Analog black & white ccd camera tv format (with and without nd filter) (30 pages)
Summary of Contents for Primetech PXA30SHP
Page 1
PRIMETECH ENGINEERING RoHS Operation Manual Ver. 1.1 VGA CCD Black & White Camera Model PXA30SHP Primetech Engineering Corp. 1/36...
Page 2
PRIMETECH ENGINEERING Thank you for your purchase of the Primetech Engineering product. We ensure that you will enjoy this and other products from Primetech Engineering for many years. Keep this manual and warranty card handy for future reference. To ensure the safe use of this product, carefully read the warnings and cautions provided below prior to use: Warning Failure to follow the warning message may result in death or serious injury.
Page 3
PRIMETECH ENGINEERING Primetech Engineering shall assume no responsibility for the following under any circumstance: ■ Loss arising from fire, earthquake, a man-made disaster or an act of God; willful or accidental misuse of the product; or use of the product by a third party in an abnormal manner;...
Page 4
PRIMETECH ENGINEERING Revision History Revision Date of revision Description of change 2019/03/14 Released the initial version. 2020/07/15 Correction of errors 4/36...
PRIMETECH ENGINEERING 1. Overview This operation manual describes functions and procedures for the industrial analog camera (B/W). 1.1. Characteristics • Diverse mode setting The following settings can be used by toggling the switch on the rear panel. • Synchronous input/output •...
PRIMETECH ENGINEERING 4. Specifications of Camera Parts 4.1. Front/Top/Bottom [1] Lens mount (C-mount) [2] Auxiliary screw hole for fixing camera (top) [3] Auxiliary screw holes for fixing camera/ screw holes for installing tripod (bottom) [4] Reference screws hole for fixing...
PRIMETECH ENGINEERING 4.2. Rear panel [2] DIP switch for setting shutter speed and mode [1] VIDEO OUT/DC IN/SYNC (video output/DC power/ sync signal input/output) terminal (12-pin connector) [5] 75Ω termination switch [3] VD/HD signal input/output switch [4] Manual gain control knob Caution Turn off the module before setting switches.
Page 11
PRIMETECH ENGINEERING [5] 75 termination switch Set the switch to ON for termination. The factory setting is OFF. 11/36...
PRIMETECH ENGINEERING 4.3. Pin assignment for VIDEO OUT/DC IN/SYNC (video output/DC power/synchronizing signal input/output) terminal Rear panel Pin assignment for VIDEO OUT/DC IN/SYNC (Video output/DC power/synchronizing signal input/output) terminal Pin No. Camera synchronizing External synchronizing Restart/reset Externally triggered signal output...
PRIMETECH ENGINEERING 4.4. Input phase specifications for external VD/HD signal External VD (Falling) External VD (Rising) External HD Units: Clock 1 clk = 33.333 nsec / 66.666nsec (60fps) (30fps) Set the phase relationship for external VD and HD signals as shown in the above figure.
PRIMETECH ENGINEERING 4.6. Trigger pulse specifications 4 to 5.0 V 2 μs to 1/4 s 0 to 1.0 V • Input impedance: 10 k or more • Input the pulse width between 100 s and 1/4 s for DIP switch setting.
PRIMETECH ENGINEERING 5. Shutter Speed Setting 1/125 1/250 1/500 1/1000 1/2000 1/4000 1/10000 1/20000 1/100 unit:sec ※Shutter speed is at 60fps. Shutter speed will be twice at 30fps. ※Non-reset mode/reset mode is set, shutter OFF will be pulse width trigger shutter.
PRIMETECH ENGINEERING 6. Trigger Mode Setting Nomal Restart Reset shutter reset reset mode mode mode mode 6.1. Normal Shutter Mode Each scan modes are available. In addition, input and output of VD / HD signals. 6.2. Restart Reset Mode By inputting restart/reset signals (VD/HD) from an external device, you can obtain information for one screen at an arbitrary timing.
PRIMETECH ENGINEERING 6.3. External Triggered Shutter Mode Inputting a trigger from an external device will enable capturing of high-speed moving objects at a correct position. When the trigger pulse width is set to 1/3 s or more, the output is switched to a normal video signal.
PRIMETECH ENGINEERING 7.3. High-rate Scanning Mode You can increase the frame rate by setting the high-rate scanning mode. Signal output from the video output terminal is the center of the screen. Area where image is not output Video Effective Area...
PRIMETECH ENGINEERING 9.2. Binning Readout Timing Chart The horizontal timing chart at 60 fps setting is shown below. clk:30MHz at 60fps (33.33nsec) (33.00μs) (2.33μs) Video output Signal(Typ) Effective pixel (3.73μs) (4.10μs) (3.17μs) (11.00μs) (22.00μs) Output video period Horizontal blanking ※A unitless number represents the number of clock counts.
PRIMETECH ENGINEERING 9.3. 1/2 High-rate Scanning Readout Timing Chart. The horizontal timing chart at 60 fps setting is shown below. clk:30MHz at 60fps (33.33nsec) (33.00μs) (2.33μs) Video Output Signal(Typ) Effective pixel (3.73μs) (4.10μs) (3.17μs) (11.00μs) (22.00μs) Horizontal Output video period blanking ※A unitless number represents the number of clock counts.
PRIMETECH ENGINEERING 9.4. 1/4 High-Rate scanning Readout Timing Chart. The horizontal timing chart at 60 fps setting is shown below. clk:30MHz at 60fps (33.33nsec) (33.00μs) (2.33μs) Video Output Signal(Typ) Effective pixel (3.73μs) (4.10μs) (3.17μs) (11.00μs) (22.00μs) Horizontal Output video period blanking ※A unitless number represents the number of clock counts.
Page 36
Thus we assume no responsibility whatsoever for any violation resulting from such use. Contact: Contact: Primetech Engineering Corp. Primetech Engineering Corp. 1-3-25, Koishikawa, Bunkyo-ku, 1-3-25, Koishikawa, Bunkyo-ku,...