Compu Link Control System; Dubbing; Tape Editing - JVC TD-W717TN Service Manual

H H
D O
i
o
V | *
s |
z :
CO
^
J
o
COH
4
^
*
COMPU LINK CONTROL SYSTEM
DUBBING
> o
$ ^
CO
CJ 1
CO 5
Notes :
•
Synchronized recording or DDRP recording stops automati
-
cally when the CD player stops playing
.
•
Synchronized recording does not start except when the
record
-
pause mode is set by simultaneously pressing
the # REC / REC MUTE and
ll
PAUSE buttons In the stop
mode
.
•
To cancel synchronized recording or DDRP recording
,
press
the STOP button of the CD player or cassette
deck
.
•
The source Is locked to the
CD position during synchronized
recording or DDRP recording to avoid accidental stops or
switch
- over to another component
.
To switch over the com
-
ponents , cancel synchronized recording or DDRP recording
first
.
•
The INPUT LEVEL control does not function during DDRP
recording
.
2
COMPULINK •
Synchro dubbing
Operate in the order of the numbers in the illustration
.
When deck B stops , the dubbing mode is automatically
released
.
•
Synchro
record muting
When deck A stops or enters any mode other than the play
-
back mode during dubbing
,
deck B enters the record mute
operation automatically and then
enters
the
record
-
pause
mode
.
D
ControlSysfm
H
The Compu Link Control System controls relative operations
between
components automatically and facilitates various oper
-
ations
.
This is a system originated and developed by JVC for facilitat
-
ing various system operations
.
There are two versions of this
system
; version 1 and 3 .
( For version 1 components
,
" COMPU
LINK
-
1 / SYNCHRO '' is marked on the rear panel
.
For version 3
components
,
" COMPU LINK - 3 / SYNCHRO " is marked on the
rear panel
.
This unit belongs to version 3
.
)
The version 3 system controls relative functions between this
unit and an amplifier or receiver , in addition to all of the func
-
tions of version 1
.
o
POWER
•
Before pressing the SYNCHRO DUBBING button
Confirm that both decks are in the stop mode before starting
dubbing
.
Dubbing and DOLBY NR switch
During dubbing
,
the same NR
mode selected for the playback
cassette is applied to the recording cassette , regardless of the
position of the NR switch
.
Automatic Power On/OH ( STANDBY ) Function ( COMPU
LINK
-
3 )
This
function
is available when
an amplifier or receiver having
a COMPU LINK
-
3 / SYNCHRO terminal is connected
-
For exam
-
ple , if a deck contains a tape ,
the
deck is turned on
automati
-
cally and the tape Is played back by only pressing the PLAY
button
.
When the amplifier or receiver is switched to STANDBY ,
the source unit is automatically switched
to
STANDBY
.
Dubbing and BLANK SKIP
When the BLANK SKIP button is ON during normal
-
speed dub
-
bing , the BLANK SKIP function operates in deck A
.
When deck A enters in the BLANK SKIP mode
,
deck B enters
standby status for the record
-
pause mode after automatic
record muting operation
.
When deck A resumes playback ,
dubbing commences
.
Automatic Source Selection ( COMPU LINK - 1
, 3
)
When the provided remote cables are used for connecting this
unit to other
components
which have COMPU LINK
-
1 or
3 / SYNCHRO terminals
,
the switch - over of all system compo
-
nents is possible with simple one
-
touch of the source selector
button
of JVC ' s amplifier or receiver
.
By doing this
,
the corresponding component will start playing
automatically
.
The
source selector button of the remote control unit or the
activation button of the desired component can be also used for
this purpose
.
When the components have been switched over
,
the
previous component will
stop
playing within five seconds
.
o o
Input level
Recording is performed at the same level as
the playback tape
during dubbing regardless of the position of the INPUT LEVEL
control
.
n n n
u . uu
COUNTER RESET
REVERSE
Moce
Microphone mixing
during dubbing
By connecting a microphone
,
microphone mixing during dub
-
bing is possible with the playback sounds from
deck A
. Be sure
to perform dubbing at normal speed
.
When performing micro
-
phone mixing during dubbing , use cassettes recorded with NR
OFF mode for the deck A
.
o
A
*
, a
SYNCHRO DUE 8 M 5
NORM SPEED HIGH SPEED
Tape editing
1
.
Press the
•
REC / REC MUTE button when finished dubbing
a
tune .
Deck B automatically enters the record muting mode
and leaves a non
-
recorded
section of
about 4
- seconds then
enters the record - paused mode
.
2
.
Press the ( stop ) button of deck A and search for the next
tune you want by using the , « or PLAY button
.
Then
stop the cassette just before the beginning of the tune
.
3
.
Press the same SYNCHRO DUBBING button pressed before
the pause again
,
and dubbing will start
.
Synchronized Recording ( COMPU LINK - 1
, 3
)
Synchronized recording refers to the process In which the deck
starts recording in synchronism with the CD player
.
Perform the
synchronized recording as follows :
1
.
Set the cassette
deck to
the record -
pause mode in accor
-
dance with the recording procedures on page 8
.
2
.
If you want the programmed recording , program the desired
tunes in
any order you wish to hear
.
3
.
Press
the PLAY
/ PAUSE button of the CD player
.
By so
doing
,
the cassette deck is placed in the record mode and
synchronized with the CD player for recording
.
Synchro -
nized recording thus can be made possible
.
O Press the POWER switch to set to ON
.
O
Insert a prerecorded tape
with
side A facing out into deck A
,
and press the
-
o
( direction ) button to select the travel
direction
.
Q Insert the blank
tape
with side A facing out into deck B , and
press
the
- «
( direction ) button to select the side
to be
recorded
.
O Select the REVERSE MODE
.
Q Press to " 0.00 ' '
.
O Press the SYNCHRO DUBBING ( NORM or HIGH SPEED ) but
-
ton to start dubbing
.
Q Press the ( stop ) button of deck B to stop dubbing
.
Notes at dubbing
1
.
Normal - speed dubbing is recommended to obtain good
sound quality
.
2
.
Television
receivers placed
close to the deck may cause
interference on the recorded signal when the deck is used
in the high
-
speed dubbing mode
.
If this happens
,
either turn
off the television receiver or use the normal
-
speed dubbing
mode
.
DDRP ( Dynamics Detection Recording Processor ) recording
The DDRP function makes possible fully automatic recording
when used
with a suitable JVC CD player
.
When the DDRP but
-
ton of a suitable JVC CD player is pressed , the recording level
is first adjusted automatically , then recording starts ; it is not
necessary to start recording by the normal procedure
.
-
12
-
-
11
-