Related Manuals for Huawei UPS2000-A-1 kVA
Summary of Contents for Huawei UPS2000-A-1 kVA
- Page 1 UPS2000-A-(1 kVA-3 kVA) Quick Guide Issue: 08 Date: 2020-05-18 HUAWEI TECHNOLOGIES CO., LTD.
- Page 2 (3) Universal serial bus (USB) port (security protection (4) RS232 port mechanism supported) (5) Optional card slot (6) External battery connector (only for long backup time models) (7) Output socket (C13) (8) Output socket (C19) Copyright © Huawei Technologies Co., Ltd. 2020. All rights reserved.
- Page 3 Installing a Single UPS 1. Use fully insulated tools during installation and operations. 2. Only engineers certified by the manufacturer or its agents are allowed to perform UPS installation, commissioning and maintenance. Otherwise, personal injury or equipment damage may occur, and the resulting UPS faults are beyond warranty scope. Before installation, read the UPS2000-A-(1 kVA-3 kVA) User Manual to get familiar with UPS information and safety precautions.
- Page 4 For details about how to install and use the iManager NetEco 1000U, see the iManager NetEco 1000U User Manual. The software and the user manual are available at https://support.huawei.com https://support.huawei.com/enterprise. Connect the UPS to the RS232 or USB port on a PC. Then you can monitor the UPS status using the PC as long as you have installed the monitoring software.
- Page 5 1KTTL/1KTTL-01 3KTTL/3KTTL-01 2KTTL/2KTTL-01 Installing the UPS Input Cable Take out input power cable from the fitting bag, and connect mains input power cable to the UPS. 1KTTS/1KTTS-01 2KTTS/2KTTS-01 3KTTS/3KTTS-01 1KTTL/1KTTL-01 3KTTL/3KTTL-01 2KTTL/2KTTL-01 Installing the Optional Card to the UPS If the product model has the suffix -01, optional cards are not supported. For the installation procedure, see the RMS-SNMP01B SNMP Card User Manual, RMS-RELAY01B User Manual, and RMS-MODBUS01B User Manual.
-
Page 6: Verifying The Installation
3KTTL 2KTTL 1KTTL Verifying the Installation Item Acceptance Criterion Cable routing Cable routing meets engineering requirements. Cable connections Power cables and battery cables are tightened to specified torques using a torque wrench, connected correctly, and free of damage. Cable connections for USB ports and Cables to USB ports and network ports are network ports connected correctly and securely. - Page 7 Setting Key UPS Parameters 1. The 1 kVA UPS with standard backup time have two built-in batteries. The 2 kVA UPS with standard backup time have four built-in batteries. The 3 kVA UPS with standard backup time have six built-in batteries. 2.
- Page 8 Starting the UPS to Inverter Mode When the UPS is connected to the Mains Input, it is no output. Hold down ON/MUTE on the front panel for over 5 seconds to make it transfer to inverter mode output. The default output of inverter mode is 230 V.
-
Page 9: Troubleshooting
Troubleshooting Symptom Possible Cause Measures The main power is The mains input power cable is Check the input power cable. normal, but no indicator disconnected. turns on and the buzzer The mains input power cable is Correctly connect the mains input generates no tone. -
Page 10: Alarm Handling
Alarm Handling For more alarm handling, see the UPS2000-A-(1 kVA-3 kVA) User Manual. Alarm Alarm Alarm Trigger Impact on the Repair Proposal Name Sever Clear Condition System Mode Bypass Minor This The bypass The UPS remains Possible cause: The voltage alarm is voltage is in the current... - Page 11 Alarm Alarm Alarm Trigger Impact on the Repair Proposal Name Severit Clear Conditi System Mode • Battery Critical This This alarm is Possible cause: overvol alarm voltage generated because The actual tage must of each there are more number of battery batteries than batteries does not...
- Page 12 Measure: Contact the Minor This The voltage of The UPS remains dealer or alarm each battery is in the current Huawei lower than 5 state and cannot technical autom V, or is higher start. support to aticall than 15 V...
- Page 13 Check that the load types are supported by the UPS. • Possible cause: The hardware is damaged. Measure: Contact the dealer or Huawei technical support. HUAWEI TECHNOLOGIES CO., LTD. Huawei Industrial Base, Bantian, Longgang Shenzhen 518129 People's Republic of China www.huawei.com...