 350 m. -
Page 22: What To Do If
What to do if...? Problem Remedy Receiver does not react, Insert a new batteries. status LED remains off. Insert the batteries correctly. Remove the battery protective strip. Reduce the distance to the receiver. Program transmitter. Check the receiver. Set the function selection switch to position "F". Programme the receiver with the function selection switch in the right position. - Page 23 Simplified EU declaration of conformity Becker-Antriebe GmbH hereby declares that this radio control system complies with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following web ad- dress: www.becker-antriebe.com/ce Subject to technical changes without notice.
Need help?
Do you have a question about the B-Tronic VarioControl VC3201B and is the answer not in the manual?
Questions and answers