Table of Contents
Advertisement
Before starting the equipment
6.1 Assembly
6.1.1 Fitting the push bar (Fig. 3 & 4)
The push bar is fully pre-assembled and must only
be swung out and adjusted to the required height.
To do so, undo the quick lock levers for the upper
push bar (Figure 3/Item 3) and unfold the top push
bar. Then secure the top push bar again with the
quick lock levers. Now release the quick-lock wheels
for the lower push bar (Figure 4/Item 6) by turning
them, move the push bar to the required position
and secure by turning the wheels in the opposite
direction.
6.1.2 Fitting the grass catcher (Fig. 5)
To assemble the grass catcher, insert the lugs of
the left side of the grass catcher carefully into the
openings on the right side of the grass catcher and
push the two parts together. Then insert the lugs
of the upper part of the catcher carefully into the
openings on the just assembled lower part of the
catcher and push the two parts together. Before you
fit the grass catcher (Fig. 5/Item 5) you must ensure
that the motor is switched off and the blade is not
rotating. Lift the ejector flap (Fig. 5/Item 7) with one
hand. With the other hand, hold the grass catcher
(Fig. 5/Item 5) by the handle and hook it in from
above (Fig. 5).
6.1.3 Setting the cutting height ( Fig. 6)
Important. Adjust the cutting height only when the
motor is switched off and the safety plug (Fig. 8/Item
15) has been pulled. The cutting height is adjusted as
shown in Figure 6.
To do so, pull the lever of the cutting height
adjustment (Figure 6/Item 10) out, select the required
cutting height by moving the lever to the left or right
and push back the lever to one of the six graduations
(Figure 6). Make sure that the lever engages properly.
•
Position 1
Cutting height: 20 mm
•
Position 2
Cutting height: 30 mm
•
Position 3
Cutting height: 40 mm
•
Position 4
Cutting height: 50 mm
•
Position 5
Cutting height: 60 mm
•
Position 6
Cutting height: 70 mm
AFTER SALES SUPPORT
1300 922 271
service.australia@isc-gmbh.info
6
Before you begin to mow, check to ensure that the
blade is not blunt and that none of the fasteners are
damaged. To prevent any imbalance replace blunt
and/or damaged blades (contact our customer service
centre on 1300 922 271). To carry out this check, first
switch off the motor and pull out the safety plug.
6.2 Battery (Fig. 2a/ Item 11)
The equipment is fitted with a lithium-ion
battery. The battery pack is completely closed and
maintenance free.
6.2.1 Battery charge level indicator
(Fig. 2a/Item 14)
The battery pack is equipped with a pushbutton
for checking the charge level. Simply press the
pushbutton (Figure 2a/Item 13) to read off the
battery level from the LEDs of the battery indicator
(Fig. 2a/ Item 14):
•
All 3 level monitoring LEDs are lit:
Battery charge level is high.
•
2 level monitoring LEDs are lit: Battery charge
level is decreasing. Stop work as soon as
possible.
•
1 level monitoring LED is lit: Battery is flat. Stop
work IMMEDIATELY and charge the battery.
Otherwise the battery's service life will be
greatly shortened.
6.2.2 Charging the battery
•
Open the battery cover (Figure 7/Item 9) by
pressing the locking button on (Fig. 7/ Item 8)
of the compartment and swinging up the cover
(Figure 7)
•
Pull the pushlock button (Fig. 8/ Item c) and
pull the battery pack (11) up and out of the
equipment.
•
Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
into the mains socket outlet. The LED A (Fig. 2b)
will then illuminate in green.
•
Push the battery onto the charger as shown in
Fig. 2a. The LED B will illuminate in red while
LED A is still green (Fig. 2b).
•
The battery is fully charged when LED A and B
(Fig. 2b) are illuminated in green.
•
Pull the pushlock button (Fig. 2a/ Item c) and
pull the battery pack (11) out of the charger.
If the rechargeable battery pack fails to charge, check
whether there is voltage at the socket outlet.
If you still fail to charge the battery pack, please call
our customer service centre on 1300 922 271.
Timely recharging of the battery will help it serve you
well for a long time. You must recharge the battery
pack when you notice that the power of the
equipment drops.
MODEL NUMBER: GL-CM 36 Li, 02/14
12
Advertisement
Table of Contents
