Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ENGIE EPS easyWallbox
Summary of Contents for ENGIE EPS easyWallbox
- Page 1 USER MANUAL...
- Page 2 INDEX INDEX SECTION PAGE SECTION PAGE ABOUT THE USER MANUAL FIRST START 1.1. About installation in Mode 2 5.1. Turning on easyWallbox 1.2. Assistance 5.2. Configuration through the My easyWallbox app ( if preferred 1.3. Symbols used CHARGING PROCEDURE 1.4.
-
Page 3: Qualified Personnel
Mode 2 sets out connection to the power Thank you for choosing easyWallbox. Please spend some minutes to read supply using plug and cable supplied with the device. Installation of the the documentation to install and use it safely, discovering all its advantages. -
Page 4: Danger Of Electric Shock And Fire
1.4. Warnings Danger of electric shock and fire Before using easyWallbox, read the contents of this manual carefully to Children or other persons not able to evaluate risks related to the acquire familiarity with the instructions for use and the safety indications. -
Page 5: Essential Safety Instructions
(garages, company depots all related risks. ENGIE Eps does not assume any liability for damage to with restricted access, etc.) and outdoor (private land, car parks, etc.), in persons or things that may arise from failure to respect the safety compliance with chapter 4 indications and local regulations. -
Page 6: Product Description
The design of the device is the result of in-depth study intended to provide an ergonomic, lean and intelligent work tool. 102 mm 102 mm f ront view side view Size of easyWallbox charging station with connector in place 325 mm 325 mm Product description Case Power cable... -
Page 7: Identification Label
Installation of easyWallbox in Mode 2 3.2. Identification label The identification label is on the backside of the charging station. The information on the label is shown in the Figure below. The data shown may differ from that in the Figure, depending on the version of the product. -
Page 8: Technical Features
To activate the Dynamic Power Management, please check the Installer Connector Standard (EV side) IEC 62196-2 Manual (see www.easywallbox.eu) on installation of the sensor on the Power supply plug E/F (G in UK, J in Switzerland) power supply and setting up the parameters. -
Page 9: Installation
- Do not use adaptors and cord extension sets. In Italy, easyWallbox must not be installed in public areas, - ENGIE Eps does not assume any liability for damage caused by as in IEC 61851-1. non-compliant use or unauthorised modifications to the device. - Page 10 Danger of fire and explosion easyWallbox must be installed in areas where there are no Do not stack loads on the box containing easyWallbox and pay incendiary or explosive substances, such as close to petrol attention to the signs and specific instructions on the package.
-
Page 11: Opening The Package
When the box is opened, check that the various parts of easyWallbox ENGIE Eps declines any liability for damage to persons or things that do not show signs of physical damage caused by knocks, lacerations may arise from the use of such tools. We recommend contacting or abrasions. - Page 12 CASE, using the groove on the bottom. The only part that can be removed f rom easyWallbox is the aesthetic cover. easyWallbox should not be opened further Using the drilling template (A3 sheet), mark where to drill on the unless by qualified personnel during installation in Mode 3, wall, using a measure tape and a spirit level.
- Page 13 4.6. Electrical connection in Mode 2 Once easyWallbox has been mounted on the wall, connect it to the power supply by putting the plug into an electrical socket. Place easyWallbox in correspondence with the holes and fix it to the wall using the screws supplied.
-
Page 14: First Start
call qualified personnel promptly so that the device can be repaired Simultaneous use of My easyWallbox and smart charging function or, if irreparably damaged, taken out of service from the vehicle may lead to minor functional issues. -
Page 15: Charging Procedure
There is a strip of LEDs on the front of the charging station which Once installation is completed, recharging an electric vehicle with easyWallbox is very easy. All you have to do is: combines visual signals and alarms indicating the status of... -
Page 16: Stop Charging
If the charging process is not completed, it must first be stopped. The interruption can be done in two different ways: Directly through electric vehicle dedicated control (see the vehicle instruction manual for more details). easyWallbox Using My app. Once the process is stopped, refer to the next chapter. -
Page 17: Maintenance
If the device is damaged, follow the instructions below precisely to avoid dangerous situations, with the resulting damage to persons or things: The only part that can be removed f rom easyWallbox is the avoid using the damaged device ... -
Page 18: Dismantling And Storage
Risk of electric shock. Before starting dismantling, be sure that the easyWallbox is not connected to any power supply. Any operation of installation, maintenance and dismantling should only be done when the power supply is switched off on your service panel. - Page 19 - the temperature of the place where the device is stored must be If you have any questions about the installation of easyWallbox, contact between -25°C and +40°C the authorised assistance centre. Various assistance centres available to - the average temperature over 24 hrs must not exceed 35°C...
- Page 20 The Italian version of this manual is the original. Instructions in other languages are translations of the original manual. ENGIE Eps will not be held responsible for any damage that may directly or indirectly result to people, things or animals due to the failure to comply with all the prescriptions indicated in this Manual and the warnings regarding the installation, use and maintenance of the easyWallbox.
Need help?
Do you have a question about the easyWallbox and is the answer not in the manual?
Questions and answers