Related Manuals for Seada G44 HDMI
Summary of Contents for Seada G44 HDMI
- Page 1 G44 HDMI User Guide This user guide provides basic instructions for setting up SEADA G44 HDMI video wall controllers using its management software. Document No. SD-EN-013 Document Version:...
-
Page 2: Table Of Contents
G44 HDMI User Guide Table of Contents Product Introduction ........................3 1.1. Product profile ........................3 1.2. Product capability ........................3 1.3. Specification & Parameters ....................4 Hardware Overview ........................5 2.1. Front Panel ..........................5 2.2. Rear Panel ..........................6 Connection Set up ........................... -
Page 3: Product Introduction
1.1. Product profile The G44 HDMI version of video wall controller accepts up to 4 HDMI inputs and displays them on 4 different displays, each with a resolution up to 4K@60fps 4:4:4. G44 not only allows the user to display a single input across all four screens, but also to display different input videos onto different screens working like a matrix switcher. -
Page 4: Specification & Parameters
G44 HDMI User Guide 1.3. Specification & Parameters Interface HDMI-A HDMI Version HDMI2.0, HDCP2.2 Bandwidth 18Gbps 800x600@60Hz,1024x768@60Hz, 1280x768@60Hz, 1280x800@60Hz,1280x1024@60Hz,1360x768@60Hz, 1366x768@60Hz,1400x1050@60Hz,1440x900@60Hz, 1600x1200@60Hz,1680x1050@60Hz, Input 1920x1200@60Hz,480p,576p,720p,1920x1080i, 1920x1080p,3840x2160@24Hz/25Hz/30Hz/50Hz/60Hz, 4096x2160@24Hz/25Hz/30Hz/50Hz/60Hz. Output 3840x2160@60Hz, 3840x2160@50Hz, 3840x2160@30Hz, 3840x2160@25Hz, 1920x1200@60Hz,1920x1080@60Hz, 1920x1080@50Hz,1600x1200@60Hz, 1400x1050@60Hz,1366x768@60Hz, 1360x768@60Hz, 1280x1024@60Hz, 1280x768@60Hz, 1280x720@60Hz, 1280x720@50Hz, 1024x768@60Hz HDMI Amplitude T.M.D.S +/- 0.4Vpp... -
Page 5: Hardware Overview
G44 HDMI User Guide 2. Hardware Overview 2.1. Front Panel • OUTPUT/INPUT Buttons Press buttons OUTPUT n + INPUT m+ TAKE by sequence, switch input n to output m • Lock Button Press button more than 2 seconds and less than 6 seconds, to lock or un-lock front buttons. When locked, the Lock LED will be on. -
Page 6: Rear Panel
G44 HDMI User Guide 2.2. Rear Panel • LAN(10M/100M/1000M) and RS232 Ports • IR IN and IR OUT IR IN/OUT routing follows video matrix routing • Audio Input 4 x 3-way Phoenix connectors to input external analog LR audio, user can select this audio to replace the corresponding embedded HDMI audio •... -
Page 7: Connection Set Up
4. G44H Software User Guide Users can run the G44H.exe software directly without installation. Software is on the disk in the package or you can download it from the SEADA website. Double click the G44H software to get the UI as below There are 8 main tabs in this software to help users set up and control the G44-HDMI video wall controller. -
Page 8: Matrix Switch
G44 HDMI User Guide 4.1. Matrix Switch Users can connect the G44 device to control PC and set up the device as matrix switcher in this section. 4.1.1. Connect to the G44 via UART for RS232 Connect the G44 to the control PC with a serial cable 1. - Page 9 G44 HDMI User Guide 4.1.4. Allset, Recall, Save As and Reset • The Allset dropdown menu helps the users select a single input to be displayed on all of the screens (i.e. Allset Input 4 would display Input 4 on Output 1, Output 2, Output 3 and Output4) •...
-
Page 10: Advanced Switch
G44 HDMI User Guide 4.2. Advanced Switch The Advanced Switch tab will repeatedly send a batch of matrix selection commands at the interval time specified in ‘Send cmd Periodically’ 1. Select one or more outputs. 2. Select one input. 3. Use the arrow button (-->) to assign that input to the selected output or outputs. -
Page 11: Signal Setting
G44 HDMI User Guide 4.3. Signal setting In the signal settings tab, the user can see the Input Resolution and Input Type as well as the Output Type and Resolution. The read all function will recognize the type and resolution automatically. - Page 12 G44 HDMI User Guide 4.4.2. Position Control The section highlighted in blue allows the user to fine-tune the position of their screen. Parameters such as H Start V start, and H Size and V Size will allow the user to adjust the starting position and the size of the screen (H –...
-
Page 13: Osd Setup
G44 HDMI User Guide 4.5. OSD Setup 4.5.1. Text Content There are several modes of OSD – Normal, 3x3 and 3x4. With the normal mode there will be only one column displayed at a time. Normal mode allows for more lines to be added as well. - Page 14 G44 HDMI User Guide • Read – This function will read any existing OSD settings on the screen. • Import – This allows the user to import any OSD settings from another control PC (Any settings that have not been saved on the device itself) •...
-
Page 15: Video Wall
G44 HDMI User Guide 4.6. Video Wall Click to select the screen, then drag & select the screens to splice, right-click, and click Screen splicing to form a video wall • Screen Splicing - This combines the selected screens into one and displays the selected input across all of the splicing screens. -
Page 16: Cec Control
When Auto Power On is enabled, once G44 is powered up, all the video source devices and displayers, which support CEC, connecting to G44 unit will be switched on. G44 HDMI version CEC function include Power on/off, Volume+/-,Mute/Unmute 4.8. Network Setting... -
Page 17: Troubleshooting
G44 HDMI User Guide 5. Troubleshooting 5.1. No Connection 5.1.1. Ensure the G44 is powered up 5.1.2. Ensure the PC and G44 at the same IP group 5.1.3. Ensure the IP address is correct for G44 5.1.4. IP address of each device will be shown on screen when no video input is applied. - Page 18 G44 HDMI User Guide SEADA Technology Ltd Oak Tree Park Burnt Meadow Road Moons Moat North Industrial Estate Redditch Worcestershire B98 9NW United Kingdom Email: sales@seada.co.uk Phone: +44 (0)1527 584364 Fax: +44 (0)1527 962998...
Need help?
Do you have a question about the G44 HDMI and is the answer not in the manual?
Questions and answers