Advertisement
Quick Links
Daily Cleaning Instructions: KL1
Clean the following components at least once daily. Clean more frequently if your pharmacy
dispenses many dust‐generating medications or if you experience counting errors.
Materials: 70% isopropyl alcohol or mild soapy water (e.g., dish soap), lint‐free cloth or
paper towels. Do not use facial tissue, cotton balls or cotton swabs.
Before starting, turn off the unit and unplug it.
1. Funnel
A. Remove the funnel from the unit.
B. Clean outside and inside thoroughly with alcohol or mild soapy water.
2. Glass Detector Windows
The unit's counting sensors are located behind the removable inside channel assembly.
Most counting errors are caused by pill dust accumulating on the edges and corners of
the glass windows on the inside channel assembly. Clean the windows well.
A. Unscrew the two round thumb screws on top of the unit. Remove the
square guard.
B. Lift out the entire inside channel assembly.
C. Wipe off excess pill dust on the inside of the four glass windows with a dry cloth.
D. Wet a clean cloth with alcohol or mild soapy water and clean the inside of the four
glass windows thoroughly to remove all remaining dust and residue. Wipe back‐and‐
forth, not up‐and‐down. Do not press hard as this may break the glass windows. Do
not remove the individual glass panes unless Service instructs you to.
E. Fold the cloth to form a "point" to carefully clean any edge or corner where dust can
accumulate. Pay special attention to corners.
F. Wipe the glass windows dry with a clean cloth. Hold the inside channel assembly up
to a light to visually inspect the glass windows for any dust, fingerprints, or streaks.
Re‐clean if necessary. Wipe dry.
G. Look down inside the device and visually inspect the four inside glass windows
for dust or streaks. If necessary, clean with water and wipe dry.
H. Replace the inside channel assembly and square guard. Tighten the round thumb
screws until snug. Do not over‐tighten the thumb screws.
Step 1A – Remove
Square Guard
Steps 2C‐F, Inside
Channel Assembly:
Clean inside and
outside of 4 glass
windows without
removing or
damaging the panes
5DIM‐3802‐DCI 5/2016
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Kirby Lester KL1
Summary of Contents for Kirby Lester KL1
- Page 1 Daily Cleaning Instructions: KL1 Clean the following components at least once daily. Clean more frequently if your pharmacy dispenses many dust‐generating medications or if you experience counting errors. Materials: 70% isopropyl alcohol or mild soapy water (e.g., dish soap), lint‐free cloth or paper towels. Do not use facial tissue, cotton balls or cotton swabs. Before starting, turn off the unit and unplug it. 1. Funnel A. Remove the funnel from the unit. B. Clean outside and inside thoroughly with alcohol or mild soapy water. Step 1A – Remove Square Guard 2. Glass Detector Windows The unit’s counting sensors are located behind the removable inside channel assembly. Most counting errors are caused by pill dust accumulating on the edges and corners of the glass windows on the inside channel assembly. Clean the windows well. A. Unscrew the two round thumb screws on top of the unit. Remove the square guard. B. Lift out the entire inside channel assembly. C. Wipe off excess pill dust on the inside of the four glass windows with a dry cloth. D. Wet a clean cloth with alcohol or mild soapy water and clean the inside of the four glass windows thoroughly to remove all remaining dust and residue. Wipe back‐and‐ forth, not up‐and‐down. Do not press hard as this may break the glass windows. Do not remove the individual glass panes unless Service instructs you to. E. Fold the cloth to form a “point” to carefully clean any edge or corner where dust can accumulate. Pay special attention to corners. F. Wipe the glass windows dry with a clean cloth. Hold the inside channel assembly up ...
- Page 2 If desired, the glass window holder can be removed from the inside channel assembly for a more thorough cleaning and visual inspection. Gently push down on the square sliding ring, which spreads the two black clips holding the glass window holder. Take special care not to break the black clips. 3. Counting Tray Clean thoroughly with mild soapy water. Do not use alcohol. Step 2I – Visually Inspect Glass Windows 4. Tray Sensor Located on the KL1 behind the counting tray when the tray is fully inserted. This sensor tells the unit that the tray is properly seated. With the tray removed, clean the sensor window with water. Wipe dry to remove streaks. Step 4 – Note about the use of mild soapy water versus isopropyl alcohol: Mild soapy water and alcohol Tray Sensor both provide appropriate sanitary cleansing. Water leaves fewer streaks than alcohol on a Kirby Lester device's inside glass sensor windows. If streaks are found after cleaning, use just water and wipe dry. In general, prolonged alcohol exposure causes faster wear‐and‐tear on plastic. 5. Cleaning and Troubleshooting Problem or Error Code Probable Cause Possible Solution(s) E‐2, E‐4, E‐9, O‐S or unit counts by Tablet dust or residue on glass windows, or Clean glass windows thoroughly. Or replace itself replace cracked glass window. cracked glass window. Overcounts (more counted than ...
Need help?
Do you have a question about the KL1 and is the answer not in the manual?
Questions and answers