Summary of Contents for Lincoln Electric Weld Booth
Page 1
Operator’s Manual Weld Booth Need Help? Call 1.888.935.3877 Register your machine: to talk to a Service Representative www.lincolnelectric.com/register Authorized Service and Distributor Locator: Hours of Operation: www.lincolnelectric.com/locator 8:00 AM to 6:00 PM (ET) Mon. thru Fri. Save for future reference After hours? Use “Ask the Experts”...
Page 2
THANK YOU FOR SELECTING A QUALITY PRODUCT BY KEEP YOUR HEAD OUT OF THE FUMES. DON’T get too close to the arc. LINCOLN ELEC TRIC. Use corrective lenses if necessary to stay a reasonable distance away from the arc. READ and obey the Safety Data PLEASE EXAMINE CARTON AND EQUIPMENT FOR Sheet (SDS) and the warning label DAMAGE IMMEDIATELY...
W117.2-1974. A Free copy of “Arc Welding Safety” booklet E205 is available from the Lincoln Electric Company, 2.d. All welders should use the following procedures in order to 22801 St. Clair Avenue, Cleveland, Ohio 44117-1199.
SAFETY ELECTRIC SHOCK ARC RAYS CAN BURN. CAN KILL. 3.a. The electrode and work (or ground) circuits are 4.a. Use a shield with the proper filter and cover plates to protect your electrically “hot” when the welder is on. Do eyes from sparks and the rays of the arc when welding or not touch these “hot”...
Page 5
SAFETY WELDING AND CUTTING CYLINDER MAY EXPLODE IF SPARKS CAN CAUSE DAMAGED. FIRE OR EXPLOSION. 7.a. Use only compressed gas cylinders containing the correct shielding gas for the process used 6.a. Remove fire hazards from the welding area. If and properly operating regulators designed for this is not possible, cover them to prevent the welding sparks the gas and pressure used.
Page 7
Dimensions anD WeiGhts of WelD Booths Weld Booth Panels are shipped in a protected crate as shown in Fig. A.1. Crate dimensions are 98”L x 30”W x 36”H. Each crate can have up to 14 panels and 12 posts.
Page 8
Item#2: L15788-117 5 FT, RIGHT SIDE PANEL Item#3: L15788-113 4 FT, CENTER-BACK PANEL Item#3: L15788-118 5 FT, CENTER-BACK PANEL Item#4: L15788-114 4-5 FT BOOTH, WELD BOOTH POST (QTY 4) Item#4: L15788-114 4-5 FT BOOTH, WELD BOOTH POST (QTY 4) Item#5: L15788-115 4 FT, HEADER TUBE...
Page 9
Item#1: L15788-120 6 FT, LEFT SIDE PANEL Item#2: L15788-121 6 FT, RIGHT SIDE PANEL Item#3: L15788-122 6 FT, CENTER-BACK PANEL Item#4: L15788-132 6 FT BOOTH, WELD BOOTH POST (QTY 4) Item#5: L15788-123 6 FT, HEADER TUBE Item#6: L15788-9 6 FT, WELD CURTAIN (OPTIONAL) Hardware Kit: AD1319-14 &...
Page 10
Cardboard Note logo orientation Note: Right side panel has Lincoln Electric Logo on Top Left side when panel is in vertical position Cardboard Note: Left side panel has Lincoln Electric Logo on Top Right side when panel is in vertical position.
Page 11
WELD BOOTH INSTALLATION Step 3. Anchor assemblies from step 1 and 2 to the floor at Step 4. Fasten Back side panel to left and right assemblies from required distance (See Fig. A.8): step 3. Hardware required is the same as in step 1. See Fig. A.9 FIG.
Page 12
WELD BOOTH INSTALLATION Step 5. Add header tube above back side panel. Connect it to posts and connect it to back side panel. (See Fig. A.10) Picture below shows header tube assembled to the posts and back panel. Note: To connect header tube to posts and back side panel use AD1319-13 hardware kit.
Page 13
WELD BOOTH INSTALLATION Booths siDe-By-siDe in a roW confiGuration for 4ft anD 5 ft Booths: This configuration will be assembled using the same principles as a single booth. (See Fig. A.11) A) Assemble Left side panel to two posts (1)
Page 14
WELD BOOTH INSTALLATION Back to Back Booths confiGuration 3. Add Center-Back Panels. Use AD1319-12 hardware kit. (See FIG. A.14 for 4 ft anD 5 ft Booths: Fig. A.14) This configuration will be assembled using the same principles as a single booth.
Page 15
WELD BOOTH INSTALLATION 4. Add Header tube. Use AD1319-13 KIT. (See Fig. A.15) FIG. A.15 Right Side Header tube Panel Left Side Left Panel Side Panel Right Side Panel...
Page 16
4. B.O. 3/8” Hex Nut (Qty 4 pcs) Left Side panel: It consists of two pieces that need to be bolted together by end user. Top piece will have Lincoln Electric logo on top right side. Bottom piece will be blank (See fig. A.16).
Page 17
WELD BOOTH INSTALLATION FIG. A.19 Note: Distance between 6 ft panels (posts) See Fig. A.19 A-11...
Page 18
WELD BOOTH INSTALLATION Hardware needed to connect header tube to panels and posts is FIG. A.20 AD1319-15 See Fig. A.20 A-12...
Page 19
4 ft Booth Weld Curtain (L15788-45) components: Step 1. Position Universal Mounting bracket 1” off of the edge of the Weld Booth tubing per picture below. Drill holes on the post and use No. 12 self-tapping screws to assemble bracket.
Page 22
WARNING Do not touch electrically live parts or Keep flammable materials away. Wear eye, ear and body protection. electrode with skin or wet clothing. Insulate yourself from work and AVISO DE ground. Spanish PRECAuCION No toque las partes o los electrodos Mantenga el material combustible Protéjase los ojos, los oídos y el bajo carga con la piel o ropa moja-...
Page 23
WARNING Keep your head out of fumes. Turn power off before servicing. Do not operate with panel open or Use ventilation or exhaust to guards off. remove fumes from breathing zone. AVISO DE Spanish PRECAuCION Los humos fuera de la zona de res- Desconectar el cable de ali- No operar con panel abierto o piración.
Page 24
Lincoln Electric for advice or information about their use of our products. We respond to our customers based on the best information in our possession at that time. Lincoln Electric is not in a position to warrant or guarantee such advice, and assumes no liability, with respect to such information or advice.