Advertisement
Quick Links
KB100, KB110 and KB200 REPLACEMENT STRAP
INSTRUCTIONS
P/N 885-KIT
KB100
KB110
KB200
Hardware Supplied
Two 5/8" Phillips Pan Head Machine Screws One Truss Head Wood Screw
Tools Required:
Phillips Head Screwdriver or 1/8" Allen Wrench
1. Open Baby Changing Station. Remove the
screws that secure the old strap to the unit.
Discard old strap and screws.
2. Position the new strap on the unit with the
buckle towards the liner dispenser. (See Image).
3. For all models, take one of the Phillips Pan
Head Machine Screws. Insert it through the hole
in the chafe tab and into the hole in the front of
the bed. Secure the screw into the screw insert.
4. Repeat step 3 for the other end of the strap.
For KB200 model use the other Phillips Pan Head
Machine Screw. For KB100 and KB110 models
use the Truss Head Wood Screw.
5. Ensure that the strap is buckled. Clean up
mess and close unit.
®
Koala Kare Products ǁ 6982 S Quentin St. ǁ Centennial, CO 80112
Toll Free: 888.733.3456 ǁ 303.539.8300 ǁ Fax: 303.539.8399
www.koalabear.com
P/N 496 January 2011
Advertisement
Related Manuals for Koala Kare 885-KIT
Summary of Contents for Koala Kare 885-KIT
- Page 1 Truss Head Wood Screw. 5. Ensure that the strap is buckled. Clean up mess and close unit. ® Koala Kare Products ǁ 6982 S Quentin St. ǁ Centennial, CO 80112 Toll Free: 888.733.3456 ǁ 303.539.8300 ǁ Fax: 303.539.8399 www.koalabear.com P/N 496 January 2011...
- Page 2 KB200 REPLACEMENT SHOCK INSTRUCTIONS P/N 472-KIT Materials Supplied: Materials Needed: Shock Flat Head Screwdriver 1. Unlock the liner dispenser with the key (included) and remove the four screws securing the liner dispenser to the frame. Remove plastic liner dispenser from wall. 2. There should be six screws holding the metal mounting frame to the wall. Remove the four lower mounting screws. Keep all of these screws to remount the unit. 3. Loosen the upper two mounting screws, but do not remove them. You should be able to lift the unit off the upper mounting screws using the keyhole slots. 4. Once the unit is removed from the wall, allow the unit to close and lay it flat on a non-abrasive table or countertop with the frame side facing up. 5. Using a flat head screwdriver, release the “C” clip (which holds “C” Clip the bottom of the shock to the ball stud) by sliding the screwdriver between the “C” clip and the head of the shock. Once released pull the head of the shock off the ball stud. Repeat this for the other end of the shock. Screwdriver 6. Take the new shock and attach the thin end to the ball stud closest to the bed of the unit by pushing it until you hear it click into place. Twist the head back and forth to ensure it is secure. 7. Take the other end of the shock in one hand and the wall portion of the frame in the other. Slightly pull up on the frame until the head Ball Stud of the shock lines up with the ball stud. Push the shock onto the ball stud until it clicks into place. Twist the head back and forth to Thin End of ensure it is secure.
- Page 3 6. Fill the liner cavities with new liners, close and lock the liner dispenser lid. Close the unit. ® Koala Kare Products ǁ 6982 S Quentin St. ǁ Centennial, CO 80112 Toll Free: 888.733.3456 ǁ 303.539.8300 ǁ Fax: 303.539.8399 www.koalabear.com...