Table of Contents
Advertisement
Electronic Service
Manuals
This electronic document is provided as a service to our customers.
We do not create the contents of the information contained in this docu-
ment. Should you have detailed questions pertaining to the information
contained in this document, you may contact Michco, or the manufac-
turer which provided the original information in this electronic deliver-
able. Michco's only part in this electronic deliverable was the electronic
assembly process. By providing this manual on line we are not guaran-
teeing parts availability.
You may contact Michco through the following methods:
Phone (517) 484-9312 or (800) 331-3339
2011 N. High St. -- Lansing, Michigan -- 48906
Fax: (517) 484-9836
Email: CustServe@Michco.com
Web site: www.Michco.Com
Parts Web site: www.FloorMachineParts.Com
Order Parts on Line at:
www.FloorMachineParts.Com
Directly to Parts & Service:
By Email:
Shop@Michco.com
By Fax: (517) 702-2041
By Voice: Use numbers above.
Serving the Cleaning Industry Since 1922
Notice: All copyrighted material remains property of original owners, all trademarks are property of respective owners.
Manuals are subject to Manufacturer's reproduction limitations. Originals or reproductions were provided by manufacturers
through a request. We make no warranty as to the correctness of information provided in this document and you assume
all risk. By placing these manuals on line we are not declaring our corporation to be an manufacturer authorized dealer or
provider, please check our web site for authorized manufacturers we represent.
Advertisement
Table of Contents
Related Manuals for Minuteman 829 Asbestos Series
Summary of Contents for Minuteman 829 Asbestos Series
- Page 1 Electronic Service Manuals This electronic document is provided as a service to our customers. We do not create the contents of the information contained in this docu- ment. Should you have detailed questions pertaining to the information contained in this document, you may contact Michco, or the manufac- turer which provided the original information in this electronic deliver- able.
- Page 2 Parts and Instruction Manual X829 Asbestos Series 15 & 20 Gallon...
- Page 3 This manual is furnished with each new MINUTEMAN X829 Asbestos Vacuum. This provides the necessary operating and preventive maintenance instructions. Operators must read and understand this manual before operating or servicing this machine. This machine was designed to give you excellent performance and efficiency. For best results and minimal cost, please follow the general guidelines below: ·...
-
Page 4: Table Of Contents
Lid Assembly BOM .......................... 8 Bag Assembly ..........................9 Adapter Assembly ......................... 10 Tank Assembly ..........................11 Tank Assembly BOM ........................12 Optional Industrial Tools and Accessories ..................13 Minuteman International Made Simple Commercial Limited Warranty ........14 Parts and Instruction Manual... -
Page 5: Important Safety Instructions
FOR COMMERCIAL USE ONLY IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING WARNING - To reduce the risk of fire, electric shock, or injury: Do not leave appliance when plugged in. Unplug from outlet when not in use and before servicing. WARNING To reduce the risk of electric shock - Do not expose to rain. -
Page 6: Inspection
INSPECTION Carefully unpack and inspect your machine for shipping damage. Each unit is tested and thoroughly inspected before shipment, and any damage is the responsibility of the delivery carrier who should be notified immediately. ELECTRICAL 115 Volt This machine is designed to operate on a standard 15 amp. 115 volt, 60 hz, AC circuit. Voltages below 105 volts AC or above 125 volts AC could cause serious damage to the motor. -
Page 7: User Maintenance Instructions
WARNING This vacuum may contain potentially hazardous dust depending on its application. Special handling of contaminated disposable bags and filters is recommended. Disposal must be in compliance with local EPA regulations. USER MAINTENANCE INSTRUCTIONS All service and repair should be performed by qualified vacuum service representative or electrician. No user serviceable components are employed in the electrical vacuum lid head assembly. -
Page 8: Tank/Filter Set-Up Procedure
(refer to Main Assembly) TANK/FILTER SET-UP PROCEDURE 1. When using the poly adapter for dry pick-up follow the described procedures below for poly 6 mil. bag installation. A. Insert poly bag into tank assembly draping all excess bag height over the edge of tank. Fully open bag inside tank to ensure that the bag is not bunched up and fully extended to the bottom of tank. -
Page 9: Warning Instructions For 800012 & 805037 Plastic Bags
WARNING INSTRUCTIONS FOR 800012 & 805037 PLASTIC BAGS TO PREVENT OVERHEATING AND DAMAGE TO THE MACHINE PLEASE FOLLOW THE INSTRUCTIONS BELOW! After placing the plastic recovery bag inside the tank, use a sharp knife to cut a 1” slit in the bag at the top edge of the tank, on the side opposite the vacuum intake. -
Page 10: Exploded Views
Exploded Views Main Assembly Poly Tank With 1:1 Adapter 1. Motor Lid Assembly 2. Cloth Fliter with Frame 3. Filter Protector 4. 1:1 Poly Adaptor 5. Plastic Liner for Top Fill Dry Pickup 6. 15/20 Gallon Poly Tank Parts and Instruction Manual Page 6... - Page 11 Parts and Instruction Manual Page 7...
-
Page 12: Lid Assembly Bom
Lid Assembly BOM Bill of Material - 829123 / 829240 ITEM PART NO. REQ’D DESCRIPTION 110029 FILTER-ULPA, X829 SERIES 110030PKG 1 PREFILTER SLEEVE, 829/839, PKG OF 6 290017 MOULDED VAC MOTOR GASKET 380035 GASKET, 4.31 X 5.81 X.19 290030 LID GASKET DIECUT 15G 290 380064 RING, FOAM 381020... -
Page 13: Bag Assembly
Bag Assembly Bill of Material - 805057 Item No. Part No. Qty. Description 750097 Bag Frame Weldment Asy 760131 Molded Bag Ring - Black 805054 Cloth Bag Only New Style 805057 Bag Assy. Complete w/Frame Parts and Instruction Manual Page 9... -
Page 14: Adapter Assembly
Adapter Assembly Bill of Material - 800420 ITEM PART NO. REQ’D DESCRIPTION 380046 BALL, HOLLOW RUBBER 390001 MOLDED TRIGGER 390002 SPRING-RETURN (390001) 390035 LATCH-390 SERIES COATED 390037 ADAPTER POLY 1:1 BURGUNDY 390087 GASKET DIECUT VNN 390088 GASKET PS BACK 1:1 POLY 390101 INTAKE 390108... -
Page 15: Tank Assembly
Tank Assembly Parts and Instruction Manual Page 11... -
Page 16: Tank Assembly Bom
Tank Assembly BOM Bill of material - 390040 / 390050 ITEM PART NO. REQ’D DESCRIPTION 390031 HANDLE PLT 390 SERIES 390033 AXLE 390 SERIES PLATED 390035 LATCH-390 SERIES COATED 390041 TANK 15GRC NO HOLES 390051 TANK 20GRC W/ NO HOLES 710182 SCR-MC 1/4-20 X 1.00 ZINC 711352... -
Page 17: Optional Industrial Tools And Accessories
Optional Industrial Tools and Accessories 800024 3" Rd. Dust Brush Complete 800022 5" Rd Dust Brush Complete 800023 Bristle Insert 5" 800175MCH Dust Brush HSG 5" 800176MCH Dust Brush HSG 3" 800025 Bristle Insert 3" 800034 24" Crev Tool Aluminum, Complete 800015 Wand Assy. -
Page 18: Minuteman International Made Simple Commercial Limited Warranty
A potential health hazard exits without original equipment replacement. All warranted items become the sole property of Minuteman or its original manufacturer, whichever the case may be. Minuteman disclaims any implied warranty, including the warranty of merchantability and the warranty of fitness for a particular purpose.