S&C IntelliRupter PulseCloser Instruction Sheet
  1. Manuals
  2. Brands
  3. S&C Manuals
  4. Industrial Electrical
  5. IntelliRupter PulseCloser
  6. Instruction sheet
S&C IntelliRupter PulseCloser Instruction Sheet

S&C IntelliRupter PulseCloser Instruction Sheet

Fault interrupter wi-fi, scada, and gps communication setup
Hide thumbs Also See for IntelliRupter PulseCloser:
Table of Contents

Advertisement

Quick Links

Download this manual
IntelliRupter
®
PulseCloser
Outdoor Distribution (15.5 kV, 27 kV, and 38 kV)

Table of Contents

Section
Qualified Persons . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Read this Instruction Sheet . . . . . . . . . . . . . . . . . . . 2
Retain this Instruction Sheet . . . . . . . . . . . . . . . . . . . 2
Proper Application . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Special Warranty Provisions . . . . . . . . . . . . . . . . . . . 2
Understanding Safety-Alert Messages . . . . . . . . . . . 4
Following Safety Instructions . . . . . . . . . . . . . . . . . . 4
Replacement Instructions and Labels . . . . . . . . . . . 4
. . . . . . . . . . . . . . . . . . . . . . . . . 5
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Removing the Communication Module . . . . . . . . . . 7
Replacing the Battery . . . . . . . . . . . . . . . . . . . . . . . . 8
Installing a Radio . . . . . . . . . . . . . . . . . . . . . . . . . . .10
February 17, 2020
© S&C Electric Company 2008-2020, all rights reserved
®
Fault Interrupter
Wi-Fi, SCADA, and GPS
Communication Setup
Page
Section
Wi-Fi Capability . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Wi-Fi Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
SCADA Capability . . . . . . . . . . . . . . . . . . . . . . . . . . .15
DNP Implementation . . . . . . . . . . . . . . . . . . . . . . . .15
SCADA Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
SCADA Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
GPS Capabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
GPS Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
GPS Setup and Diagnostics . . . . . . . . . . . . . . . . . . .16
Instruction Sheet 766-520
Page

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the IntelliRupter PulseCloser and is the answer not in the manual?

Questions and answers

Related Manuals for S&C IntelliRupter PulseCloser

Summary of Contents for S&C IntelliRupter PulseCloser

  • Page 1: Table Of Contents

    IntelliRupter ® PulseCloser ® Fault Interrupter Outdoor Distribution (15.5 kV, 27 kV, and 38 kV) Wi-Fi, SCADA, and GPS Communication Setup Table of Contents Section Page Section Page Introduction Wi-Fi Communication Setup Qualified Persons . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Wi-Fi Capability .

  • Page 2: Introduction

    Instruction Sheet Read this instruction sheet thoroughly and carefully before installing or operating your IntelliRupter PulseCloser Fault Interrupter . Familiarize yourself with the Safety Information and Safety Precautions on pages 4 and 5 . The latest version of this publication is available online in PDF format at sandc.com/en/ support/product-literature/ .
  • Page 3 Introduction Replacement parts provided by the seller or repairs performed by the seller under the warranty for the original equipment will be covered by the above special warranty provision for its duration. Replacement parts purchased separately will be covered by the above special warranty provision.

  • Page 4: Safety Information

    Safety Information Understanding Several types of safety-alert messages may appear throughout this instruction sheet and on labels attached to the IntelliRupter PulseCloser Fault Interrupter. Familiarize Safety-Alert Messages yourself with these types of messages and the importance of these various signal words: DANGER “DANGER”...

  • Page 5: Safety Precautions

    Safety Precautions DANGER IntelliRupter PulseCloser Fault Interrupters operate at high voltage. Failure to observe the precautions below will result in serious personal injury or death. Some of these precautions may differ from your company’s operating procedures and rules . Where a discrepancy exists, follow your company’s operating procedures and rules .

  • Page 6: Overview

    Overview These instructions cover the Wi-Fi, SCADA, and GPS communication setup of an IntelliRupter PulseCloser Fault Interrupter. The communication module contains a Wi-Fi transceiver, a GPS receiver, and, if specified, a radio providing wide-area network capability in SCADA applications. The communication module may also include...

  • Page 7: Communication Module

    Communication Module Maintenance The communication module can be easily removed and replaced using a hookstick for maintenance of the battery, Wi-Fi transceiver, GPS receiver, and radio. NOTICE To prevent contamination of the connectors, avoid routine battery replacement during inclement weather, and never place the connector on the ground without some form of protection from dirt and mud .

  • Page 8: Replacing The Battery

    Communication Module Replacing the Battery Perform the following procedure to replace the battery in the communication module: STEP 1. Loosen the battery compartment cover locking screw using a ⅜ -inch nut driver. See Figure 4. STEP 2. Open the battery compartment cover. See Figure 5.
  • Page 9 Communication Module STEP 4. Using the fi nger-pull, slide out the existing battery and slide in the replacement battery. See Figure 7. Reconnect the battery leads. STEP 5. Close the battery compartment cover and securely tighten the battery compartment cover locking screw.

  • Page 10: Installing A Radio

    Communication Module Installing a Radio A radio providing wide-area network capability for SCADA applications, if specified, is furnished factory-installed in the communication module. Alternately, a user-furnished radio can be installed in the field. Some radios must be programmed using a cable connected to a computer. In such instances, remove the radio tray assembly to connect to the radio, and power the radio with the battery or a separate power supply.
  • Page 11 Communication Module The radio tray mounting plate, with connections for Wi-Fi/GPS module Wi-Fi/GPS module Battery power, data, and antenna, will be accessible. See Figure 9. Ethernet 2 Ethernet 1 connector STEP 4. Install the radio on the mounting plate using the furnished hardware.
  • Page 12 Communication Module STEP 6. Connect the antenna connector to the radio. Ethernet connector Power plug STEP 7. Reinstall the radio tray assembly, and replace and securely tighten the fi ve ¼–20 bolts. Close the battery compartment cover, and tighten the battery compartment cover screw.

  • Page 13: Reinstalling The Communication Module

    Communication Module Reinstalling the Communication Module The communication module can be installed from a bucket truck with the module handling fitting, catalog number 4450, attached to a suitable hookstick. CAUTION The communication module is heavy. Removal and replacement from the ground using an extendostick is not recommended .

  • Page 14: Wi-Fi Communication Setup

    Wi-Fi Communication Setup Wi-Fi Capability The Wi-Fi transceiver in the communication module provides secure wireless point-to-point communication to a wireless-equipped personal computer operating under the IEEE 802.11b standard. Transmission range is typically 150 feet (45.7 meters) or less. The Wi-Fi connection permits local configuration and control of the IntelliRupter fault interrupter.

  • Page 15: Scada Communications Setup

    SCADA Communication Setup SCADA Capability The IntelliRupter fault interrupter can communicate with a SCADA system via the DNP protocol by using a WAN radio or fiber-optic transceiver installed in the communication module. Alternately, an appropriate SCADA communication device can be housed in a separate pole-mounted enclosure.

  • Page 16: Gps Communications Setup

    GPS Communication Setup GPS Capabilities A global positioning system (GPS) receiver installed in the communication module provides precise time synchronization. The system allows rapid analysis of event records, simplifying the determination of a sequence of events. GPS Antenna The factory-installed GPS antenna is located on the top of the base as shown in Figure 16.

Table of Contents